Search Documents

By A. E. Aldrich

The Pittsburg & Midway Coal Mining Co. (P&M) is expanding a combination of surface and underground coal mining operation in Northeastern New Mexico. The York Canyon Complex, located 35 miles west of Raton, New Mexico, is aggressively pre-paring for increased production while meeting present requirements. Surface mining activities in four separate mining areas are preparing the complex for additional markets. Drag-line, truck/shovel, highwall miner and contour stripping are surface mining methods currently planned. In addition, P&M will move a Marion 8200 dragline from Kansas to the York Canyon site, finish constructing a $20 million coal preparation plant, and complete conveyor upgrades to the existing underground mine. This paper will describe the diverse York Canyon Complex.

Jan 1, 1993

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

This chapter contains the edited transcript of the "Gold Heap Leach Information Exchange" session that was held at the 1990 SME/AIME Annual Meeting in Salt Lake City, Utah. The exchange occurred on the afternoon of February 27, 1990. The session was intended to act as a forum for discussing some of the more prominent operating problems associated with heap leaching precious metals. The information exchange was very successful. The exchange consisted of several panelists introducing and discussing different topics, follow by a comment and question period. This transcript contains the panelists' presentations as well as comments and questions from the floor and the panel. Extraneous comments and remarks have been edited out. Some wording has been changed for clarity, but the transcript is basically an accurate account of what was said. At the end of the transcript are two papers submitted as part of the panel discussion

Jan 1, 1990

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By William A. Vogely, John E. Tilton

INTRODUCTION Mineral commodities are normally separated into three generic classes-metals, nonmetals, and energy minerals including oil and gas as well as the solid fuels. Metals, the focus of this chapter, encompass a large number of different substances. The U.S. Bureau of Mines, for in- stance, has commodity specialists following trends in over 40 metal products of importance to the country's economy and well being. Ranging from aluminum to zirconium, the metals display an incredible degree of diversity. Some such as lead are heavy, others such as magnesium are light. Some such as copper are good conductors of electricity. Others such as silicon are semiconductors. Mercury is found in liquid form, while some metals melt only when heated to extremely high temperatures. Iron and steel, aluminum, and copper are consumed in particularly large tonnages in a multitude of end uses, while many minor metals are needed in only small amounts in a few highly specialized applications. The use of some metals can be traced back into history for millennia, indeed back to the bronze and iron ages, while the commercial consumption of aluminum and other newer metals is less than a hundred years old. Some metals are extracted from large open pits, others are dug out of deep underground mines, and still others are processed from the sea. Mining and processing can be relatively uncomplicated and inexpensive, though in most instances highly sophisticated technology is necessary and the costs are high. Some metals are produced mainly as byproducts of other metals. Some are recovered in large quantities from the scrap of obsolete equipment and demolished buildings. Some are mined in only a few locations and traded worldwide, others are produced in many different countries. Some are sold by numerous firms at fluctuating prices determined on competitive commodity exchanges, others are produced by only a handful of firms and sold at stable producer-prices. This diversity makes the metals interesting, indeed fascinating, to study. Yet, it also poses problems, for each metal in its own way is unique. There is no general model or economic analysis applicable to all metals. Rather each must be considered individually, so that the analysis or model takes explicit account of its particular features. This means that a single chapter cannot begin to cover comprehensively the economics of all metals, and no attempt to do so is made here. Instead, we will concentrate on illustrating the usefulness of relatively simple economic principles, particularly those associated with supply and demand analysis, in understanding the behavior of metal markets. The next section begins by exploring the nature of metal demand. It is followed by an investigation of metal supply- from individual product production, from by- product and coproduct production, and from secondary production. The final section then illustrates the usefulness of the concepts introduced in earlier sections by using them to analyze

Jan 1, 1985

Jan 1, 1999

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin

In the aftermath of the September 11th attack on the World Trade Center, groundwater control was of immediate concern. Water in?ow from the adjacent Hudson River through the compromised slurry wall ‘bathtub’ surrounding the site, ruptured water and sewer mains, and saturation from fire hoses all contributed to an already critical situation, further hampering the recovery and rehabilitation effort. An extensive pumping and deep well installation program was initiated, focused on reducing the hydrostatic loading to the severely damaged perimeter slurry wall.

Jan 1, 2003

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By A. Kepeski

Cement industry relies heavily on the control of large volume of raw materials in the proximity of plant operations for clinker and cement manufacturing. These mineral resources are perhaps considered as ?low-profile? (mostly comprise limestone's, clays, marls and sands), but their availability, accessibility and suitability ? the later with respect to chemistry, mineralogical and physical characters ? are factors of paramount importance and may largely affect production cost and plant productivity. The combination of scarcity of good quality raw materials deposits and the growing environmental concerns have challenged the cement producers towards sustainability and the responsible exploitation of natural resources. In open pit mining and quarrying, the evaluation of mineral resources vs. handling of the non-usable overburden and other off-spec materials directly affects the medium to long-term production planning, quality control practices and environmental management. It is a general trend for many cement producers and a usual case for a number of Titan Cement plants worldwide, that redesign of quarry pits is necessary not only for stability purposes but also as a result of environmental constraints and emerging issues. The material reserves then have to be re-evaluated in the light of the new final pit design, safety distances from houses, other infrastructure and Law restrictions and according to criteria of safety of operations, reduction of environmental impacts, pit optimisation and proper future reclamation. The paper discusses the case of three active quarries of Usje Cement Plant, in Skopje (Macedonia), namely Usje (marl), Goverlevo (lime-stone) and Ljubosh (sand), where a large campaign of redesign and evaluation of recoverable reserves and the needs in rehabilitation took place in 2004. Technical and environmental issues and criteria are presented in the form of master plans and the highlights of the first attempts to propose and apply a reclamation scheme are discussed, by also examining alternative solutions for each quarry area. Finally, the 2005 progress in applying changes to the design of benches and pit layout, as well as experiences gained, are discussed.

