Search Documents

By Vanessa M. Torres

Diagnostic leaching tests provide a good indication of gold deportation in its various occurrence phases. With the results of these tests, possible flowsheets for difficult ore treatment can be established for further evaluation and plant operation can be optimized. The use of this technique can be extended, including heap leach evaluation and complex copper-gold ores. The results on the use of diagnostic leaching tests in gold ores from Companhia Vale do Rio Doce (CVRD) are presented and discussed, as well as the methodology to select steps and interpret results used at CVRD Technology Center (Sutec).

Jan 1, 1998

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016

By J. A. Frew, G. I. Orrock, R. M. Glen

The zinc flotation circuit was sampled to provide sized information on its metallurgical performance. A good balance was obtained and the roughing, scavenging, cleaning and regrind sections were assessed. Substantial losses of sphalerite occurred in all sizes. The limitations were poor recovery in the cleaning section which resulted in substantial recycling of 15-30µm sphalerite and iron sulphides, and inability to float +38µm sphalerite in the roughers. Regrinding increased sphalerite recovery by 7% with no loss in grade. Liberation measurements enabled balances for six size fractions to be calculated and the role of liberation on the metallurgical performance was assessed.

Jan 1, 1993

By N. Powell, C. F. Spollen, B. A. Wills

A discussion of the practicalities of carrying out a material balance using simple nodal sensitivity analysis is given. The calculation of the errors involved is reviewed and the concept of co-variance examined through computer simulation. The use of co-variances in such calculations is shown to be practically insignificant. The method proves to be rapid and relatively accurate provided the circuit topology is correct.

Jan 1, 1991

By R. M. Barker

The historic Getchell property is currently being mined from the Getchell Main Underground workings, a foot wall extension of the Getchell open pit deposits along the Getchell fault. Drift-and-fill techniques are used to extract the ore through a ramp access. The adjacent Turquoise Ridge deposit is currently under development via two vertical shafts. Together, the two mines will continue to provide feed to the Getchell's 3,200 tpd mill/autoclave circuit, taking Getchell Gold from its current production rate of 200,000 ounces (Au) per annum, to over 400,000 ounces (Au) per annum by 1999.

Jan 1, 1997

By Ronald D. Hill

Acid mine drainage is the result of the oxidation of pyrite and similar iron sulfide material and the release of iron and sulfuric acid into the environment. In addition to the acid water flowing from underground and surface mines, spoil materials in surface mines are acidic and will not support good vegetative growth; thus erosion is a major problem. Lime and limestone are the major neutralizing agents used to treat these acidic conditions. Lime is the reagent preferred by industry for treating acid discharges, although a few companies use limestone. Agricultural lime- stone is used to "sweeten" acid spoils.

Jan 1, 1974

By K. E. Brown, T. D. Murphy

At Monterey Coal's No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By P. L. Padgett, J. C. Hower

Five coals blended at a Midwestern United States power station were subjected to detailed analysis of their Hardgrove grindability. The coals, representing four distinct coal beds, are a low-sulfur, high-volatile A bituminous Upper Elkhorn No. 3 coal (Pike County, Kentucky); a medium-sulfur, high-volatile A bituminous Pittsburgh coal (southwestern Pennsylvania); a low-sulfur, subbituminous coal from the northern Powder River Basin (Montana); and two low-sulfur, subbituminous Wyodak coals from two different mines located in the eastern Powder River Basin (Campbell County, Wyoming). All samples that were processed in the Hardgrove grindability tests were also analyzed for their maceral and microlithotype content. The high-vitrinite Pittsburgh coal and the relatively petrographically complex Upper Elkhorn No. 3 coal exhibited different grindability behavior. The petrographic compositions of the Pittsburgh raw feed, the 16 x 30-mesh fraction (HG! test fraction) and the -30-mesh fraction (HGI test reject) are similar, suggesting that the HGI test fraction typifies the whole feed. The eastern Kentucky test sample is not as representative of the whole feed, with the HGI test fraction having lower vitrinite amounts than the rejected -30-mesh fraction. The Powder River Basin coals are high in vitrinite content and show behavior similar to the Pittsburgh coal.

Jan 1, 1998

By W. H. Su, S. S. Peng

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in an underground coal mine located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses, were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1987

By V. Rajaram, D. P. O’Connor, L. Sakamoto

In 1988, the Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project. This was prompted by numerous complaints from residents in the vicinity of the project and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods used by two major contractors driving 20 km (12.5 miles) of tunnel, and drilling more than 36 shafts under this restrictive specification. The impacts are detailed on design, construction, schedule, cost and the environment.

