Search Documents

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By Robert W. Freedman

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

By J. M. Gomes

The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral concentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low-and high-intensity magnetic, high-tension, and flotation equipment.

Jan 1, 1979

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Hillary W. St. Clair

This report describes a mathematical procedure for analyzing size distribution data by the method of moments. The method was applied to Andreasen's data on a variety of grinding mill products. It was found that the observed size distributions could be represented by gamma and beta distribution functions over a wide range of sizes. A computer program, written in BASIC, is described for calculating moments, distribution parameters, and the weight fraction in any size range.

Jan 1, 1969

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By Milton Orchin

There has been a good deal of speculation as to the function of a vehicle in the coal hydrogenation process. One of the most fruitful theories has been the suggestion that a vehicle such as tetralin functions by supplying hydrogen to the coal, and that the high-pressure hydrogen present in the system serves to regenerate the tetralin. In order to obtain experimental evidence bearing on this theory, a series of experiments was planned in which varying quantities of tetralin were used with coal in the presence of high-pressure hydrogen. This paper reports the results of these experiments.

Jan 1, 1949

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965