Search Documents

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By Harry M. Conger

Thirty years ago, the U.S. gold mining industry was hanging on by its fingernails. Save for one great mine, the Homestake, most production was coming from copper smelters such as Kennecott and Magma. Even Homestake itself was under great pressure from rising costs and a fixed price for gold. The outlook was dim, to say the least. Today, as it has for most of the past decade, the American gold mining industry stands among the world leaders in production, and in the development of mining and mineral processing technology. What caused this dramatic change? Obviously, the freeing of the gold price was a major factor, as was the decline in South African production, but these events alone could not have created the U.S. strength we see today. It was technology, investment, and the determination of miners to build an entirely new industry that were the indispensable ingredients. The U.S. Bureau of Mines, with great foresight, had begun the research that led to heap leaching before the gold price began to rise, and Newmont had committed to build a small mill at Carlin, a move then considered quite risky. From that point, the U.S. gold mining industry was placed on lower-grade ores then being found in Nevada and elsewhere, but it was soon apparent that we would have to develop new technologies to deal with more refractory ores, carbonaceous as well as sulfide-bearing. This is now being done with considerable success. Despite its success, or perhaps because of it, the gold mining industry has come under pressure from various groups who characterize their activities as motivated by "public interest." The public interest they refer to properly include the health and safety workers and impacted communities, as well as protection of the environment, and with these concerns we miners have relatively little argument. In fact, we consider health, safety and the environment among our highest priorities, and not just because regulations may require us to do so. The argument, however, is not about the regulation of a viable mining industry, it is about a well-organized movement to attack and condemn mining in the media and to misrepresent its importance to the Nation and its willingness to accept responsible regulation. Once largely local or regional, the interest groups to which I refer are now quite large, national in scope, and even becoming international. This trend, taken together with finances raised from their dues and contributions, would make the interest groups formidable adversaries for mining, but their grip on the media enormously magnifies their influence. Unfortunately, it also makes possible the wide dissemination of incomplete, incorrect or slanted information. I am not here to "bash" the interest groups. On the whole, I believe that many of them have made positive contributions to society. As conservationists, however, I question their authority to make, or foster, decisions about which American industries and communities live and which die. To illustrate, I would like to present for your consideration the problem of cyanide, one of the issues over which the gold mining industry is most threatened. CYANIDE-POISON OR MIRACLE SOLVENT? Let me get this out of the way right up front: cyanide in most of its chemical forms is toxic. In some forms it is also listed as a carcinogen. These are adverse characteristics cyanide shares with a considerable number of industrial chemicals, including some that are widely used without the stringent regulations already in place for the mining uses of cyanide. In these uses, by the way, the risk to humans comes from direct ingestion of cyanide or cyanide-bearing solutions, or from the accidental acidification of solutions leading to release of hydrocyanic acid gas. That these risks are under control in mining can be seen from the fact that, in modern U.S. practice, there has never been a documented fatality attributed to cyanide! Because of its toxicity, cyanide cannot enter and be accumulated in the food chain. It can, however, be a threat to birds and animals that ingest cyanide-bearing solutions. Protection against this is, quite properly, a responsibility of individual mining operations, and considerable sums are spent each year to prevent or reduce bird and animal exposures. It should be evident, though, that many human activities, including highway traffic, windmills, use of pesticides and the like, result in bird and animal losses. Mining's use of cyanide, and the measures taken to protect birds and animals, should be considered in context. Cyanide must be kept out of surface streams and groundwater, and existing regulations mandate this. Any cyanide residues left in leach heaps, waste dumps and disused facilities must be eliminated, and we have proven technologies to do this now, just as we have means to detoxify tailings prior to disposal. The gold mining industry decries those rare instances when irresponsible operators fail to deal with contamination, and agrees that they should be held responsible. We do not agree, however, that the great majority of responsible companies should be punished, in advance, for accidents that have never happened. So much for the poison, what about the "miracle solvent?" Is that an overstatement? Well, consider the fact that gold has been called "noble" from earliest times, because it does not oxidize under atmospheric exposure, and that it appeared to the ancients to be utterly insoluble. Later generations of scientists did discover that it could be dissolved, but only by a combination of acids so potent that it became known as aqua Regia. Later still, it was found that chlorine would also dissolve gold, and attempts were made to base commercial processes on this, without a great deal of success. It remained

