Search Documents

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By J. Du, V. Shukla, C. R. Kumar, U. Shivangi, D. P. Chakraborty

During the processing of iron ores, a large quantity of low-grade tailings containing abundant iron values in fine particle size range is produced. Due to the increasing demand in the high-grade ores for metallurgical operations and the stringent environmental conditions imposed on mining activity, it is essential to utilise the waste tailing pond slimes. Recovery of iron values from these tailing ponds not only enhances the life of the existing operating mines, but also enables achievement of a sustainable process. Iron ore tailing/slime (-150 μm) is produced after scrubbing and wet screening of a low-grade iron ore. Tailing beneficiation of iron ore has been addressed either by flotation or wet high intensity high gradient separation. The present paper aims to recover iron values from discarded slime containing assay ~56% Fe, ~6.5% SiO2, and ~7.0% Al2O3 from the Noamundi processing plant by using a high gradient magnetic separator (HGMS). In this process, tailings are effectively processed with a vertical pulsating high gradient magnetic separator to produce a relatively high-grade iron concentrate. The results of investigation indicate that this novel process is capable of producing an iron concentrate assaying ~ 60% Fe and ~3.25% alumina with a yield of ~55 % on weight basis and recover > 65 % iron bearing particles from the tailings. More importantly, the corresponding tailing contained ~45% Fe. It was concluded that this novel process may be effectively used to recover iron values from low-grade hematite tailings. Keywords: Iron ore slime, Fe recovery, HGMS, yield, Noamundi

Jan 1, 2020

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By M. Izadi Yazdan-Abadi, S. H. Amiri, M. Ramezanizadeh, M. Bazmandeh

Iron ore concentrate is used as the fresh feed of pelletising plants. The green pellet properties depend on iron concentrate characteristics such as particle size distribution (PSD), specific surface area (Blaine value), iron grade, moisture content and grinding methods. The grinding methods affects particle size distribution and Blaine value. To find out the effects of grinding methods on pelletising process, green pellets were produced with concentrates that were reground by means of HPGR (high pressure grinding rolls) and ball mill. The Blaine values of ground concentrates in both types of milling were approximately 1400, 1600 and 1800 cm2/gr. The results of green pelletising tests on a pilot plant scale showed that at the same Blaine values, drop numbers of green pellets produced by ground concentrate inside HPGR were higher than the green pellets produced by ground concentrate inside a ball mill. Also, reground concentrates by means of HPGR, in comparison with ball mill, caused the production of green pellets, at higher wet and dry compression strengths. As a result, it was found that preparing the pelletising feed by means of HPGR led to more positive effects on the properties of green pellets. Keywords: Ball mill, HPGR, green pellet, drop number, wet and dry compression strengths

Jan 1, 2020

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By Z. Zhang, J. Niu, H. Wang, Y. Xu, J. Shi

Tribo-electrostatic separation is a promising method for effectively utiliing low-grade magnesite resources by removing quartz and improving the grade of magnesite. To determine the chargeto- mass ratios of pure magnesite and quartz, a triboelectric measurement system was employed, and a laboratory tribo-electrostatic separation system was used to separate low-grade magnesite. The results showed that the maximum difference in charge-to-mass ratio between pure magnesite and quartz particles was observed after friction with polyvinyl chloride. The grade and recovery of magnesite increased with temperature and initially increased with increasing voltage, feed rate, and air flowrate before gradually decreasing. The optimal conditions resulted in a concentrate with 46.91% MgO content and 77.36% recovery, while the quartz content decreased from 7.02% to 1.95%. These experimental results demonstrate the effectiveness and potential of tribo-electrostatic separation in removing quartz and upgrading magnesite.

Apr 14, 2024

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By C. Dorfling, M. Tadie, S. Grobbelaar

The physicochemical properties of the complex electrolytes used in direct copper electrowinning are an important consideration for the development of a high-fidelity model of the process. Direct electrowinning electrolytes typically contain a high background of metallic impurities. The effect of metallic ions on the properties and accompanying change in the limiting-current density for copper reduction have been the subject of several studies. Although various empirical correlations have been published for describing the physicochemical properties of electrowinning electrolytes, the correlations are only applicable to a limited range of conditions and cannot be extrapolated without further validation. Consequently, in this paper we validated existing physicochemical property correlations for the full range of operating conditions applicable to direct copper electrowinning and developed a new correlation for predicting the associated limitingcurrent density for copper deposition. Following, we evaluated the benefit of using the validated correlations as a component of a dynamic electrowinning model.

Jan 1, 2023

By D. Weijie, S. Kai, Y. Hu, X. Ning, M. Shiyi, W. Junpeng, Z. Guihong, L. Xianjie

Flotation is one of the most important processes in the copper production industry. The copper grade in the concentrate is a pivotal indicator of the flotation process performance. However, it is difficult to achieve real-time measurement through hardware sensors. Based on the production data provided by an industrial operation, a novel soft sensor based on multi-layer perceptron (MLP) is proposed for effective monitoring of this pivotal indicator. The proposed soft sensor uses the nonnegative garrote (NNG) to perform global variable selection for MLP, while a local search (LS) approach is incorporated to improve the model presented by NNG. Simulation results show that the proposed algorithm has higher prediction accuracy and better model simplicity than other algorithms. Furthermore, the variables selected are consistent with the field experience, and the developed model can provide reference of feedback control for the optimisation of the process. Keywords: Flotation process of copper ore, nonnegative garrote, local search, soft sensor, multi-layer perceptron

Jan 1, 2020

By G. Howell, J. Wates, A. Coetzee, C. J. MacRobert

The Global Industry Standard on Tailings Management (GISTM) requires mining companies to make four key appointments as part of their tailings management structure. These four positions are an Accountable Executive with policymaking responsibilities, a Responsible Tailings Facility Engineer with operational responsibility, an Engineer of Record to ensure facilities are designed, operated, and closed safely, and an Independent Tailings Review Board to assess safety drivers regularly. Little guidance on the traits of these individuals is available in a South African context. Consequently, the tailings community of practice was surveyed to develop a table of ideal competencies and establish the flexibility in meeting these traits.

Jun 2, 2022