Search Documents

By M. R. Stokes, A. J. Ross

As a result of higher levels of production and greater depths the underground mining industry in the UK is encountering hotter climates in some workplaces. It is widely known that high heat and humidity in an underground workplace will result in reduced performance and may also seriously impair the health and safety of the workforce. It is therefore of paramount importance that the underground environment can be effectively predicted in order that sound decisions can be made to reduce the effect of climate on working personnel. Over the years numerous computer programs have been developed to predict the climate in underground mines. One such important program, developed by McPherson, is CLlMSlM TM which is a prediction model of heat and mass transfer along a single roadway. This paper describes the development of a computer model, called DRIVE, to predict the climate in single entry drivages. This program incorporates the theory established by McPherson for the development of CLlMSlM TM. This involves the algorithm for unsteady state heat transfer. Throughout the development of DRIVE underground measurements have been taken to correlate the program. DRIVE will predict the changes in psychrometric and thermo- dynamic conditions along the drivage depending on a number of parameters. Firstly, the type of auxiliary ventilation system employed such as forcing, exhausting, overlap. Secondly, the addition of heat and moisture due to autocompression, machinery, strata, fissure water, oxidation, broken rock, fallen rock, refrigeration equipment, lighting, personnel, service water. Thirdly, due to the velocity of the air.

Jan 1, 1997

By Richard Newcomb

It is four years since the seminal study of demand for rapid excavation by the National Academies of Sciences (NAS) and Engineering outlined this technology's opportunities, requirements and significance to the challenges of urbanization and natural resource conservation. The demand study was quite simple. Opportunities were valued at market while requirements to produce new technologies were valued at cost. The significance of new technology in economic terms was measured by the net discounted gains to users over time. The Academy view in 1968 was that these gains, even most modestly estimated, appeared large enough to justify the bill for research proposed by that Committee (1). In 1970 the question of demands became international in what is recognized as the first international experiment in technological policy analysis, terminating in the Advisory Conference on Tunneling of the Organization for Economic Cooperation and Development (OECD)(2). A monumental demand survey formed the basis for its economic assessment. The twenty-two OECD nations also made an impressive attempt to measure the magnitude of existing research and development efforts. In their recommendations periodical statistical demand forecasting and collection of demand data (Recommendation 1) was given central importance for public planning (Recommendation 2), the financing of public construction (Recommendation 3) and the encouragement of technological advance (Recommendation 4). Their program for international cooperation led to OECD's establishment of a Directorate for Environmental Affairs, and influenced the organization of the World Environmental Conference meetings now held in Stockholm under United Nations auspices. The OECD Conference was the first example of "an attempt to apply the concept of technological policy analysis to a 'civilian' technology having potentially

Jan 1, 1997

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By C. Bazin, B. Girard

The application of time series analysis techniques to plant data provides a method for examining and modeling the behavior of operators during the operation of furnaces for the reduction of ilmenite concentrate. The obtained model is used to assess the consistency of actions carried out by the operators and to review and improve the training procedures.

Jan 1, 1996

By Robert A. Haney, Richard T. Stoltz

In July, 1988, the Mine Safety and Health Administration (MSHA) Advisory Committee on Standards and Regulations for Diesel-Powered Equipment in Underground Coal Mines recommended that the Secretary of Labor set in motion a mechanism whereby a diesel particulate standard can be set. Prerequisite to establishing a standard would be the development and evaluation of instrumentation to measure diesel particulate. In response, the Mine Safety and Health Administration, Dust Division, has been evaluating instrumentation that can be used to determine diesel particulate levels in underground mines. This instrumentation employs the principle of impaction to separate particles by size, thereby, separating the diesel and nondiesel particulate. Separation of the particulate by size was chosen because diesel particulate is generally less than 1.0 micrometer in size. No other methods have been developed to successfully distinguish between the coal and diesel particulate. MSHA developed an impactor that is inexpensive and compatible with existing pumps and filter holders. The instrumentation evaluation has primarily focused on the repeatability and performance of several personal dust samplers. The samplers tested include the Sierra-Andersen Model 298 personal impactor and MSHA developed personal impactor. The MSHA impactor is inexpensive and compatible with the existing pumps and filter holders. In addition to evaluating the precision and performance of these instruments, tests have been conducted to determine background levels of submicron particulate in nondieselized coal mines and to measure the submicron particulate content in dieselized coal mines. Tests were conducted in coal mines where diesel equipment was used only in outby areas and also in coal mines where diesel equipment was used for face haulage. This paper describes the results of the tests and provides a description of the instrument at ion used to conduct the tests.

