Search Documents

By G. S. Rice

The recommendations of the Bureau of Mines on rock-dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions,5 approved by the. American Engineering Standards Committee,6 December 30, 1925 It is specified that the dust to be used is of a size that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch.

Jan 1, 1930

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult, longstanding engineering problems associated with coal mining is the catastrophic failure of cog mine structures known as bumps. For more than 70 years, researchers and practitioners have assembled a wealth of technical information on coal bumps in an attempt to understand and control them. However, many technical issues raised long ago are still being debated today. This paper examines past experiences and recognizes achievements in the realm of coal bumps. U.S. Bureau of Mines (USBM) researchers collected and analyzed 172 coal bump incident reports and compiled the pertinent statistics into a database. Actual field studied are also discussed. Examination of past experience has shown that there is no one set of defining characteristics that is responsible for coal bumps. In all cases, bumps occur when complex arrangements of geology, stress, and mining conditions interact to interfere with the orderly dissipation of stress. However, it is evident from the database that a tremendous reservoir of knowledge has been established from past experience that has unquestionably limited the severity of coal mine bumps in the United States.

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By D. C. Fleck

This report describes a method of using sodium for reducing titanium tetrachloride, developed at Boulder City, Nev., as part of the Federal Bureau of Mines effort to improve the extractive metallurgy of titanium. Finely divided titanium metal, titanium lower chlorides, or a mixture thereof was produced in a continuous operation at temperatures between 105° and 205° C. by the reaction of molten sodium and vaporized titanium tetra-chloride in an agitated bed of finely divided inert solids (powdered sodium chloride or the reaction products). Composition of the product was controlled by varying the relative quantities of sodium and titanium tetrachloride used. A description of the operations and analytical data of the reaction products are given.

Jan 1, 1960

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By H. H. Schrenk

The Bureau of Mines midget impinger dust-sampling apparatus was described first in 1937.4/ Two supplementary reports5/6 were published in 1938. These reports are now out of print. The material published previously is combined in this paper to make information on this device available for distribution. The impinger was developed by the Bureau of Mines in cooperation with the United States Public Health Service in 1922. The underlying principle of this instruments is based on impingement land wetting, of the dust particles by drawing air through a nozzle at high velocity onto a smooth surface under a bubbling column of liquid. The dust particles are retained in the liquid. The apparatus has been used widely and permissible limits of dustiness have teen established in the United States on the basis of results obtained with this device in correlation with medical studies. However, it has been criticized for its bulk, weight, and power requirements.

Jan 1, 1939

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By E. Chin

Bangladesh, whose population probably passed 100 million by yearend, remained one of the poorest countries in the world, with a per capita gross domestic product (GDP) of $126.2 Its only economically significant mineral production was natural gas. A few other minerals or mineral-based commodities were also produced, generally for local consumption. These included cement, clays, nitrogenous fertilizers, limestone, salt, steel, and pilot plant production of ilmenite and rutile. Exploration for oil was a continuing quest, which was hindered by a lack of funding and a hesitancy on the part of foreign petroleum companies to make long-term or expensive exploration commitments. PODUCTION AND TRADE Production of natural gas continued to increase as more use was being made of the abundant gas reserves variously put at between 7 and 16 trillion cubic feet. The main consumers were nitrogenous fertilizer producers and electric powerplants, but other industries were converting to natural gas from imported coal or fuel oil wherever possible.

Jan 1, 1986

By W. S. Landers

Analysis of the size consist of broken coal has been extended in recent years beyond the mere representation of the relative quantities of the various sizes present in a given lot of the material. Fundamental characteristics of the coal related to the process of breakage fix the distribution of sizes, and it has been found by Rosin and Rammler4/ that a relatively simple law-governs this property. Benhett5/ has described a graphical method of expressing the relationship, and by its use considerable simplification in the expression of size distribution is possible.

Jan 1, 1946

By Michael J. Sapko, Eugene M. Bazala, Eric S. Weiss, Kenneth L. Cashdollar

The data presented in this report are the results, to date, of an ongoing Pittsburgh Research Center Disaster5Prevention research program on the explosion hazards associated with blasting operations in noncoal mines. Laboratory and experimental mine tests have shown that oil shale and sulfide ore dusts can be ignited given the proper predispersed dust concentrations, particle size, and kerogen or sulfur content. Methane (CH) gas may also4be present in deep oil shale formations and can pose a significant added hazard to underground blasting operations. The most common explosive used for blasting in oil shale had been ANFO, a combination of ammonium nitrate and fuel oil; blasting in sulfide ore had used ANFO and/or dynamites. Tests conducted at the cannon gallery at Lake Lynn Laboratory near Fair chance, Fayette County, PA, provided a means of evaluating the relative incendivity characteristics of new and existing explosive products. Three explosives—a pumpable emulsion-ANFO blend, a packaged water gel, and an emulsion blasting agent—exhibited low-incendive qualities compared with other more highly incendive products such as ANFO and some dynamites. Based on the data collected during numerous full-scale blasts in oil shale and sulfide ore mines, the low-incendive products significantly reduced or eliminated the ignition hazards while at the same time providing effective fragmentation of the rock. Based on the positive results from the gallery and field testing, low-incendive explosives, coupled with good blasting procedures, show promise in reducing dust and/or gas ignitions associated with blasting operations in oil shale and sulfide ore mining applications.