Search Documents

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By R. V. Ramani, R. L. Grayson, R. L. Frantz, V. A. Marple, W. R. Myers, K. L. Rubow, Mutmansky. J. M., T. J. Stobbe

"An investigation of protocols for research performed from 1953 to 1988 on pneumoconioses (with emphasis on diseases related to coal and silica) was conducted in the Generic Mineral Technology Center for Respirable Dust. In addition, interviews were conducted with prominent U.S. medical researchers, aerosol scientists and engineers in government, industry, and universities to determine dust sources, dust preparation methods, laboratory protocols, and determinant variables related to in vitro and in vivo research and assess the comparability of results.Since the original report on the protocol project, additional research regarding free radical existence in freshly produced dust particles and the shape and contamination of particles generated for research purposes has further heightened scientists' concerns. As indicated by current research, fresher dust particles and those with more angular shapes may have a different level of reactivity in biological systems than do older or more rounded particles. Therefore, research on dust preparation methods for biomedical studies was undertaken and will be outlined here.Results of protocol review and interviews are summarized. Research on size reduction methods and their particle characteristics plus some recommendations concerning dust preparation methods and reporting in biomedical publications are also presented. Recent evidence indicates that these recommendations may be of importance in comparing and interpreting research results."

Nov 1, 1995

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By John H. Soulé

"INTRODUCTION Spodumene and lepidolite were shipped from the Harding pegmatite deposit, Taos County, N. Mex., in the period from 1930 to 1930. Tantalum minerals were noted as early as 1924 and described in 1931 3/ but no tantalum ore was shipped until 1942. The deposit was mapped and studied by geologists of the Federal Geological Survey and engineers of the Bureau of Mines late in 1942 and early in 1943, and a Bureau of Minus exploratory project was carried out in 1943. 4/ Thu following report presents the results of that project.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Minos has as its primary objective the more effective utilization of our mineral resources to the end that they make the greates possible contribution to national security and economy. It i the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lovell B. Moor, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallugiical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By H. M. Smith

In studying the chemistry of lubricating-oil fractions from so-called ?paraffin-base? crudes, one of the first requisites is a method for the separation and removal of waxy material. A method utilizing solvents for this purpose is described in this report, together with preliminary experiments with solvents that led to its development. The solvents actually used are secondary butyl alcohol, acetone, and mixtures of these.. Isopropyl alcohol was also studied. Preliminary Experiments In previous work on "intermediate-base" crude oil, following the work of Wyant and Marsh acetone had been used for laboratory separations of oil and wax. Then acetone was tried for the separation of the waxes and oils of "paraffin-base" crude, the volume of acetone required (80 parts to 1 part of oil) was found to be too great for large-scale work. For this reason the effectiveness of other solvents was studied; the separation by acetone, however, was used as a standard.

Jan 1, 1927

In 2005, a total of 4,490 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.6% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,039; 45.4%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Of all states, Pennsylvania had the most stone mines (n=379; 8.4%).

Jan 1, 2008

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By E. L. Sweeney

The mine and mill of the Davis-Dunkirk Lines, Inc., are about 16 miles by road south of Prescott, Ariz., which is the nearest railroad point for receiving mine and mill supplies and for shipping concentrates to smelters. A good trucking road reaches within 2 miles off the property, but from that point the grade is very steep. Outgoing loads are limited to 2 tons. The topography near the mine is exceedingly rugged, and the area is slightly wooded. The climate is mild excepting in a few winter months, when the snowfall is heavy. Electric power is secured by way of a 4 1/2-mile, high-tension line connecting with the main line of the Arizona Power Co. The concentrator was intended to treat 60 tons or more daily of gold-silver-copper ore and make a single gold-silver-copper concentrate for shipment to a copper smelter.

Jan 1, 1933

By Carl Belser

In 1925 the Park Utah Consolidated Mines Co., after several years of experimental work, installed a system for signalling from cages which has been operating efficiently and with low upkeep costs for the post 19 years. The system was adopted for a large western metal mine but was later abandoned be arse of the constantly shifting shaft alinement. Recently the system has been studied and probably will be put into service at two other large mines. One of the principal reasons wry the system has not boon adopted more widely has been the lack of adequate details both as to the desirability of having such a system and as to its construction and operation. Previous signaling, systems contained undesirable features, such as charged bare wires extending the full length of the shaft. Under the direction of O. N. Friendly, then general superintendent of the Judge Mining & Smelting Co., the present system, entailing the use of a samll current at low voltage, was gradually developed. Many of the refinements in the system wore contributed by Leonard Wilson, consulting electrical engineer, Salt Lake City, Utah.

