Search Documents

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Matewan 7-1/2 minute quadrangle in eastern Kentucky was selected as the initial study area. Results indicate that of the original 1,193 million tons of resource in the quadrangle, only 89 million tons (7.5%) are economically recoverable at a cost of $25 per ton or less. At the current production rate of 5.3 million tons per year, this represents only 16.8 years of remaining reserves.

Jan 1, 1993

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

The REL of 1 mg/m3 for respirable coal mine dust does not assure a zero risk for the development of occupational respiratory diseases among all miners exposed during a full working lifetime. Consequently, a medical screening and surveillance program that includes initial and periodic chest X-rays and spirometric examinations is important for the early detection of disease and the prevention of "material impairment of health or functional capacity" [30 USC 8 11(a)(6)(A)]. The medical screening and surveillance program is also useful for disease surveillance, which includes the tracking trends, the setting of prevention and intervention priorities, and the assessment of prevention and intervention efforts. NIOSH encourages both underground and surface coal miners to participate in the medical screening and surveillance program.

Jan 1, 1997

By H. B. Brunot, L. C. IlsLey

The chief object of the Electrical Section of the United States Bureau of Mines is the study of causes and means of preventing accidents resulting from the use of electricity in mines . A large part of this work for the last 20 years has been the inspection and testing of mining equipment under the provisions of schedules which give the minimum requirements considered essential for the safety of equipment intended for use at or near the working faces of dusty or gassy mines . During the first few years of this work , particular attention was paid to the explosionproof features of the various accessories such as motors , controllers , and other parts . The knowledge of the essentials necessary for safe designs of enclosures has since been augmented by field experience and by data obtained in testing a large number and variety of designs . With our present knowledge it would seem that a disproportionate stress was placed on making the various enclosures explosionproof , but not enough thought was given to the danger from wiring and connections outside of explosionproof enclosures . The list of equipment that has met minimum requirements for safety and has been approved as permissible by the Bureau of Mines includes storage - battery locomotives , power trucks , drills , loading machines , conveyors , cutting machines , room hoists , pumps , concrete mixers , and rock-dusting machines . The wiring on some of the machines is comparatively simple and sometimes , except for the trailing cable , may be entirely within the explosionproof enclosures . In general , there is outside wiring between enclosures , and on the larger machines the wiring may be extensive and complicated . In considering the safety of wiring for mining machinery , attention must be given the severe service and unfavorable surroundings imposed by mining conditions . Some of the matters that require consideration are : ground . The lack of care of the exterior wiring to be expected in the average mine . The lack of adequate periodic inspection of the wiring . The absence of adequate facilities for satisfactory inspection and repairs under- The severe conditions of moisture , dirt , mechanical injury , and low voltage encountered in mining service .

Apr 1, 1931

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

 Previous reports of this series/7/8/ presented data on the composi- tion of exhaust gases produced by Diesel engines operating under various conditions possible in underground workings. In all previous experiments, the engines tested were in proper mechanical condition; that is, they were adjusted and maintained in accordance with the manufacturer's instructions. In discussing the results of these tests in relation to the use of Diesel engines underground, the importance of maintaining engines in proper mechanical condition was emphasized, although no data were presented to indicate the effect of engine maladjustments on production of harmful and objectionable constituents of exhaust gas. It is the purpose of this report to present such data and to reemphasize the importance of adequate maintenance for Diesel engines used underground.

Apr 1, 1943

By J. H. Perry, D. W. Houseknecth, C. A. Kertis, A. T. Iannacchione

Major problems facing the development of coal and gas resources of the Hartshorne Coalbeds include the complex distribution of minable and unminable coal, high methane content and bed pressure, faulting, variations in degree of dip, presence of natural gas fields in associated sandstones, and legal problems, caused by local geologic characteris- tics, in identifying gas origin. This Bureau of Mines study provides pertinent geologic information for long-range planning of subsurface coal and gas production from the Hartshorne Coalbeds. Pittsburg, Coal, Hughes, and Atoka Counties, OK, have approximately 1 billion metric tons (1.1 billion short tons) of Hartshorne coal in place. The methane resource of Hartshorne Coalbeds is estimated at 9.2 billion m3 (325 billion ft3) and varies with overburden and rank, These estimates were compiled from gas well density logs, coal-core data, out- crop measurements, abandoned mine maps, and the literature. The Hartshorne Coalbeds represent a valuable coal and gas resource which at present is contributing nothing to coal and gas production. This report discusses potential problems and serves as a reference for future exploration and development work. Recognition of these potential geologically related problems prior to development of this basin will reduce hazards and allow for an economic recovery of these resources.

