Search Documents

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986

By Harold L. Kike

Until recently sulphur uses were so broadly based that economists used sulphur consumption to measure industrial activity. However, sulphur use patterns are changing and the manufacture of phosphate fertilizers presently accounts for approximately 65% of the world's sulphur consumption compared with only 25% in 1960. This has encouraged the development of new agricultural and industrial uses for sulphur. Major emphasis has been placed on its use as a fertilizer and in the manufacture of paving materials, specialty concretes and coatings. Some of these uses could have a significant impact on future sulphur usage.

Jan 1, 1986

By W. Swisterski, G. Romaniszyn, S. A. Lukasiewicz

The present paper analyzes the motion of a particle of material in a horizontaly rotating tumbling mill. The sliding of the particle under action of dynamic and friction forces and its free flight fall are analyzed. It was found that mechanism of free-fall occurs at supercritical rotations of the mill.

Jan 1, 1991

By J. L. Fuller, N. A. Abdel-Khalek

This paper contains a brief summary of design descriptions and generally accepted designations for longwall ventilation systems. Various ventilation systems for longwalls developed using single-entry and multiple- entry systems are discussed. Design considerations specific to longwall mining are included.

Jan 1, 1991

By John C. Edwards, Robert C. Bates

Results are given of a mathematical study by Bureau of Mines personnel of overpressurization ventilation effects in underground uranium mines. The mathematics and computer codes make it possible to analyze many facets of transient and steady-state radon diffusion with Darcy flow. Rapid changes in radon flux occur after imposing a pressure differential across the model. Flux into the model mine drops to near zero and then increases to the steady-state level, while the sink flux increases rapidly and then drops slightly to the steady-state level. Magnitudes of mine flux decreases and sink flux increases are dependent upon the distance from the mine to sink, permeability, and amount of overpressure. Current work on more complex models is also described.

Jan 1, 1981

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By R. W. Hughes, R. Koopmans

This paper investigates the effect of varying stress levels on the determination of deformation moduli and examines the sensitivity of the borehole dilatometer in measuring rock mass scale features and its ability to represent rock mass characteristics. Cubical blocks of sandstone, limestone and granite were tested in the laboratory under triaxial stress conditions. Field programs were conducted in both granite and sandstone rock masses surrounding underground openings. The dilatometer's zone of influence was determined by conducting tests within an instrumented concrete cylinder and by performing a finite element analysis. Laboratory and field results suggest that the deformation modulus of a rock mass can be substantially affected by the stress field and that the borehole dilatometer is sensitive enough to profile deformation moduli as dictated by the in situ rock mass characteristics.

Jan 1, 1986

By Palmer C. Sweet

Kyanite. andalusite, and sillimanite are anhydrous aluminum silicate minerals, and they have the same chemical formula, Al2SiO3. Dumortierite and topaz are also classified as aluminum silicates although they contain boron and fluorine respectively. Mullite (a rare mineral named for its discovery site, the Scottish island of Mull) is produced when kyanite, andalusite, or sillimanite are heated. Synthetic mullite, also classified as an aluminum silicate, is formed by melting alumina and silica, bauxite, and kaolin or alumina, kaolin, and kyanite, depending on the type of synthetic mullite desired. These materials are either sintered in rotary, periodic, or tunnel kilns, or fused in an electric arc furnace. The world's largest producer of kyanite is the United States. Domestic kyanite is presently produced from one company at two sites in Virginia; Kyanite Mining Corporation mines kyanite from Willis Mountain and adjacent East Ridge in Buckingham County in the central Piedmont province of Virginia. Internationally, kymite is produced in Australia, Brazil, India, Kenya, Sweden, and Zimbabwe; the former USSR also produces kyanite (Fig. 1). Andalusite is produced by Piedmont Minerals Company, Inc. in the Piedmont province near Hillsborough, NC. Andalusite is also produced in France, India, the Republic of South Africa, and Spain (Fig. 1). Sillimanite is produced in Australia, Brazil, India, Spain, and the Republic of South Africa; the former USSR is also thought to be a major producer (Fig. 1). Some of the countries produce only for domestic use. Synthetic mullite, made by sintering and by electric arc fusion, is produced by Mulcoa (Mullite Company of America) in Andersonville, GA, and by Washington Mills Electro Minerals Corporation in Niagara Falls, NY. Annual world production of kyanite, andalusite, sillimanite, and synthetic mullite is approximately 672 727 tons (Potter, 1988). GEOLOGY Mineralogy Kyanite is a blue to light-green, triclinic mineral that occurs in long, thin-bladed crystals and crystalline aggregates in gneiss, schist, and pegmatites. The mineral has a hardness of 5 parallel to the long axis of the crystal and a hardness of 7 across the crystal. Andalusite is a yellow, brown, green, or red orthorhombic mineral that occurs in thick, almost square prisms in schist, gneiss, and hornfels. Gem quality andalusite exhibits a strong pleochroism; brownish-green in one direction and brownish-red perpendicular to it. Andalusite also occurs in placer concentrations where it has weathered out of rock. Sillimanite is a brown, pale-green, gray, or white orthorhombic mineral that occurs in long, slender, needlelike crystals in schist and gneiss. Chemical and Physical Properties Chemical and physical properties of kyanite, andalusite, and sillimanite are noted in Table 1. Kyanite is the only mineral that irreversibly expands when heated (calcined to produce mullite) and may offset the shrinkage of most ceramic or refractory ingredients when heated.