Jan 1, 1989

By Jr. Smith

Industrial minerals are just other rocks, except for the unique characteristics that make them useful in an industrial process. There is not a ready market for this type mineral and one or more uses must be developed to sustain production. The name "olivine" is a generic term used to indicate a group of orthosilicate minerals in a solid solution series, with forsterite (Mg2SiO4) and fayalite (Fe2SiO4) as endpoints. Since neither is found alone in nature, the mineral is always a combination of the two. The commercial deposits are high in magnesium and on the high end of the melting scale in the series. The name comes from the olive-green color.

Jan 1, 1992

By R. J. Lutton

The suitability of large-stone materials continues to present occasional problems in US construction. Distinctive modes of rock deterioration cracking, spalling, delaminating. disaggregating, disintegrating, and dissolving help to distinguish causes of deterioration. Design requirements, costs, and environmental factors remain critical to performance. The rating of material quality from superior hypes such as granite to marginal types such as conglomerate is too simplistic but may be useful in a preliminary way. Regardless, the market is dominated by limestone/dolomite material types because of their widespread availability. Certain tests that have been standardized are widely accepted and used for evaluating stone as riprap and armor. These tests are adapted from those used extensively for concrete aggregate; they explore the resistance of the rock to destructive processes such as abrasion, freeze-thaw, and wet-dry environmental attack. The field evaluation of the rock source is often as important as testing. Important limitations imposed by natural jointing and variations of bedding are documented in this manner. The field examination also supports the testing by estimating how much of the quarry is rep¬resented by each of the samples to be tested. Finally, quarrying and processing methods and transportation are carefully considered in regard to stone quality, average size, size gradation, and cost.

Jan 1, 1990

By P. L. Webster, S. D. Thompson

The Coal Mine Belt Capacity Simulator (CMBCS) was originally developed to provide an improved belt capacity simulation through more detailed, flexible and realistic modeling of belt loading. While this model offered improved capacity design for conveyor belts and surge bins, it lacked the capability to simulate some key protection and segregation applications for bunkers. Recently, CMBCS was extended so that these latter bunker applications could be considered. In addition, a fear minor extensions were made to improve the model's flexibility and of efficiency. These various extensions and the steps taken to verify and validate them are described. The associated modifications in the model's input and output as well as the model's current requirements and availability are also discussed.

Jan 1, 1992

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By B. K. Mishra, R. K. Rajamani

A numerical method known as the discrete element method (DEM) is used to track the motion of individual balls in large-diameter ball mills. As a result, the en masse motion of the charge, force distribution, fall-height distribution, and energy distribution emerges from the simulation. Hence, it is possible to investigate the effect of mill diameter, liner profile and ball size distribution on the force regime created within the mill. Simulation results for 14-, 16- and 18-ft diameter mills are shown. The proportion of energy lost in high-intensity impacts and sliding ball motion is discussed. The DEM simulation technique opens the way for a closer examination of liner profiles on ball-charge motion.

