Search Documents

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By John Durkin

The Bureau of Mines has conducted field studies in coal mines through- out the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coalfields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10-pct false alarm rate, the expected probability of detecting a miner's signal from a depth of 1,000 ft is 54 pct; at 500 ft it is 95 pct. These depths exceed the actual depths of 90 pct and 50 pct, respectively, of U.S. coal mines. Sensitivity studies have shown that at a depth of 1,000 ft, for every 3 db of improvement in signal-to-noise ratio, the probability of detection increases 6 to 8 pct.

Jan 1, 1982

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to can and ore rate mines in various foreign countries. This interpretation of the mining laws of the Irish Free State has been prepared from the best available material in Washington and is released subject to amplification and correction, if necessary, by American foreign-service officials. INTRODUCTION This paper is based upon the mines and minerals act, 1931, enacted by the Legislature (Oireachtas) of the Irish Free State (Saorstát Eireann), December 22, 1931, the lull title of which is "An act to establish a board to perform functions in relation to mines and minerals, to authorize the making of lenses of mines and minerals belonging to or vested in Saorstát Eireann, to name provider for facilitating the working of other mines and minerals and, for imposing restrictions on the working of minerals required for the support of buildings and works, to amend the law with respect to mines, and for other purposes incidental to the matters aforesaid.'

Jan 1, 1933

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By A. Adams

The quality of hafnium metal produced by the Kroll process depends upon the purity of the hafnium tetrachloride. This investigation of methods for purification of hafnium tetrachloride was undertaken to aid in producing a higher purity hafnium metal than is currently produced by the Kroll process, The quantities of metallic impurities in hafnium metal were decreased by contact with molten alkali-metal chloride salt. Contact was achieved by a semicontinuous process of bubbling gaseous hafnium tetrachloride through a molten salt bath or by a batch process, first fusing the tetrachloride with a combination of alkali chlorides and then heating the mixture to sublime the hafnium tetrachloride. Low-melting mixtures of sodium, potassium, and lithium chlorides were used to purify hafnium tetrachloride. About 30 percent of the initial hafnium tetrachloride was trapped during purification with alkali- metal chloride salts. The 95-percent confidence limits (6)4 for the amount of oxygen decrease 60 and 34.3 parts per million when the batch purification is combined with a reduction so that both take place in the same equipment,

Jan 1, 1961

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By Bernadette Michalski

Although hydrocarbons accounted for more than 60% of Bahrain's income and more than 80% of export earnings, this island nation sustained one of the more diversified economies in the Gulf Region. The availability of low-cost natural gas for electric power has fostered the development of a significant aluminum refining and manufacturing industry with emphasis on vertical integration. The Bahraini iron pelletization plant, closed since 1986 due to financial problems, was scheduled to reopen by early 1989. Commodity Review Metals.-Aluminum.-Aluminium Bah-rain Bsc (Alba) attained record high production levels in 1988 taking advantage of favorable aluminum prices, which averaged over $2,000 per ton as compared with less than $1,500 per ton in 1987. Net aluminum production was nearly 13,000 tons over design capacity. Fewer standard ingots (52,081 tons as compared with 79,685 in 1987) were produced as Alba concentrated on higher value added products such as rolling ingots (42,324 tons as compared with 32,125 tons) and extrusion billets (60,934 tons as compared with 46,618 tons).

Jan 1, 1990

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984

By R. S. Conti

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide (CO) sensors, and a point type heat sensor (PTIIS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s, The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS, A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and C8 sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity, Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners' escape.

Jan 1, 2010

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Anatol Wojtowicz

This research program was conducted to determine if respirable coal dust emanating from a continuous mining machine can be suppressed more effectively by a high expansion foam than by the water sprays conventionally used. A high expansion foam system was developed and tested on a continuous mining machine under actual operating conditions. The utility of the system was demonstrated. Test results tend to show that foam application is more effective than water sprays in suppressing respirable coal dust. However, because of the extreme variability of the test conditions, scatter in the sampling data, and other factors, not enough data was obtained to form a firm conclusion that foam is more efficient than a water spray in suppressing respirable coal dust. Sufficient statistical data was obtained, however, to indicate that foam is more efficient than water in suppressing total float coal dust.

Jan 1, 1974

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By Ralph H. Espach

The value of careful fractionation in the manufacture of petroleum products is recognized more and more by petroleum refiners. Recent studies have shown that the quality of the products depends largely on the type of fractionating equipment and on the care used in operating the equipment. For example Rue3 has shown that careful fractionation of pressure distillate will greatly reduce the amount of chemical treatment necessary to produce finished gasoline. The advantages of the combination of pipe still and bubble tower in obtaining good fractionation are well recognized in the petroleum industry. However, the equipment designed in the past has in general been much too large for convenient laboratory use. The present paper describes a continuous-distillation apparatus for the laboratory study of fractionation. This apparatus has given very satisfactory results in the study of different crude oils and petroleum products. A discussion of the theory and action of bubble towers has not been given, as this subject has been discussed previously by Cooke and Rue4. It is believed that the distillation curves of the products obtained from this apparatus show clearly its capabilities.

Jan 1, 1928

By Lloyd A. Morley

A guide to the development and use of an APL computer program for the analysis of load-flow problems is presented. The program is designed to provide an interactive method of load-flow study to improve underground coal mine electrical system design and safety. The theoretical basis for load-flow analysis is discussed, along with per-unit calculations which facilitate computation. Specific input/output, execution and network modification procedures are presented for using the APL program. In addition, typical results are given for examples taken from power system analysis literature.

Jan 1, 1977

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a new methane analyzer system for underground applications. Methane enters coal mine ventilation air from the breakup of coal at the active face, from the collapse of roof rock during retreat mining, and from the ribs abutting virgin coal. Each source contributes varying amounts to the total emission, depending upon rate of mining, type of mining, and the character of the coalbed and adjacent strata. The evaluation of individual parameters of methane emission requires the continuous monitoring of individual mine sections over a long period of time. The methane analyzer system was developed to meet this need. The system has been installed and operated in an active mine in the Pittsburgh coalbed. The system and details of its installation and calibration are described. Data are presented to substantiate its reliability.

Jan 1, 1975