Search Documents

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

The introduction of nitro-carbo-nitrate (NCN) blasting agents has been one of the most significant innovations in the explosive industry in the last twenty years. The most commonly used blasting agent is a rather narrowly proportioned mixture by weight of 94% ammonium nitrate (AN) and 6% No. 2 diesel fuel oil (FO) that is generally designated as ANFO. Other formulations have been developed but none of these have been as extensively used as ANFO. The relative safety of the nitro-carbo-nitrate (NCN) blasting agents almost immediately suggested bulk loading techniques to obtain economies in materials handling. The first attempt at bulk handling was to pneumatically load boreholes with ANFO. When the initial experiments were made in 1957, it was apparent that there were three problem areas which needed study to minimize potential hazards. These were: 1. Static Electricity 2. Fumes 3. Safe Handling Procedures Since those early days, considerable work has been performed in evaluating these problem areas and in arriving at procedures and recommendations that would provide the required safety. Despite the relative insensitivity of ANFO type products, all normal practices for the safe handling of explosives should be obselved. Smoking should not be tolerated in the vicinity of blasting agents and misfires should be handled in the same manner as a misfire with a dynamite charge. The purpose of this Technical Report is to discuss the problems of static electricity and fumes and the solutions that have been developed. Safe handling procedures have been discussed by the Bureau of Mines and are specified by various state and local regulations. Since regulations vary from state to state, the local, applicable regulations must be followed within the area of their jurisdiction. General information is contained in a U. S. Bureau of Mines report, IC 8179, "Safety Recommendations for Sensitized Ammonium Nitrate Blasting Agents" (1963).

Jan 1, 1973

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By Bradley V. Nelson

A number of improvements in the ventilation system at the Henderson Mine have been made during the past several years. A key to these improvements was the installation of a computerized monitoring and control system. Employees can determine the status of any of hundreds of devices in seconds through the use of this monitoring system. Mine dewatering pumps, the water treatment system, the ore haulage system, electric power usage as well as other devices are controlled and/or monitored. Ventilation parameters which are monitored include air flow volumes and carbon monoxide as well as the status of main surface fans, mine doors, and ventilation raise doors. Main underground fans are also constantly monitored and can be controlled remotely. These underground fans can be programmed to automatically start and stop to follow work schedules, optimizing air quality while reducing power cost. Mine air heating costs have been reduced by replacing an electrical resistance heating system with a direct fired natural gas heating system at the portal of the ore haulage tunnel.

Jan 1, 1995

By D. H. Y. Tang, S. S. Peng

Three-dimensional finite element modeling (3-D FEM) was performed to analyze the safety factors of stump pillars, 5.5 m x 5.5 m, under a cover of 63 m using the Modified Drucker-Prager Theory. The results showed that they were safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and analyzes the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By R. D. Lama

This paper presents the results of a large scale trial of polycrystalline diamond picks (PDC) on longwalls with particular reference to dust control. Results from fixed position monitoring showed that PDC picks produced less respirable dust than tungsten carbide Point Attack picks. Dust generation at the longwall face was lower by 39 - 43%. Field trials also indicated that the life of a PDC pick to be at least 1460 tonnes/pick.

Jan 1, 1993

By Roshan B. Bhappu

The extraction of gemstones, except for diamonds, continues to be a more or less handpicking type operation all over the world. However, considering the physical properties of gemstones such as density (sp.gr.), color, size, shape, luster, brilliance, reflection of light and the like in contrast to the relatively ‘dull’ physical characterization of the associated gangue minerals, it should be feasible to recover several gemstones using modern mineral processing techniques. This paper illustrates the unique physical characterization of several gemstones and suggests appropriate mineral processing techniques that could be used to recover these precious stones. Special emphasis is placed on the versatility of the Heavy Media Separation (HMS) process for processing of the gemstones. Finally, a few examples of commercially viable operations involved in the recovery of emeralds and rubies are presented.

Jan 1, 2005

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Anthony J. Ranalli, Florentino B. Maestas, Katherine Walton-Day, Richard W. Healy

Water movement and water chemistry were monitored in the unsaturated zone at two sites in fluvial tailings deposits along the Arkansas River near Leadville, Colorado. One of the sites was remediated by the incorporation of lime and biosolids into the soil. Preliminary results, based on data collected during the 11 months following remediation, indicate that differences between the two sites can largely be attributed to heterogeneity of the deposits. Remediation has increased the alkalinity in the upper soil zone, but as of yet, there is no indication that soils at depths greater than 30 cm have been affected.

Jan 1, 2000

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982

By B. Moudgil, M. Bogan

A bench-top centrifuge was used to study the consolidation behavior of phosphatic clays. A mathematical model (based on, first-order kinetics) was developed to describe the relationship between the void ratio (at any time) and the effective stress. The permeability of the sediment as a function of the void ratio is also described. The results of this analysis are then compared to data obtained by other consolidation testing methods. The centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1997

By Stephen Pogorski, Colin R. Phillips, Atika Khan

An optimized counting scheme for a mixture of radon daughters and thoron daughters typical of Ontario mines, developed in a previous study, was experimentally examined under mine conditions. The counting scheme requires a 10 minute sample and 5 1/2 hours counting instead of a 60 minute sample and more than 40 hours counting as required by a previous method. Taking into account the uncertainties associated with concentrations, flowrate and radioactive decay, the precision of the counting scheme was analyzed and found to be on average better than the 40 hour method.