Jan 1, 1995

By G. M. Clarke

Minerals are certainly where they are found. The undemocratic distribution of the world's mineral wealth has created an incongruous inbalance: mineral-rich, scarcely populated countries supply highly-populated industrialised countries that in turn consume more minerals than they produce. This has been as much a generating force for colonisation, invasion, and war as religion, political ideals, or megalomania. The Industrial Revolution of the seventeenth century was born in Britain, a country with large domestic resources of coal, iron, lead, zinc, copper, tin, etc., as well as a large population. As consumption outstripped production imports filled the gap, particularly from its worldwide colonies. For example, when Canada was founded in 1867 more than 905 of its investments were British financed, and much of these were mineral-based. The British made similar investments in South East Asia, Australasia, the Caribbean, and elsewhere, as did the other industrialised Western European countries hungry for raw materials. Later the United States emerged as a leading industrial power, again due largely to its abundant natural resources. Consumption soon exceeded production and foreign sources were saught. American business went exploring abroad ant many a mineral resource was developed almost totally on the basis of the US market many .thousands of miles away. Closer to home, Canada was also an obvious target for the US with its rich mineral resource base, small population, and geographical juxtaposition, so much so that about the time of the 1914-18 War the US took over from Britain as the major investor in Canada, and this peaked in 1967 when the US accounted for 80% of the country's foreign investment. After the 1939-45 War Japan joined the ranks of the USA and Western Europe as industrialised powers, and they too searched the world for the deposits lacking in their homeland.

Jan 1, 1981

By Richard J. Fantel

This paper addresses the impact of declining world rutile resources upon the production of titanium products and their asso¬ciated costs. Titanium is used primarily for the production of pigments; in its metal form it is considered a strategic and critical material to the U.S. defense and aerospace industries. There are two major mineral sources for titanium: ilmenite and rutile. Both these mineral types can be used to produce titanium pigments. Only high grade titanium concentrates, such as rutile, high-grade ilmenite, and synthetic rutile (which is produced through further processing of ilmenite), can be used in the production of titanium metal. This paper draws upon the data and analyses of a recent Bureau of Mines Minerals Availability Program appraisal that evaluated the international availability of titanium from market economy countries. The paper will show that production from economic rutile mines will decline sometime after the turn of the century and that rutile shortages could be alleviated by production from other high-grade titanium resources such as higher cost rutile deposits and anatase deposits, or through an increase in world synthetic rutile capacity.

Jan 1, 1984

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By Jianmin Qin, Raja V. Ramani, Wilson Miola

The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine. In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.

Jan 1, 1991

By L. Schlink

Impacted waters, often complex, are created in mining which at some point in the mine life cycle will need to be attended. The simplest and most cost effective method of handling impacted water is to reuse it as makeup water for operations. At the end of mine life, operational reuse will not be an option and the impacted water will require treatment to achieve alternative reuse goals. Conventional mine impacted water treatment is successful in removing unwanted constituents but create brine and sludge that may require special handling or additional treatment, resulting in additional liabilities and costs. Freeport-McMoRan Copper & Gold has taken an approach to water treatment that focuses on transformation not concentration. The Water Treatment Test Facility located at Sierrita Mine has three test plants that are piloting the mine impacted water transformation process. Two plants have been designed for the removal of calcium and sulfate with products of gypsum and sulfur. The third plant removes metals from process water and transforms them into marketable metal sulfides. The transformation, rather than concentration, of mine impacted water solutes greatly reduce long term risks.

Feb 23, 2014

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By Kalyan Saikia

An integrated statistical-geostatistical modelling of gold exploration data of Gurahar Pahar prospect of Mahakoshal greenstone belt in Central India has been attempted. Statistical modelling of gold accumulation and width reveal a positively skewed 2-parameter lognormal distribution fit with an estimate of mean gold as 0.84 gram/tonne. Geostatistical modelling provided a spherical semi-variogram function fit with mean kriged estimate and mean kriging variance of gold as 0.76 gram/tonne and 0.23 (gram/tonne)2 -respectively. Ore inventory and grade-tonnage relationships for a selected part provided an estimate of 3,36,000 tomes of ore with an average gold of 0.76 gram/tonne at 0.5 gram/tonne cutoff grade.

