Search Documents

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By Julie Mitchell, Robert King, Len Eros

The Bureau of Mines has studied the Deserado Mine computerized monitoring and control system, located in Rangely, Colorado, to acquire knowledge about the overall costs and benefits of mine monitoring systems. The Deserado system is a complex system monitoring environmental parameters, electrical power, and operation of all mine equipment, and controlling the entire conveyor haul age system. This paper discusses the evaluation of the Deserado monitoring system from initial design through system installation and operation. It also examines the costs, benefits, and performance of the monitoring system.

By J. L. Konchesky

The Bureau of Mines investigated the main reactions of coal gasification by steam. Coal (minus 70 mesh)-water slurry was fed into a laboratory-scale tube-coil gasifier to show the effects of residence time (0.6 to 1.1 sec), steam-coal ratio (2 to 11 lb/lb), and temperature (1,600° to 1,900° F), at about 1-1/2 atm. Devolatilization was very rapid: about 70 pet of the coal's volatile matter evolved within 0.6 sec at about 1,600° F; temperature increase released more volatile matter until about 95 pct was driven off at 1,900° F. Devolatilization was not increased by raising steam concentrations and was only slightly increased by extending residence time. Below 1,600° F, there was no evidence of the steam-carbon reaction, but at 1,900° F more than 80 pct of the coal's fixed carbon was converted to gas; the conversion was increased Significantly by increased residence time and steam concentration. The water-gas shift reaction occurred simultaneously with devolatilization, and the steam-carbon reaction, approaching equilibrium with increased residence time and temperature and decreased steam concentration.

Jan 1, 1969

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government's revenue.

Jan 1, 1986

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974

Coal miners, especially roof bolter and continuous miner operators, work in a hazardous underground environment where they are often exposed to poor roof conditions. Nearly 500 rock fall injuries are reported each year, and 99% of them are caused by rocks falling from between the roof bolts. These loose rocks that injure miners are usually just a few inches thick, but on average weigh 280 pounds. NIOSH has found that most rock fall injuries can be prevented by installing roof screen during the bolting cycle. Roof screen is a sheet made of steel wires in a grid pattern. When screen is bolted up against the mine roof, it provides far more coverage than any common surface control used in the mines today. Because more mine roof is covered, there is less chance that a rock will fall and injure a miner. The facts about roof screen are shown in the new NIOSH video entitled “Make It Safer With Roof Screen.” Using extensive underground footage, the 7-minute video shows how well screen keeps loose rock from falling in difficult roof conditions. Techniques for installing screen from both outside-controlled and walk-thru roof bolting machines are shown. The video also provides safe handling tips, best practices, and information about machine technology that can greatly improve material handling. Throughout the video, a coal mine safety manager and a shift foreman talk about the tremendous difference that roof screen has made at their mines. An instructional booklet supplements the video with additional information. It presents compelling data from mines that have practically eliminated rock fall injuries with a roof screening program. Other sections of the booklet discuss in greater detail roof screen installation, tips for manual screen handling, a material handling system for roof screen, and use of the personal bolter screen, which can be easily handled by one person. Screen specification and custom ordering are described, including the sizes of screen, grid sizes, reinforcing (indicator) wires, edge cut options, and screen strength. A list of additional sources of information is also provided. Nearly every mine eventually encounters poor roof. Screen is one of the most powerful control techniques available. This new video will help make mine managers aware of screen, and it can help them in developing a roof screen installation program. It also serves as an information source and teaching tool for safety managers and trainers. The video can easily be integrated into new miner training programs or annual refresher training.

Mar 1, 2005

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By Fred N. Kissell, Maurice Deul, T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By R. E. Stiles

The modified perchloric--EDTA method devised by the Bureau of Mines for the determination of copper in high-grade samples gives results that are more precise and more accurate than those from the classical sulfuric-iodometric method. Although the perchloric--EDTA method is more costly than the conventional method, the savings in time alone largely offsets this difference. Specifically, the modifications wade in the more conventional procedure comprise (1) use of perchloric acid instead of sulfuric acid for dissolution of copper minerals, (2) precipitation of copper as copper sulfide from dilute perchloric acid solution, (3) wet oxidation and dissolution of the precipitated copper sulfide, (4) use of larger amounts of indicator than those employed in the Schwarzenbach method of titrating low-tenor copper solutions with disodium ethylenedinitri10-tetraacetate and murexide indicator, and (5) use of refrigeration to partially stabilize aqueous solutions of the indicator.

Jan 1, 1966

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974