Jan 1, 2005

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993

By S. P. Winkelmann

The expansion in gold production in the Carlin 'Trend over the last few years has been one of staggering proportion. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the Mine Engineering group at Newmont Gold. This paper discusses the organizational changes implemented to effectively deal with a full range of engineering problems and how the Newmont Gold Mine Engineering group dealt with these problems. Specially developed computer software and their applications will be explained. Improvements in the techniques used in converting geologic resources into reserves, and in scheduling the mining of multiple pits to feed multiple processing facilities, as well as ore control procedures are presented. Current mine engineering practices are discussed.

Jan 1, 1990

By Jesus M. Rohena

Concrete pipes and small boxes have been installed by the jacking method. This paper will describe a recent project were large concrete boxes were installed by the jacking method. This project is in the city of Boston, MA. By now everyone in the USA knows something about this project. The project official name is The Central Artery/Tunnel Project (CA/T). This is the biggest public work project in the USA right now, with an estimated construction cost of 14 billions. The main objective of the CA/T project is to replace an existing artery built in the 1950s to increase capacity and safety. One section of the new artery will cross under several railroad tracks near the South Station. To construct the section of the new artery under these tracks, big concrete boxes were installed by the jacking method. The jacking method can be used to install pipes, small concrete boxes, and the CA/T project has demonstrated that big concrete road tunnel boxes can be installed by jacking.

Jan 1, 2003

By J. I. Schoenherr, G. Schubert, T. A. Baloun

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts and different numbers of plastics types as well as of fine bulky materials (<4mm). These wastes are mostly given to land-fill sites. Thermal adhesion seems to be a great means to efficiently separate plastics mixes. Tests carried out at a special lab-scale testing unit (TaA1) confirm the effectiveness and feasibility of the separating mechanism. The thermal properties of the individual types of plastics differ from each other to a sufficient degree so that special products or product mixes of high material purity can be obtained according to the respective requirements. For this reason, plastics mixes such as PE and PP can be sorted with very good results. The separation efficiency is influenced only by different contact surfaces. The contact period can be adjusted to a short period of time so that sorting large amounts of fine dispersed plastics seems feasible. Sorting processes in feed streams were shown to be technologically effective when applying appropriate technologies. For the time being, the technological application of a thermal adhesion drum separator (TaTr1) is suitable. First tests on such a pilot-scale unit provided good separation results.

Jan 1, 2004

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

By K. V. Raj, T. Bhowmick

"Computational fluid dynamics (CFD) modeling of an open-pit mine has several challenges. A good quality mesh of the model domain is a pre-requisite for convergence in solution. Good quality tetrahedral meshing and insertion of prism layers in faceted open-pit mine geometry is complicated due to presence of numerous vertices and ridges. Presence of vertices and ridges result in poor quality tetra elements and holes in prism layers, which cause instability in the model. Good quality pit bottom prism mesh elements significantly improve the formation of velocity boundary layer and thermal boundary layer at the pit bottom. This results in an expected temperature dependent micrometeorological buoyancy flow in the pit. Whereas, model geometry without a prism layer, results in abrupt temperature gradient near pit bottom. Buoyancy flow and recirculation have significant effect in lifting mechanism of fugitive dust particles generated near pit bottom. Representative initial and boundary conditions and selection of appropriate turbulence model have significant influences on the simulation results. In this paper, three-dimensional models of open-pit mines are developed using commercial CFD software (CRADLE-CFD). Important constraints and various consequences in modeling complex open-pit geometries are presented. INTRODUCTION Application of Computational fluid dynamics (CFD) to model an open-pit mine to predict fugitive dust and pollutant concentrations in and around a mine is relatively new. In former Soviet republic (USSR), Baklanov [1] and Belousov [2, 3] presented numerical models of pollutant transport in open-pit mines in Arctic regions. In recent years, advances in mathematical and computational fields have enabled better modeling of pollutant dispersion phenomenon around mines using computational fluid dynamics (CFD). Several CFD software packages have been used by various researchers to model the pollutant transport in open-pit mines. Works by Alvarez et al. [4]; Lowndes et al. [5]; Silvester et al. [6]; Torno et al. [7]; Choudhury and Bandopadhyay [8]; Collingwood et al. [9]; Raj et al. [10] and Flores et al. [11]; are examples of application of various commercial and open source CFD packages (COMSOL, ANSYS, OpenFOAM) to model pollutant transport in open-pit mines. These researches provided a strong background for additional research involving CFD modeling of open-pit mines. Due to the limitations of computational times and capacity, 3D modeling and various aspects of fugitive dust dispersion in open-pit mines remained unexplored."

Jan 1, 2015

By J. Ke

Traditional geostatistical methods have been used in ore reserve estimation for decades. Neural Networks (NNs) have provided an alternative approach to data analysis and ore reserve estimation. Unlike the traditional geostatistical methods, neural network uses a highly non-linear complex algorithm to do the estimation. Although Neural Networks have been demonstrated to be attractive alternatives as with every new techniques, there are questions which remain unanswered. This paper presents a comparative analysis with different types of metamodeling approaches -- Triangular, Kriging, Spline, and Neural Network. The neural-network is organized in a multiple-layers and Back-propagation model is used to handle the non-linearity and hidden slabs for smoothing the predicted results. With multiple dimensional and very noisy drill hole sample data, the ore grade is predicted and the overall performance is validated by the analysis of R-squared (R2), Root-Mean-Squared (RMS), and contours of ore grade spatial variability. The ore grade and tonnage of estimated outputs are also compared with various cut-off grades.

Jan 1, 2003