Search Documents

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu co-deposited. Decreasing Cu co-deposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave e1ectrowinning at 70? C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 ms to 1,000 ms gave the following results: Ag concentrations decreased from 34 µ g/mL to 0.1 µ g/mL, Au concentrations decreased from 54 µ g/mL to 0.2 µ g/mL, and Cu concentrations remained almost constant at 560 µ g/mL.

Jan 1, 1993

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By George C. Hawley

Historically, mica usage has been low because of limited availability; as a by-product of many small processors, who have lacked motivation for extensive R & D. The discovery of a 30 million ton deposit of 85-90% pure phlogopite, when existing markets are only 300,000 tonnes annually, forced the search for large volume new markets. Increasing costs of energy, petrochemicals, plastics and glass fibers, and environmental constraints on asbestos usage, have led to new opportunities for mica as a reinforcing filler. Extensive research and developments; in beneficiating, processing and treating mica, has been necessary to satisfy these new markets.

Jan 1, 1981

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

A major Brazilian iron ore producer, SA Minerayao da Trindade (Samitri), has recently completed modifications at two operations which involve the use of Derrick high frequency vibrating screens. Details of these modifications are presented, together with a review of product quality improvements.

Jan 1, 1997

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By Josh Willhite, Seth Pollak, Ben Seling

The Long Baseline Neutrino Facility Far Site at the Sanford Underground Research Facility in Lead, South Dakota will house four large detector tanks located in deep underground caverns. Construction of the supporting infrastructure required for this project is no complete including installation of a waste rock conveyance system and drill and blast excavation of several supporting drifts and chambers. This paper will discuss the design and construction of these pre-excavation and early works elements, and the overall project schedule as it closes in on commencement of cavern excavation activities.

Jun 13, 2021

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By B. S. Hulvey

Thin support liners are becoming more accepted and being developed with improved properties because the mining industry as a whole has been offering underground safe test trial sites. This is because of the huge potential for such products. Recent developments tend to indicate that the technology is “coming of age” and these are discussed in this paper.

Jan 1, 2003

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By M. J. Zdunczyk

The final 1995 figures on industrial sand and gravel have not yet been compiled by the US Geological Survey (USGS). There is usually about a nine-month lag time in receiving and compiling this information. However, USGS estimates that domestic production of industrial sand and gravel will increase about 4% to 28.2 Mt(31 million st). The average unit price is expected to increase as well. The top five producers during 1995 were Unimin, US Silica, Fairmount Minerals, Oglebay Norton and Morie Co. Glass manufacturing for containers, automobiles and buildings was mixed during 1995. Containers, the largest consumer of silica sand, remained steady, with regional increases. However, silica use in glass containers face increased competition from plastic and recycled glass (cullet). It was reported that the Pepsi Cola announced plans to replace glass containers with plastic during 1996.

Jan 1, 1996

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968