Search Documents

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By A. S. Ibrado, D. W. Fuerstenau

The adsorption of the cyano complexes of Ag(I). Cu(l), Hg(II), Cd(II), and Zn(II) on activated carbon was investigated as a function of pH and correlated with the speciation diagram for each metal. The results show marked changes in uptake with pH, closely resembling the predominance profiles of their neutral and singly charged cyano complexes. Multicharged negative complexes are repelledby the negatively charged carbon surface. The sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the coadsorbing counterions. For the same reason, activated carbon is selective to metals that preferentially form neutral and singly charged cyano complexes, namely gold and silver.

Jan 1, 1990

By Robert Sturk, Knut O. Halvorsen

"INTRODUCTION AND BACKGROUND The world needs visionary people to break new ground and bring development forward. The human race has an inherent power and lust to explore and push borders, but also to connect and bring people together. Transport of people and goods has through history been a key factor to develop societies and increase collaboration between people and regions. Today, in the era of globalization, efficient transport systems are still vital for further development. Often, ideas of bold projects, like long bridges or tunnels, have been raised long before those projects are realized and actually built. This shows that visions must gradually be transformed into feasible business cases and sustainable political solutions. In some cases also technological development is necessary to make visions come true. Isambard Kingdom Brunel, indeed a visionary engineer, completed the oldest underwater tunnel in the world when the Thames Tunnel in London was opened in 1843. This tunnel is still in operation and now part of London’s rail transport system. Another milestone for the tunnelling industry was passed when the 54 km long Seikan tunnel in Japan was opened in 1988 after more than 15 years of construction. This tunnel is presently the world’s longest railway tunnel. Together with the 50.5 km long Channel tunnel between the UK and France, which has the longest undersea portion 37.9 km, they constitute examples of pioneering engineering projects that bring the industry forward. In 2016, the Gotthard Base Tunnel will be opened and then becomes the longest railway tunnel in the world with its 57.1 km. The trend is obvious that tunnels throughout the world are getting longer and longer. The Brenner Basis Tunnel presently under construction will yet again break the record being 64 km long. Presently, a number of even longer tunnels are planned and under design, some of these also have very long subsea portions, e.g. Bohai Straight Tunnel (123 km), Irish Sea Tunnel (around 100 km) and the Helsinki – Tallin fixed link (approximately 90 km). Northern Europe sees an increasing demand on efficient transport corridors to meet the growth of freight transportation between the Scandinavian Peninsula and central-Eastern Europe. Sustainable solutions will be required, and a shift from road/maritime transports to rail is imperative. Consequently, this paper describes yet another visionary project, a fixed railway link between Sweden and Germany, the Shortcut, to enhance traffic between these regions and to make it greener. It is true that this project still requires some work from politicians, economists and engineers to be realized, however, building a 100 km long tunnel under the Baltic Sea may become reality sooner than we think."

Jan 1, 2016

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

The estimation of local recoveries, such as the local recovered tonnage of ore and its corresponding grade at a given cutoff grade, is an important problem in a selective mining operation. Multigaussian kriging provides a simple solution to this specific problem. The solution is also complete in the sense that local recoveries are estimated together with their estimation variances. It is thus possible to assess confidence limit intervals on the estimated recoveries. Multigaussian kriging has been applied to the Jerritt Canyon deposit in a most realistic situation. The various steps of the estimation procedure are presented in detail and the potential of the method is demonstrated in view of the results. The obtained results show that the estimated recoveries are in good agreement with the actual recoveries and the actual estimation errors are correctly predicted by the estimation variances. Multigaussian kriging thus appears as a useful and fully operationable tool for the mining industry.

Jan 1, 1986

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2,3,4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6,7) and Majima and Takeda (El. These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

By S. K. Das Gupta

The rock laterite was first discovered and described in the State of Kerala, India in 1800 A.D. by Francis Buchanan. It had been used here, and elsewhere in India, for many centuries as a building stone, but in Buchanan's time it was not known that some of these laterites were highly aluminous and could be processed to produce alumina. After World War I India started searching for bauxite reserves with a minimum grade of at least 50% A12O3. By 1960, it was estimated that India had a potential reserve of 245 million tonnes of bauxite, about 10% of which was in the "Proved" category. Subsequent geological exploration now reveals that India has an overall resource of more than 2 billion tonnes of aluminium ore, not all of it bauxite, as defined by earlier geologists. In this paper, the geology, resources and distribution of bauxite and aluminium ore throughout India are described. The generalised stratigraphy, typical laterite and bauxite profiles and summary of the resource position are shown in the attached Tables 1 to 8. It is generally agreed that a tropical to sub-tropical climate, intermittent wet and dry season, good permeability of country rock and suitable drainage, as well as physiographic and ground water conditions are important in the development of bauxite.