Jan 1, 1983

By David F. Gearhart, Thomas M. Barczak

This U.S. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (9 compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 1992

By R. S. Olsen

The Bureau of Mines is engaged in a continuing research effort toward the recovery of alumina from kaolinitic clay and other nonbauxitic domestic minerals. Hydrochloric acid extraction of calcined clay is among the acid processes under consideration. Although aluminum is easily leached from calcined clay, the presence of fines and slimes in the leached residue has hindered the application of this and other acid leaching processes. A clay feed preparation method was therefore developed that eliminated the slimy nature and the separation problems normally associated with leached clay residues. The preparation process consists of crushing the raw clay to minus 20 mesh, dampening the crushed clay with a fine water mist while tumbling on a rotating disk, and calcining the misted clay at 750° C. The misting process increases residue settling rates threefold to 9 cm/min (18 ft/hr) and filtration rates by two orders of magnitude. Leaching-kinetics were determined for misted clay feeds in a batch, stirred-tank reactor. Rapid leaching occurred during the first 85 to 90 pct of the extraction. The linear relationship of extraction to time during this initial phase corresponded to a zero order reaction with a rate constant of around 10 pct/min.

Jan 1, 1981

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978

By Kenneth E. Hjelmstad

The U.S. Bureau of Mines (USBM) has developed an electromagnetic (EM) fire warning alarm sys-tem for underground mines. The system generates a magnetic field for through-the-earth signal trans-mission to microreceivers carried by individual miners. EM fields can induce electric currents in metallic conductors; if an EM transmitting antenna and an electric blasting cap array are too close, the field could induce a current in the blasting array and cause an unintentional initiation of the electric detonators. The USBM conducted tests that define the safe and unsafe regions for using electric detonators near the transmitting antenna of the warning alarm system. The minimum safe distance between a transmitting antenna and a blasting array is the distance where the induced electrical current in the blasting array is 50 mA, which is the safe current level specified in Federal mine safety regulations. Tests indicate that at transmitting power levels of 100-and 1,000-W, separation distances of 9 and 21 m, respectively, were required. These distances are small compared with the dimensions of a mine. Thus, the tests indicate that, with proper placement of the transmitting antenna, the warning system can be used safely in the proximity of blasting arrays.

Jan 1, 2010

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By McHenry Mosier

The application of diamond drills for blast holes is limited to the special Job of extracting floor and stope pillars, and therefore their operation is intermittent. The zinc ore drilled occurs in metamorphosed dolomitic limestone. The mining method is sublevel open-stoping on 200- foot lifts. Ample fresh air is provided by mechanical ventilation. Diamond drilling blast holes began in August 1944. Drills were mount- ed on a 3-inch quarry bar. The contract price for labor for operating equipment owned by the company was $0.23 per foot. The diamond bits were cast-set at the factory in a sintered tungsten matrix. Bit replacement costs were $0.15 to $0.20 per foot drilled. The feet drilled per bit ranged from 87 to 258. The feet drilled per diamond-drill shift ranged from 121 to 129. Holes were loaded with 60-percent special gelatin dyna- mite and fired electrically. In percussion drilling, the estimated feet drilled por machine shift with hand-held sinkers was 65. The tons broken per machine shift averaged 40 throughout the mine. Detachable bits have been adopted recently. The principal advantage of diamond-drilling blast holes at the Balmat mino is the extraction in a safe manner of ore not minable by short-hole drilling. The principal disadvantago is the greater cost per foot of holo in comparison with percussion drilling.