Jan 1, 2002

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By William I. Weisman

The annual consumption of fluorspar in the United States, in the last 10 years has doubled. In 1971, when 1,344,742 tons were consumed, almost 45 percent of this amount was used in the production of steel and nearly 50 percent was consumed in the manufacture of hydrofluoric acid. Of the hydrofluoric acid produced, about one-third was used in the manufacture of aluminum electrolytes for production of primary aluminum metal and the balance was consumed in the manufacture of a variety of fluorocarbons and other chemicals. A small amount of fluorspar, constituting less than five percent of total consumption, was used in the foundry industry, and in the manufacture of glass, enamel, cement and other products. It is apparent that a continuing supply of fluorspar will be required to meet the demands for these vital metals and chemicals in our expanding industrial society. Domestic fluorspar production meets only approximately 20 percent of our needs. Hence, it is essential that the United States maintain a healthy domestic fluorspar industry in order to have adequate domestic reserves available at times of emergency and to protect this country from becoming solely dependent on foreign sources for this strategic commodity.

Jan 1, 1973

By Yeonuk Choi, Patrick R. Taylor, Lyle Cunningham

Laboratory experiments have been performed to evaluate the potential for metal removal and recovery from river bed tailings by ferric chloride leaching. The lead, zinc, silver and other metals in the river bed occur due to the old method of dumping mill tailings into rivers. This was practiced prior to the introduction of tailings impoundments. The effects of the leaching method, leaching time, pulp density, ferric chloride concentration, and leaching temperature on the rates and recoveries of lead, zinc and silver were studied. The effects of pulp density and leaching temperature were significant on the extraction rates of lead, zinc and silver. The lead content in the leached tailing was reduced to 0.023 percent, when using an 353O K leaching temperature and 0.384 g of FeC13/1 g of sample.

Jan 1, 1992

By E. Wm. Heinrich

Glass sands fall into that extremely select category of mineral deposits that requires a fantastic degree of natural concentration (95% +) of a single component before they can even be considered as ores suitable for further refinement. The combination of geological factors that has produced such an environment of "mineralogical single-mindedness" has appeared only rarely. Factors that require consideration in the economic evaluation of a potential glass-sand deposit can be grouped into three categories: 1) geological (e.g., size, shape, structure); 2) petrographic (e.g., grain size, accessory minerals, nature of iron contaminants); 3) geographic - political (e.g., proximity to consumer, size of market, zoning restrictions). Of particular con ern is the nature of the iron contamination. Iron-bearing species appear as 1) accessory mineral grains, either detrital or authigenic, 2) cements, 3) grain coatings, and 4) quartz-grain inclusions. Selection of the cheapest form of beneficiation requires precise information on the mineralogy of the iron species and their detailed petrography. Because of the antipathetic relationships, in many parts of the United States and Canada between the geographical locations of glass plants and the geological distribution of glass sands, the selection of ac suitable source for a particular glass plant may be dichotomous. One may seek either an exceedingly pure "classic" type glass sand that is relatively distant and whose cost includes a major transportation charge or a relatively proximate and somewhat "impure" source whose cost includes a substantial fee for beneficiation.

Jan 1, 1974

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By Philip L. LeHoux

In recent years, much work has been done to explain the nature of the gold-carbon adsorption mechanism. The benefits of a sound theoretical basis has the obvious application to gold adsorption and elution industrial processes. Unfortunately, the lack of a clear agreement on the mechanism has provided no clear direction towards process innovation and optimization. Jones' (1989) work has gone a long way towards clarifying the specie of gold adsorbed (and thus the chemistry required to remove it). Since the development of hot caustic and cyanide elution, the kinetics have been accelerated by the application of pressure to increase elution temperatures beyond the boiling point at atmospheric pressure. However, the traditional reagent content of 15 g/L NaOH and 5-10g/L NaCN has remained largely unchanged. This is in spite of work that has shown that the presence of cyanide is not required for the elution process to take place (Adams, 1986; Adams; 1989; Jones, 1989). Adams (1989) has also compared NaOH elution rates with and without cyanide. He found improvement with the use of cyanide and a synergistic effect with the use of both. Others have found no difference in overall extraction (Jones, 1989

Jan 1, 1990