Jan 1, 1981

By Omid Frough, Hossein Changani

Application of Tunnel Boring Machines (TBMs) is one of the main solutions to achieve a safe and high-performance method of construction in hard rock and soft ground tunneling. In order to adequately assess the progress and potential impacts of the tunneling operations with the TBM, it is required to record a series of data during the tunneling and process of the data to evaluate the TBM performance. Applying the right machine parameters during the excavation not only delivers an optimum penetration rate, but also prevents extra downtime due to over excavation or wear of cutting tools. In this paper, the effect of machine and operational parameters on TBM downtimes has been studied and supported with the real examples of TBM operation data.

Dec 1, 2022

By Patricia T. Foley

An analysis of the demand for copper shows a widely varying pattern of end use. For example, copper tube is the most popular material for hot water supply in the US and northern Europe, but galvanized steel is used in Japan and plastics are used in developing countries. In addition to such peculiarities of end use, the demand for copper varies among countries depending on the stage of industrialization and the extent that the copper processing industries are developed. Brazil, with its abundant supplies of bauxite and hydroelectric power, uses aluminun in place of copper wherever possible. South Korea, with its export oriented economy and its advanced custom smelting and fabricating industries, favors copper. Understanding the details of demand in different countries enhances statistical derived forecasts and illustrates potential new markets.

Jan 1, 1986

By M. Ericsson

The extractive industries consist of five major sectors: - Mining equipment and services - Dimensional stone - Industrial minerals - Aggregates - Metal mining These industries produce some finished goods but mostly semi-finished products as they feed into other industrial sectors: Basic metals, fabricated metals, construction, chemicals, dyes and pigments, inorganic chemicals, fertilizers, rubber and plastics and non-metallic mineral products. These are the major down-stream industries in this study. Taken together with the extractive industries they form the mineral resource based cluster. The mineral resource based cluster is a substantial part of the Finnish economy: It employs 211 000 persons, 39% of the number of employees in industry. The cluster?s exports account for 20% of industry exports. Value added is 34% of total value added in industry. Investments reach 35% of total industry investments.

Jan 1, 2003

By Giuseppe Bonifazi

This study examines the problems involved with the control of characteristics of the products resulting from comminution operations. A methodology of investigation based on texture analysis procedures by image processing techniques of the comminution product is proposed. Some examples of applications are considered with particular reference to comminution products of different textural, structural and mechanical characteristics. The advantages and the limites of this method of approach are, indicated, both as regards performance of the investigations and subsequent processing of results.

Jan 1, 1989

By Daniele Martinelli, Rodrigo Winderholler, Daniele Peila

"This paper presents a technical description of an experimental procedure developed for the geotechnical characterization of granular soils conditioned for EPB tunneling using a modified direct shear box. As the main concerning parameters of the conditioned soil mass were their undrained properties, in order to preserve its pseudo-fluid characteristics, a watertight direct shear apparatus was constructed. A comparison between the results obtained under dry, saturated and conditioned conditions is presented. INTRODUCTION EPB shield machines have been used for tunneling excavation in many different types of soils thanks to the use of soil conditioning agents. These modify the properties of the soil into that of a plastic paste, thus permitting the homogeneous flow of the excavated soil from the tunnel face through the bulk chamber, the screw conveyor and finally the conveyor belt. Moreover this technique allows controlling the face pressure and its regulation in the bulk chamber, preventing water inflow when tunneling below the water table. Further advantages are a drop of the cutter head and screw conveyor torque and reduction of the friction between metallic parts and the soil, consequently reducing wear phenomena (Merritt & Mair, 2006; Vinai et al., 2007; Borio et al., 2010; Thewes & Budach, 2010; Herrenknecht et al., 2011; Barbero et al., 2012; Peila, 2014). Several studies have investigated the possibility of conditioning and the chemical materials to be used in different types of soils, mainly subdivided into three groups: cohesionless soils (sand and gravel), silts and clays, and rock masses. This various researches have set up several laboratory procedures for these achievements before and after soil conditioning, as stated in Thewes & Budach (2010) and Peila (2014) (for cohesionless soils), in Thewes & Burger (2005), Hollmann & Thewes (2013), Zumsteg et al.(2012) (for clay), in Peila et al. (2013) and Martinelli et al. (2015a) (for rock mass). Such tests should be simple to execute, reliable and easy to interpret at the in-situ excavation step. The reduction of shear strength is necessary in EPB operations, since it allows an effective transmission of the pressure from the material itself to the front. In some cases the slump is not sufficient to return a reliable result on the shear strength reduction, as in some cases some materials are behaving differently. Therefore this research is aimed to study this aspect more in detail, in order to show the effectiveness of the soil conditioning process on the material to be excavated."

Jan 1, 2016

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By M. S. J. Leary, M. J. McPherson, O&apos

This paper introduces a computer simulation that extends the use of microcomputer systems for mine ventilation planning. The program was developed as part of an ongoing study to produce a simulation model that would determine the optimum duties of a main fan and a booster fan without requiring the trial-and-error runs that are necessary with currently available programs. To use the new program, the user specifies the location of one main fan and one booster fan, and the minimum required airflows in any number of working places. The computer determines the fan duties that will maintain the required airflows at the lowest operating costs without causing undesired recirculation. The methodology of the program and an example showing how it can be applied are presented.

Jan 1, 1990

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993