Search Documents

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

By D. Caiden, C. S. Covil, P. J. Chamley

The paper describes the background to alternative delivery models, drawing on international experience, and introduces Project Alliancing/Contract Partnering, common risks and risk sharing on tunnel projects. A plea for early contractor involvement in design is made before describing some whole life design implications for tunnels. The paper concludes with four short case studies; Channel Tunnel Rail Link in the UK, Hull Waste Water Tunnel in the UK; Island West Sewage Transfer Station in Hong Kong, and the New Southern Railway in Australia.

Jan 1, 2005

By D. R. Dolinar

Geogrids can be used as surface control on both the roof and rib in underground mines to prevent the fall of small pieces of rock and material from between the primary supports. The use of screen material such as geogrid can significantly reduce the number of ground fall injuries caused by these small rock falls. Because of the potential for reducing injuries through the use of screen, the National Institute for Occupational Safety and Health (NIOSH) has conducted tests on screen materials including geogrid to determine their support characteristics and identify parameters that can affect their performance with respect to maintaining broken or failed rock. A specially designed test frame installed in the NIOSH Mine Roof Simulator (MRS) has been used to evaluate the load and stiffness characteristics of the screen material. Two types of geogrids with various designs have been tested-a polyester yarn and a polypropylene grid. The load-displacement characteristics of these grids were determined and the load capacity and stiffness were calculated through 20in of displacement. The load capacity and stiffness of the geogrid in general are shown to be related to the ultimate tensile strength of the screen material.

Feb 27, 2013

By William Stewart, John Tinkler, Gary B. Hemphill

Of the 345 km long Taiwan High Speed Rail Project, connecting the cities of Taipeiand Kaohsiung, the 23 km alignment on Contract C230 required the construction of5755 m of shallow mined tunnels ranging from 137 m to 1285 m in length. All nine of these tunnels were mined using NATM methodology. On September 6, 2002, a collapse occurred in Tunnel T08 that affected approximately 50 m of tunnel. There was little warning. However, the crew was evacuated approximately 45 minutes prior to failure and thus, no injuries or loss of equipment. This paper will discuss the mining methods, jet grouting ground support, and the instrumentation selected for the rehabilitation and monitoring of the tunnel.

Jan 1, 2005

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By Kent von Maubeuge, Charles R. Landis

The global bentonite industry is a dynamic market balancing a range of end uses with an ever growing number of bentonite producers. In addition, markets in developed countries are elevating the level of detail and transparency for materials reporting in programs, such as the Registration, Evaluation, Authorization and restrictions of Chemicals (REACH) program in the European Union. Bentonite is impacted by programs of this nature. The majority of the bentonite products sold around the world are sodium bentonites. These sodium bentonites consist either of natural sodium bentonites, or naturally occurring bentonite dominated by divalent interlayer cations (Ca+2 andMg+2) subsequently exchanged with sodium cation. The latter variety is often called “sodium-activated“, or “soda-ash treated” bentonite. Once exchanged with sodium, these bentonites are often difficult to distinguish from natural sodium bentonites using common commercial testing protocols. Due to their similar colloidal and bulk chemical properties; the lack of test procedures designed specifically to identify this product feature; and the failure to completely or effectively explain their differences, sodium-activated bentonite is often considered to be identical to natural sodium bentonite in the industry. This article defines both general types of sodium bentonite and presents a technique that could serve the industry as a tool to confirm the variety of sodium bentonite in question. Specifically, geochemical properties such as carbon (C13/C12) and oxygen (O18/O16) isotopic ratios can distinguish activated, even slightly activated bentonites, from bentonites not introduced to additional sodium during manufacture.

Jan 1, 2004

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation are described. The applicability of the Washburn equation for surface energy evaluation in such systems is discussed.

Jan 1, 2002

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

By R. G. McLusky

This paper analyzes the opinion in Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D. W.Va. 1999), a case which threatens the future of surface mining in West Virginia and which will almost certainly result in new policies or rules that will affect surface mining everywhere. This paper addresses: (1) the jurisdictional bases of the action which relies on the federal surface mining laws to enforce a state mining program; (2) settlement agreements reached in the case that threaten to alter federal policies beyond West Virginia borders; (3) a programmatic environmental impact statement on mountaintop mining being undertaken by the federal government; and (4) an opinion by the Court outlawing excess spoil disposal in intermittent and perennial streams.

Jan 1, 2001