Jan 1, 1993

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By Leonid P. Ni, Askar M. Kunayev

It is well known that processing of the high-silicon bauxites for obtaining alumina by the hydrochemical Bayer process is irrational due to the significant losses of alumina and alkali with red mud. The main source of losses of the mentioned compounds under the conditions of leaching by the Bayer process is the formation of difficultly soluble sodium alumosilicate of the composition Na20 .Al203, 2Si02 . n H20. A conventional method of an extra recovery of alumina as well as of regeneration of alkali out of red mud is the high-temperature sintering of the latter with soda and limestone with the subsequent leaching of sodium aluminate from the sinter by water or soda solution. A sequential version of the Bayer-sintering flow chart recommended for the prosessing of bauxites with an increased content of silica is based on this method. However, the sintering method is not the only alkaline method allowing to make an extra recovery of alumina likewise of alkali from red mud. Our investigations showed/I/, that the components mentioned can be recovered by a pure hydrochemical method of treating red mud with concentrated alkaline solutions, with lime (Ca0) being present, that was earlier succesfully used in the development of the hydrochemical method of processing nepheline rocks/2/. The possibility of extracting alumina and alkali from red mud is based on the reactions which can be schematically represented in the following way:

Jan 1, 1984

By Robert J. Timko, Edward D. Thimons, Robert L. Derick

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high- expansion foam. As a result of several strategic decisions, the fire appeared to be held in check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed. This paper recounts activities from the discovery of the fire to the initial reentry of the sealed mine including location of the fire, the decisions made to best combat it, and the steps taken to rapidly and securely seal the mine when this became necessary. The mine operator requested the Bureau's assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals. This report describes how samples were taken and what gases were analyzed. In addition, this work describes the initial exploration of the sealed mine by personnel using oxygen breathing apparatus.

Jan 1, 1987

By Moussa Wone, William Levy, Christopher Caruso, Zachary Spera, Thomas Hennings, Richard Stacy Kinchen, PE Joel Kantola

"Owners constructing new combined sewer overflow (CSO) systems increasingly seek to have project design lives of 100 or more years in response to the growing size, complexity, and cost to construct and operate these systems. However, a codified and universally accepted approach to achieving this goal in the United States does not currently exist since service life prediction is a relatively new technical field. This paper discusses how the 100-year design life requirement was met for the design of tunnels, drop shafts, and diversion structures in the DC Clean Rivers Program (DCCRP). The authors identify some commonly referenced publications, present the testing framework used by the program manager to characterize the CSOs, review the design criteria used to guide the 100-year design life development, and establish guidelines to be considered by program managers and designers when implementing similar extended design life requirements in other CSO control programs.INTRODUCTIONLike many older cities in the United States, the sewer system in the District of Columbia consists of both combined sewers and separate sanitary sewers. When the capacity of a combined sewer is exceeded during storm events, the excess flow, which is a mixture of sewage and storm water runoff, is discharged to the District’s receiving water bodies (Anacostia River, Potomac River, and Rock Creek) and tributaries through outfall structures. This excess discharge during storm events is called a combined sewer overflow or CSO. A total of 53 CSO outfalls for the combined sewer system are listed in DC Water’s National Pollutant Discharge Elimination System (NPDES) Permit issued by the U.S. Environmental Protection Agency (EPA). The DC Clean Rivers Program (DCCRP) will reduce the number of CSO outfalls into the Potomac and Anacostia Rivers and decrease flooding in DC neighborhoods during extreme rain events by capturing, storing, and conveying diverted CSOs to the Blue Plains Advanced Wastewater Treatment Plant."

Jan 1, 2016

By Walter J. Johnson, Robert L. Chufo

A unique non-contracting coal thickness measurement technique has been developed to measure both the dielectric constant and thickness of a coal seam as part of a sensor array supporting an autonomous coal mining machine. The sensor measures the reflection of an electromagnetic signal from the coal/shale interface. Underground measurements of coal 6- in thick with a dielectric constant of 4 have been confirmed. Measurements were also made of a 31-in thick coal pillar for application of the sensor to highwall mining. The electromagnetic measurement technique, the data reduction process and field test experience will be presented.

Jan 1, 1992

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003