Jan 1, 1945

By Harry W. Campbell

In 1986 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 2 acre North Sisters Rocks Wilderness Study Area (OR-12-8) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Curry County, Oregon, about 15 miles north from Gold Beach. No mines, prospects, or mining claims were located inside the study area, and no mineral resources were identified. Stone from the study area could be quarried and used for construction purposes; however, two nearby quarries have sufficient stone to satisfy local construction needs. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and mineral resource potential of the North Sisters Rocks WSA (Wilderness Study Area) 1/ at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of investigations will be used to help determine the suitability of the North Sisters Rocks WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1987

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By John R. Shattuck

As a part of the general chromite investigation in California designed to aid In the production of chromite during the recent war emergency, the Bureau of Mines explored the Coggins property in Siskiyou County, Work by the Bureau in cooperation with the Federal Geological Survey began in October 1942 and was concluded in March 1943. This report presents a brief history of the mine, outlines the physical features of the district, describes the deposits) and explains the work completed by the Bureau of Mines, Table 1 shows the analysis of diamond drill-hole samples. The logs of drill holes are in the appendix.

Jan 1, 1949

By John I. Kasteler

The Rambler mine is in the Douglas mining district, Albany County, Wyo. (fig. 1). The property was first operated about 1870 for gold found in the outcrop of a leached ore body. Copper and metals of the platinum group were discovered, in 1900, or soon thereafter, and intermittent mining was done until 1918, when a fire destroyed the surface plant, and the underground workings caved. The mine has since been idle. The Bureau of Mines conducted a development project on the property from October 1942 to October 1943, with a recess period between November 1942 and August 1943. Ten diamond drill holes, totaling 1,859 linear feet, were drilled on the property (fig. 2). The mine dump was sampled after preparation with a bulldozer. Assay determination and spectrographic analyses disclosed small quantities of copper and metals of the platinum group in the samples. Determinations were made on 11 samples from the diamond drill holes and 23 samples from the mine dump. The assay results and spectrographic analyses are given in tables 1 and 2. The logs of the diamond drill holes are given in an appendix to this report.

Jan 1, 1949

By T. L. Joseph

The purpose of this article is to describe briefly the operation of a 6-ton blast furnace on a charge of bauxite, limestone, iron ore, and cast-iron turnings and to point out the bearing which smelting such a charge has upon the production of alumina cement. One object of the experiment, conducted by the Bureau of Mines in cooperation with the Aluminum Co. of America, was to determine whether tae so-called Pedersen process3 can be applied to the blast furnace. This process consists of smelting a charge of bauxite, iron ore, and. limestone, and results in to products. One is a slag containing about 50 per cent of A1203 and is intended for use in manufacturing aluminum, and the other is iron low in sulphur. Complete details of the test are published in other reports4. Blast-furnace slag is now recognized as a satisfactory and economical raw material for making Portland cement, Wm. A. Forbes5 has recently reported that in 1926 an important steel interest used well over 1 million tons of slag in producing about 24 million long, tons of cement. This is equivalent to about ½ ton of slag for each ton of cement. Alumina cement can be made direct in the blast furnace. Its physical character would have to be changed by grinding, but no change in its chemical composition would be necessary.

Jan 1, 1928

By D. Harrington

"In order to stimulate general interest in mine safety among their employees the mining companies of Butte, Mont., instituted in 1918 a Miners' Field Day, and this field day has since been held annually about the end of July, the last one being on July 25, 1921. The mining companies of the Butte district finance this meet in proportion to the number of men employed at the time of the meet, the contributing companies with number of working force, end proportional contributions for the opening field day in 1918 being given below:COMPANY NUMBER EMPLOYED AMOUNT CONTRIBUTEDAnaconda Copper Mining Co.,12,500,$ 1,078.53Butte & Superior Mining Co.,1,800,155.32North Butte Mining Co.,,1,294,111.67East Butte Copper Co.,,850,73.36W. A. Clark Interests,,600,51.78Davis-Daly Mining Co.,,340,29.35,,,,17,384,$ 1,500.00*Note: In many mining districts it is now the custom to hold an annual Miners' Field Day. The field day, as a rule, is financed principally by the mine operators, and was instituted primarily to promote interest among miners in the ""Safety First"" movement. Usually demonstrations or contests in first aid and mine rescue are the leading feature of the day's events, which include games, races, dancing, and all the other amusements usual to a gala holiday. Thus the field (ley serves the double purpose of stimulating interest in mine safety and promoting cordial relations and community fellowship. This paper is an interesting account of the way in which the Miners' Field Day in the Butte district is organized, with data on costs, plan of organization, method of conducting, and the practical benefits derived from it. - Ed"

Oct 1, 1921

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981