Jan 1, 1992

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

The minerals industry contributes to the economic growth, prosperity and quality of life of nations, particularly in areas where there might be limited opportunities for employment in other sectors. However, notwithstanding their economic importance, the minerals extraction and processing industries are considered to have significant impacts on the surrounding environment. In recent years many mines have implemented modern monitoring technology and modelling of the monitored environmental parameters to provide scientifically proven indicators about the state of the environment. The flexibility required by the minerals industry to respond dynamically to a changing natural, social and economic environment has become a major consideration. Whilst the notion of continuous improvement is embodied within most environmental management systems, what is now required is a structured audit trail which tracks the flow of resources through the production process to the ultimate environmental impact associated with their consumption, transformation and disposal. Imperial College is coordinating an EC funded project, which is developing a methodology to minimise the ?full life-cycle? impact of metalliferous mining projects, adopting an integrated approach to production and process design, and the costs involved. In order to develop a life cycle assessment (LCA) system that will incorporate different types of data related to the minerals extraction operations, a data inventory was designed and coded in an object-relational database model. The calculation procedures accounting for the input/output balance of the alternative scenarios for mining production, processing, waste disposal, monitoring, and their financial implications are being programmed into a software system. This paper presents the rational and innovative aspects of this work. The methodology developed for the life cycle database is illustrated for the mining production and gaseous emissions components of the system.

Jan 1, 2003

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic in an economic and environmentally safe manner is an important problem facing the mining industry in the United States. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves: • the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), •the selective leaching of the arsenic from the roast calcine with a heated caustic solution, •the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, •the reduction of the residual antimony (collecting the precious metals), •fuming of the metal to form a marketable antimony oxide, and •crucible reduction of the residue to obtain a gold and silver dore. Batch experiments, using synthetic concentrates of stibnite and arsenopyrite, were performed to evaluate the first stage of this process. Variables studied included mixture weight fractions, temperature, gas flow rate, oxygen partial pressure, and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residues were subjected to arsenic leach tests, and the leach solutions were subjected to arsenic and sulfate precipitation tests. Introduction The ability to treat a precious metal ore containing appreciable amounts of antimony and arsenic is dependent upon the characteristics of the ore. For some ores, selective flotation can be used to separate the antimony and arsenic minerals, which are then treated separately. Unfortunately, many ores are not treatable in this way, and the concentrates obtained may contain appreciable contamination (which limits the ability to make acceptable grade antimony products). If we consider the added value of the precious metals in the concentrate, then it is worthwhile to evaluate the potential for new methods to treat these types of concentrates. In addition, the environmental difficulties associated with arsenic disposal must be taken into account in any proposed process. If there is appreciable arsenic present, then it must be either recovered as a marketable product or placed in an insoluble form. The problem addressed in this research program has become increasingly important as the precious metals mining industry is encountering more ores of this type. A large deposit of this type exists in Idaho where the antimony occurs primarily as stibnite, with minor amounts of kermesite and tetrahedrite (Cooper, 1951). The gold appears in association with arsenopyrite with minor amounts of other arsenic minerals. Flotation has been used to obtain an antimony concentrate. The concentrate, however, is contaminated with appreciable amounts of arsenic and also contains precious metals. If the ore or concentrate contains appreciable amounts of base metals, then the recovery process becomes much more difficult. There are a number of other known deposits of this type in Alaska, Canada, Montana and elsewhere. The objective of this research program was to develop a fundamental understanding of the oxidation and leaching chemistry of the arsenic and antimony minerals so that technology may be developed to treat these ores in an economic and environmentally safe manner. Wendt (1949) and Koster and Royer (1940) discussed the possibilities of oxidative roasting of stibnite concentrates containing arsenic. Wendt describes a process used at a smelter in Czechoslovakia (in the 1930s) where roasting was carried out in rotary furnaces at 723° K (500° C). Most of the arsenic was removed as fume, as well as 25% of the antimony. No sulfur dioxide containment was described. The oxide fume from the furnace went to a heated caustic water leach, where the arsenic was preferentially dissolved and then precipitated with calcium chloride as calcium arsenate following solid-liquid separation. The antimony oxide was sold, and the solid oxide discharge from the rotary furnace was sent to a blast furnace where the antimony metal, containing the precious metals, was recovered. The metal was fumed to obtain antimony oxide, and the precious metals were left in the residue and collected with copper. The copper

Jan 1, 1994

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002