Search Documents

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By E. A. Loria

The Bureau of Mines analyzed the effects of oxygen, nitrogen, and carbon on the tensile properties of electrorefined vanadium in terms of the Petch equation. The effects of the different impurities and grain sizes on the yield and flow stress between 2730 and 770 K were studied. For specimens of like composition, the values of the Petch parameters 01 and ky obtained by two different methods, extrapolation and grain size, were nearly the same. For high-purity electrorefined vanadium, the 01 value at 2730 K was 10,300 psi (5,150 psi shear). The 01 values for this metal at 1950 and 2730 K were lower by factors of 3 to 4 than for three less pure samples of commercial vanadium metal of equivalent grain size. Nitrogen was more effective than oxygen in increasing 01' the increase being about twice as much for the same impurity level. Carbon produced a slight increase in 01 up to 0.024 percent and then a gradual decrease in 01 to 0.11 percent, the maximum carbon content studied. The corresponding ky values followed the same trend in regard to oxygen and nitrogen additions, whereas the addition of carbon produced no variations at either temperature. Dislocations in vanadium are anchored by carbon, oxygen, and nitrogen with increasing firmness in that order. The high purity of electrorefined vanadium was confirmed by low yield stress and high ductility throughout the low temperature range. The metal also exhibited profuse twinning with high ductility at 1230 and 770 K. The effective surface energy for fracture, y, was found to lie between 3.3 and 3.6 x 1()4 erg cm-2?

Jan 1, 1966

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By C. M. McKinney

This report contains Bureau of Mines routine crude-oil analyses of 20 samples from5 areas on the arctic slope of Alaska. Two samples were condensates from the South Barrow gasfield, Barrow Lakes area. The remaining 18 samples were crude oils from the following areas: Barrow Lakes, 1 seepage sample; Umiat, 10 well samples; Cape Simpson, 1 seepage sample and 3 well samples; Fish Creek, 2 well samples; and Wolf Creek, I well sample. Table 1 summarizes information on the origin of the crude-oil samples, and table 2 summarizes characteristics of the samples. Item numbers in both tables correspond to item numbers of the analyses at the end of this report, and the samples are referred to by these numbers throughout the text.

Jan 1, 1959

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By X. C. Shi

Bacterial mutagenicity and mammalian cell chromosomal and DNA damage in vitro assays were performed on a diesel exhaust particulate material (DPM) standard in two preparations: as an organic solvent extract, and as an aqueous dispersion in a simulated pulmonary surfactant. U.S. National Institute for Standards and Technology DPM SRM 2975 expressed mutagenic activity in the Salmonella reversion assay, and for in vitro genotoxicity to mammalian cells as micronucleus induction and as DNA damage in both preparations: as an acetone extract of the DPM mixed into dimethylsulfoxide, and as a mixture of whole DPM in a dispersion of dipalmitoyl phosphatidyl choline. Dispersion in surfactant was used to model the conditioning of DPM depositing on the deep respiratory airways of the lung. DPM solid residue after acetone extraction was inactive when assayed as a surfactant dispersion in the micronucleus induction assay, as was surfactant dispersion of a respirable particulate carbon black. In general, a given mass of the DPM in surfactant dispersion expressed greater activity than the solvent extract of an equal mass of DPM.

Jan 1, 2009

By T. J. Williams

Researchers at the U.S. Bureau of Mines monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s LUCKY Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 2010

By Thomas J. Peters

The Danskin/South Fork Boise River study area is 40 air km southeast of Boise, Idaho. The 16,000-hectare, two-segment area is mainly underlain by Cretaceous-age granodiorite and an aplitic and pegmatitic complex of the Idaho batholith, Miocene-age rhyolitic tuffs and lavas, and late Tertiary-age basalt flows. No mineral resources were identified in the study area. One mine, The Flat Creek mine, which produced several ounces of gold and silver, was found in the study area. It is geologically similar to deposits in the Neal mining district, adjacent to the northwest corner of the area; gold mineralization occurs along east-northeast-trending faults and associated quartz veins, which dip moderately to steeply southeast, and within adjacent Cretaceous granitic rock. Samples indicate the Flat Creek deposit is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. However, exploration is warranted there and also in the 7-km interval to mines in the Neal district, and for extensions of those mines. No evidence of geothermal activity was observed, although there are hot springs in the vicinity. Some alluvial (placer) samples from the interior of the study area contained free gold, but no substantial gravel deposits were seen.

Jan 1, 1993

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By A. B. Needham

This report describes the exploration work done in 1941 in connection with the search for strategic minerals as authorized by the Strategic Materials Act approved by the President on June 7, 1939. It deals with the various manganese deposits and showings in the Tombstone mining district of Cochise County, Ariz. The exploration project comprised a study of the geology, mapping of the areas, and exploration of various mines and deposits by sampling old drifts, crosscuts, and scopes, supplemented by diamond drilling from underground stations. The Federal Government's manganese-purchasing programs have revived interest in occurrences such as the scattered deposits near Tombstone. Because of this, the Bureau of Mines project report on the Tombstone district, prepared originally in 1941 but not published, has been revised and now is being made public.

Jan 1, 1956

By R. V. Ramani, R. Srikanth, R. Zhao

"A two-pan study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbon/volatile matter), Vitrinite Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.Mineral particles in the range of one to five microns, if inhaled in sufficient amounts, lead to a number of lung diseases generally referred to as pneumoconiosis. A priori knowledge of the mechanisms and rates of fine particle generation during mining can aid in the development of more effective technology for controlling primary dust generation. Unfortunately, the data and knowledge currently available are not adequate for this purpose. In fact, a committee of the National Academy of Sciences on the measurement and control of dust concluded that the knowledge of the fundamental mechanisms by which coal mine dust is generated and a part of it is entrained in the mine atmosphere as respirable dust is not sufficient to clarify, let alone control, the processes involved (Anon., 1980). Under a research contract from the U.S. Bureau of Mines, Stecklein et al. (1982) have identified a number of fundamental research issues for understanding the coal fragmentation and entrainment processes.Reduction of dust generation is the best means of control since fine particles are difficult to control once they become airborne. Therefore, considerable research efforts have been directed to understand the factors influencing dust generation and entrainment, including machine design, water sprays, and ventilation. Laboratory studies have been conducted on the mechanical action of bits and machine power requirements (Evans and Pomeroy, 1966; Roepke, 1984). Since the physical characteristics of coal play an important role in the process of breakage, a number of laboratory studies have been conducted to study the relationship between coal characteristics and respirable dust generation (Baafi, 1977; Moore, 1986; Polat, 1990; Thakur, 1971). Several studies have been conducted on the relationships between coal characteristics and airborne dust concentrations (Hamilton and Knight, 1958; Khair and Xu, 1991; Organiscak and Page, 1993; Page et al., 1993). A limited number of studies have also been conducted on the relationships between coal characteristics and airborne dust concentrations in mines (Organiscak et al., 1990). Yet, no reliable method has been developed to rank coal seams according to their respirable dust generation potential. The conclusions derived from previous studies can be summarized as follows:"

Dec 1, 1996