Jan 1, 1984

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC's, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD's dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By M. W. Osterberg

The Cyprus Pinos Altos mine exploits small high grade Cu-Zn skarns using trackless equipment and a modified room and pillar mining method. The skarns occur around early Laramide diorite and quartz monzonite stocks. Stage I calc-silicates and sphalerite developed in the Pennsylvanian Magdalena Group between diorite and the marble front and were partially incorporated into a diffuse breccia body. Stage II calc-silicates and Cu sulfides formed in the contact zone with quartz monzonite and along NE-SW faults, overprinting stage I rocks and breccia. The result is a geologically complex deposit formed in two distinct pulses.

Jan 1, 1992

By M. Girardeau, J. Blondin, M. Nomine

It is well known that surface moisture and fine content have a strong influence on coal handle- ability. It is known as well that these two criteria are not sufficient to classify coals. It seems that certain types of coals are intrinsically difficult to handle, the reason being still not well understood. For these coals, moisture and fine content are aggravating factors and have to be strictly controlled in order to avoid handling problems (sticking, arching in hoppers.. .). CERCHAR has undertaken research aimed at identifying the role of intrinsic characteristics of coal with regard to handling properties. Two of them have been identified as particularly relevant : the clay content and the "colloidal particle" content. Two simple tests commonly used for soils characterisation, but never used so far for coal, have been applied to characterise a wide range of coals. The derived classification has been compared with an empirical classification based on dry screening tests. DRY SCREENING EXPERIMENTS Dry screening at a relatively low screen aperture (e.g. 6 mm) may be considered as a good tool for assessing the handleability of wet fine coals. Difficult to handle coals always lead to rapid plugging of the screen whilst easy to handle coals can be screened without difficulties. A wide range of coals has been selected with various ash, moisture and fine content. Their characteristics are given in table 1. The experimental set-up consists of a 2 t.p.h vibrating screen equipped with two automatic re- cording balances collecting respectively oversize and undersize material. Provided that the feeding rate is accurately controlled, good reproducibility in the percentage passing as a function of time is obtained. Figure 1 gives examples of different types of relations that were obtained. - LMC coal exhibits a behaviour that is characteristic of easy to handle coals : % passing remains constant in the course of the screening operation. - B coal behaves slightly differently. One observe first a rapid decrease in the flow passing through the screen and then a stabilization. Hand- ling properties can be considered as intermediately - The curve relative to LHB coal is characteristic of a very difficult to handle coal that blinds the screen almost immediately. It is necessary to point out the fact that the classification derived from screening experiments is a global one, including not only intrinsic factors but also external factors such as fines and moisture content. The role of surface moisture is in particular very important and variations in this parameter may upset the empirical classification

Jan 1, 1988

By Neil Hillhouse

The Porgera gold district, like many other large gold deposits, has a long history of awareness, but only in the last five years has a geologic understanding of the district permitted the discovery of economically attractive gold reserves. The following sequence of events highlights the various significant steps in the evolution of the discovery process. The history of the district goes back about 50 years, and for several decades it was known only for its placer gold. Gradually, as gold became a more interesting metal, more and more attention was centered on the district. The sequence of events does not overstate the problems caused by isolation and climate, but the reader can imagine the difficulties inherent in such an area.

Jan 1, 1990

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By James R. Arnold, John G. Mansanti

BACKGROUND Gold Fields Mining Corporation started their Chimney Creek operation in late 1987. The dump leaching operations commenced in October and the mill startup took place during the last half of November. The milling process at Chimney Creek is almost a conventional CIP plant with the major exception being the installation of a second thickener as a washing stage prior to CIP12 ' A simplified flow sheet is shown in FIGURE 1. Most of the gold in the mill is liberated by grinding in cyanide. After grinding in a conventional SAGball sill circuit, the cyclone overflow reports to the thickeners. The thickener overflow from the first thickener is pumped through 5 stages of carbon columns for gold adsorption. Slurry from the thickener underflow is leached, washed, re-thickened and pumped to CIP. After approximately 6 hours of retention time in CIP, the slurry is pumped to tailings for final deposition. The carbon from CIP is transferred to the third stage of carbon adsorption and then advanced as normal through the columns and strip circuit. Loaded carbon is stripped at approximately 1500C (3000 F) and 55 kPa (80 psi). After 4-5 hours of stripping, the grade of four tons of carbon is reduced from 5,140-6,860 g/t (150¬200 oz/ton) to typically 17 g/t (0.5 oz/ton). Zinc precipitation is used to recover the gold from the pregnant solution. After a water wash, the stripped carbon is transferred to acid wash or to the kiln feed tank for reactivation. All strip lots are acid washed in 3.0% HC1 and all stripped carbon passes through the kiln for thermal reactivation. Then the carbon is quenched, sized and stored in tanks or bins for transferral to CIP or to the carbon columns. Loaded carbon from the dump leach circuit is treated in a circuit consisting of five carbon columns which are parallel to the mill circuit. No distinction is made between the mill or dump leach carbon once the gold has been stripped from them. CARBON FINES HANDLING Once the carbon has been transferred from the carbon columns, every effort is made to minimize carbon attrition and to recover the carbon fines that have been generated in the process. Wemco Hidrostall pumps are used for transferring all carbon in

Jan 1, 1990