Jun 1, 1947

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By Todd M. Ruff

The lack of visibility near earthmoving equipment resulted in six fatalities in U.S. surface mining operations during 2003. These accidents were the result of either a piece of equipment striking another vehicle or worker, or the equipment traveling over the edge of an embankment. Figure 1 is an example of a recent accident that resulted in serious injuries to one worker and fatal injuries to two others when a van parked in front of a haul truck. Two fatalities occurred in separate incidents when front-end loaders struck workers. Another two workers were killed when their equipment backed over the edge of a highwall or dump point [1]. There is clearly a need to provide better information to equipment operators regarding their surroundings. [ ] Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are working to reduce these accidents by developing systems that sense obstacles and changes in terrain near the equipment and provide this information to the operator. Many off-the-shelf proximity warning systems that were developed for automobiles, light trucks, and recreational vehicles were evaluated on off-highway dump trucks [2]. Many limitations were found with existing systems, including frequent false alarms, limited detection range, a lack of specific information on an obstacle (e.g., location, identity), difficulties in finding suitable mounting locations, and an inability to withstand the environment. These limitations have necessitated the development of new systems designed specifically for large, off-highway, earthmoving equipment. New off-the-shelf systems available for mining equipment include radar and tag-based detection systems. Prototype systems now being developed include a proximity warning system based on the Global Positioning System (GPS) and a computer-assisted stereovision system. Development of these new systems was accomplished by working with manufacturers to modify existing systems to meet the needs of surface mining and through cooperative research with organizations to develop completely new solutions. A typical proximity warning system consists of a sensor or antenna mounted on the equipment that detects the presence of obstacles and an alarm interface in the cab of the equipment. Some systems, as described in more detail below, also require that other vehicles and personnel on the ground be outfitted with electronic tags that transmit an “I’m here” signal back to the system (e.g., radio signal detection systems or GPS). Many types of proximity warning systems are on the market, but they are not all discussed in this paper. APPROACH In past work, engineers at NIOSH evaluated several off-the-shelf proximity warning technologies in order to verify their effectiveness on off-highway dump trucks [2]. Dump trucks were chosen because of the number and severity of accidents involving this type of equipment and because extensive blind areas around these trucks are typical. This experience allowed engineers to limit the number of systems chosen for long-term tests at mine sites to those systems showing

By Richard F. Hewlett

An attempt has been made to fit assay data from an underground copper deposit to a three-dimensional polynomial surface as a means of expressing assay points in terms of their mine coordinates by a mathematical equation. The resulting equation was evaluated to predict the grade trend of the deposit. Although the fit obtained by this initial experiment is not considered accurate enough to provide good predictions about the deposit, the methodology is presented in this preliminary report to show the potential usefulness of the technique in mineral deposit evaluation. The technique also should be useful in determining the grade of blocks of ore for production scheduling and blending problems in open pit operations. Further experimentation is needed to increase the reliability of the computer program, to increase the precision of the method, and to make the solution more flexible for use on other mineral deposits.

Jan 1, 1964

Objective To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs. Background Many types of heavy equipment are used in mining, construction, and agriculture. Most have enclosed cabs to protect the equipment operator from excessive dust and noise exposure. When the equipment is new, controls are normally implemented into the cab to keep these exposures at acceptable levels. However, as this equipment becomes older, many components of the enclosure deteriorate, such as gaskets and seals. This causes the effectiveness of the enclosed cab to be greatly reduced. Once this occurs, the equipment operator's dust exposure can increase to hazardous levels. In surface mining operations, elevated exposures to crystalline silica have caused an excessive incidence of silicosis. Approach A cooperative research study with a mining operation and a cab filtration company was conducted to evaluate the effectiveness of retrofitting an older surface drill with two controls to lower the drill operator's respirable dust exposure. These two controls were: (1) A good air filtering and pressurization system to ensure that clean air was delivered into the enclosed cab. Ideally, the incoming air filter should be 99% efficient in removing particles with an aero- dynamic diameter of 0.3 pm or greater from the airflow. (2) Sufficiently sealing the cab to develop a positive static pres- sure and ensure that dust was not leaking into the cab. This was done by plugging all holes and cracks and maintaining good gaskets and seals. To prevent wind from forcing contaminated air through holes in the cab, the cab's static pressure must be greater than the wind's velocity pressure. During the course of this research, it was found that a floor heater fan used in the drill during the winter months greatly increased the operator’s Respirable dust exposure. Problem Identification Four days of background dust levels were measured as a baseline for this research. These baseline measurements were taken in May 2000 when air temperatures ranged from 60° to 70° F. When this was completed, the two controls were implemented. The first control was to install an improved air filtering and pressurization system on the enclosed cab. This was composed of a two-stage prefilter, a blower, then the respirator-medium secondary filter. Since the secondary filter was on the positive side of the fan, all air delivered into the enclosed cab had to pass through this secondary filter. After the filtering system was installed, the cab was pressurized to a static pressure of0.01 inches of water (w.g.), which is still very minimal. The second control was to seal the cab. New door gaskets were installed, and all cracks and holes in the shell of the enclosure were plugged. This increased the cab pressurization to approximately 0.1 inches w.g.

Mar 1, 2001