Search Documents

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By R. R. Klimpel

This paper describes a series of mechanical flotation cell results run with various chemical reagent schemes designed to economically improve the flotation performance associated with selected industrially available coals. The emphasis is on the identification of practical flotation methods of processing coals containing unusually coarse and/or fine feed sizes, of increasing the recovery of oxidized and/or difficult to float coal, and of increasing the selectivity of coal over pyrite in high sulfur coals.

Jan 1, 1991

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By Daniel C. McLean

Many of the major copper ore bodies throughout the world contain chalcocite (79.9% Cu) as the principal copper mineral, yet the grades of copper concentrates produced from these ores rarely exceeds 25 to 28% Cu and in one known instance went as low as 13%. The low grade has traditionally been attributed to the presence of "activated pyrite" and/or chalcopyrite, and the universal approach has been excessive regrinding with all of its inherent effects-high capital, energy and maintenance costs, excessive sliming, and concentrate filtration difficulties (high moisture content). E. P. Cadwell, former Chief Metallurgist for American Cyanamid Company, did extensive microscopical studies on several of these types of concentrates from South American operations during the 1950's and discovered they all had one common feature--the pyrite particles in the concentrate were all rimmed with thin films of secondary chalcocite or covellite. As far as a flotation bubble or reagent is concerned, a rim of chalcocite is the same as a solid particle of chalcocite, and as long as a rim is present, the particle is going to float. Upon examination of these rimmed particles under the microscope, it becomes quite obvious why regrinding will never solve the problem and why maximum increases in grade by this technique rarely give improvements in grade of greater than 3 to 5% Cu.

Jan 1, 1983

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

Keeping an eye on the future while honoring the past, Frank McAllister, chief executive officer of Stillwater Mining Co., and life member of the National Mining Hall of Fame and Museum, gave the keynote address to a packed house during the 23rd National Mining Hall of Fame and Museum Banquet in Leadville, CO on Sept. 11. McAllister?s company made news just days before the induction ceremony, when it was announced that Stillwater Mining would acquire Marathon PGM Corp. for $118 million (ME, Oct. page 14).

Jan 1, 2010

By A. Festa

Secondary crushing often gets good press for its increases in energy efficiency and SAG milling rates but for a project considering this option the proposed benefits soon get overshadowed by implementation concerns. Reverse engineering from the published case studies is risky unless the reader understands the drivers impacting stability and operability of the circuit. This paper discusses the features of secondary crushing for Greenfield and Brownfield SAG mill grinding circuits. It is the author?s view that secondary crushing rarely adds value to a Greenfield project and restricts future expansion. Its application is best retro fitted to Brownfield operations where the benefit gained for capital expended is excellent. Two case studies are presented to reaffirm these statements. The first case study shows that the implementation of partial and total secondary crushing increases SAG mill power efficiency and it offers substantial incremental increases in milling throughput with staged capital investments for the crushing and grinding circuits respectively. The paper provides a critical analysis of process conditions for secondary-crushed grinding circuits, with particular emphasis on Brownfield circuit retrofits. Furthermore, the second case study quantifies the economic impact of secondary crushing on circuit design for plant start up and it illustrates the limit imposed on plant expansion.

Feb 23, 2014

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994

By Robert Moore Lewis

A unit for separating minerals into two prescribed size fractions, designated as a Lewis Hydrosizer, was developed at the North Carolina State University Minerals Research Laboratory. Ore samples with different mineral compositions, including coal, were separated effectively with the laboratory continuous unit. Commercial size units are in operation in North Carolina and Mexico, and under construction in Norway. Additional units are being build or are in the planning stage at several companies.

Jan 1, 1983

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996