Search Documents

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By A. Yazadni-Chamzini

Maintenance strategy selection plays a significant role in mining design. The nature of maintenance strategy selection is a complex multi-criteria decision making (MCDM) problem including both tangible and intangible parameters which are often in conflicting with each other. Moreover, when decision makers are uncertain in determining and defining the ratings and the weights of alternatives and criteria respectively, fuzzy theory provides an appropriate tool to handle the existing uncertainties. In this paper, a new fuzzy MCDM method based on the concepts of TOPSIS and AHP was proposed to evaluate the feasible maintenance strategy. The linguistic terms are employed to assess the ratings and weights. Fuzzy AHP is utilized to calculate the weights of the evaluation criteria; then, the rankings of alternatives are computed based on fuzzy sets theory and TOPSIS. A real world case study is presented to illustrate a potential application of the proposed model.

Jan 1, 2012

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

By R. E. Mclvor

This is an update of an original dissertation on this topic by Lavallee, McIvor and Stolovitch (1992). A step-by-step, technical procedure used to measure and improve the performance of plant grinding circuits was adapted into a training program. ?Systematic Design of Instruction? was applied to: ? Determine if training was a suitable way to deliver this new technology; ? Define the technical content of the program; ? Select program specifications based on learner and context characteristics; ? Design, create and test prototypes of the training modules; and, ? Establish a process for plant implementation. The training program covers numerous skills that are extremely valuable for plant personnel, not only in the grinding area, but also for many other parts of the plant. This paper describes how new skills are brought into the workplace through designed instruction can be an effective alternative to hiring during severe skilled labor shortages.

Jan 1, 2008

By F. Freme

Coal production in the United States reached a record level in 2005, ending the year at 1.03 Gt (1,133.3 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2005 was 19.2 Mt (21.2 million st) higher than the 2004 level of 1 Gt (1,112.1 million st) and surpassed the prior record set in 2001 by 5.1 Mt (5.6 million st). Although total U.S. coal consumption rose in 2005, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sector by 2.2 percent and declined in the other industrial sector, while coking coal consumption decreased slightly.

Jan 1, 2006

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By Paul D. Tomlingson

Editor's note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By Michael Hughes, Paul Bonapace, Harry Charalambu, Stephen Rigbey

Ontario Power Generation is building a 10.4-km water diversion tunnel in Niagara Falls, Canada. The tunnel is a two-pass, cast-in-place prestressed concrete-lined pres-sure tunnel with a nominal internal diameter of 12.7 m. It is mostly situated within the Queenston formation which swells in contact with fresh water and has very aggressive groundwater. Tunneling in this material presents challenges in both design and construction. The tunnel design includes for a membrane to eliminate the potential for rock swelling and to protect the concrete liner from the ground conditions. A unique three-stage Geotechnical Baseline Report (GBR) is being used and is expected to provide an equitable method of dealing with any variations in subsurface conditions.

Jan 1, 2007

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.