Jan 1, 1994

By Malcolm J. McPherson

The highest recorded loss of life due to the collapse of mine workings occurred at the Coalbrook North Colliery in South Africa on 21st January, 1960. A total of 437 persons died when bord and pillar workings collapsed over an area exceeding one square mile The whole mass of strata from the 470 ft (143 m) deep seam to the surface being affected. Although the Coalbrook disaster was unique in its scale the problem of pillar failure, particularly in old workings, is by no means uncommon nor confined to recent history. Indeed, the collapse of large pillared areas was a regular feature of mining in the north of England in the early part of the nineteenth century. When a section of underground workings collapses, the air under the descending roof is compressed very rapidly. The pressurised air is dissipated subsequently at a rate governed by the leakage paths available. If the collapsing area is small, such as the case of a local fall of roof, then there will be little danger of an air blast. If, however, an extensive area collapses suddenly then the rapid compression of air will give rise to a pressure shock wave that will be transmitted through the remaining workings as an air blast. If worked out areas are connected to current workings via unstopped airways an air blast caused by pillar failure in the old workings will be extremely hazardous to personne1 and may cause extensive damage to equipment, perhaps even reaching to surface plant. At Coalbrook, the air blast blew out a wall in the surface fan house. Areas that are considered liable to sudden collapse may be isolated from current workings by the construction of stoppings. However, such stoppings must be capable of withstanding the 'hammerblow' effect of peak air pressures developed during the collapse. The work described in this paper was undertaken in order to determine the maximum air pressures that stoppings must withstand during a major pillar failure. The result has been a method of establishing peak air pressures that is quick and simple to use. Readers who are concerned primarily with the practical application of the method are advised to turn directly to the last main section of the paper.

Jan 1, 1980

By Bernard P, Lhoumaud E, Gunzburger Y, Conin M, De Santis F, Kinscher J

Seismic repeaters are commonly observed in natural fault zones dominated by slow aseismic motion. The corresponding seismic signal, characterized by highly similar wave forms, is usually interpreted as the repeating ruptures of locked asperities on fault planes (“patches of higher roughness”), loaded by a-seismically slipping areas (“creeping areas”) (Chen & Lapusta 2009; Bourouis & Bernard 2007). Only very few occurrences of seismic repeaters have been reported in underground mines, where these phenomena are rather unexpected since the stress state and the seismic wave propagation continuously evolve with the advancing excavation front (Kinscher et al., 2020). A recent study based on a local seismic network installed in the underground mine of Garpenberg, Sweden, has shown that seismic repeaters and multiplets represent the main part of the total released seismic energy (magnitude of seismic events: -2 < M <1, on moment magnitude scale), with some seismic families being active during several months to years. It is suggested that repeaters are linked to aseismic slip on pre-existing talc-filled fractures, induced by the excavation, and loading of asperities. These results imply that part of redistribution of stresses in the mine is due to aseismic slip, which might explain the observed distant and delayed seismicity.

Apr 26, 2022

By Helen Leung, Colin R. Phillips

The performance of personal alpha dosimeters in mixed radon daughter and thoron daughter atmospheres in Ontario uranium mines is described together with monitoring developments which enable the radon daughter working level to be determined separately. The theoretical bases for continuous and integrated working level measurements based on individual and gross counts are presented in terms of the weighting factor for combining the thoron daughter working level with the radon daughter working level, and in terms of the in-growth time of the air. Implications for the determination of working level in the presence of thoron daughters are discussed.

Jan 1, 1981

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By D. R. Zeni

Current mine development requires the safe, &apos;expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By Andrew Neale, Ari Supomo, Mike Mular, Rob Perry

A method is presented to measure and correct the performance of regulatory control loops. Freeport Indonesia treats over 220,000 dmtpd of copper-gold ore in a complex of four concentrators. More than 400 regulatory control loops are implemented throughout the operation. The performance of each loop is quantified by an index based on its time in automatic, the deviation of the measurement from the setpoint and a metallurgical assessment of its impact on overall plant operation. Index values are recorded in a plant-wide data acquisition system and analyzed to produce a report of loops requiring attention. Loop statistics are analyzed to show if the problems can be corrected with tuning. The practical application, benefits, management and staffing requirements of this method are discussed.

Jan 1, 2000

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By D. G. Krige

Sampling data from large mined out areas of, existing Witwatersrand mines is split into areas accepted as &apos;mines&apos; and used to provide for each mine the equivalent of a number of sets of borehole values as well as the follow-up &apos;actual&apos; value. This data is used to establish the spatial structures on a macro scale between &apos;mines&apos; for grade as well as variance and the suitability of the three-parameter lognormal model Is tested for the borehole and &apos;mine&apos; frequency distributions. A comprehensive range of borehole valuation techniques is then applied to a large number of borehole sets on an individual mine basis. The results for each technique are then compared with the corresponding follow-up &apos;actual&apos; values for these mines. After normalisation via the three- parameter lognormal model the estimates are also correlated with the &apos;actuals&apos; to define any conditional biasses and to establish the observed error distributions and error variances of the estimates. On this basis the various techniques are rated for their relative efficiencies and the significance of the advantages gained.

Jan 1, 1992

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson&apos;s equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993