Search Documents

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By R. V. Higgins

This report presents the results of a study of gas injection in the Upper and Lower Terminal zones in fault block VB and in the Upper Terminal zone in fault block VI, Wilmington field, California. This report is based on data obtained to January 1956. Earlier studies of gas injection in other California fields have been reported .3/ The Upper and Lower Terminal zones, fault block VB, have been producing oil since 1945 and the Upper Terminal zone, fault block VI, since 1948. Before starting the gas-injection project, the expansion of dissolved gas was the principal mechanism moving the oil to the wells. Gravity drainage and an edgewater drive also have contributed to the movement of the oil to the wells. When the gas injection was begun, the reservoir pressure and the oil production had declined appreciably. Gas injection was started in the Upper and Lower Terminal zones, fault block VB, in May 1953 and in the Upper Terminal zone, fault block VI, in October 1953.

Jan 1, 1957

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By D. S. Kingery

Efficient transportation is necessary to complement modern mechanized mining methods. The increasing trend toward high-capacity face loading equipment has demanded equally efficient haulage methods; this has been met by increasing mine-car sizes, using larger locomotives, and increasing haulage speeds, all requiring properly installed and maintained haulage roads specifically designed for this type of traffic. The recommendations and specifications included in this circular were made to point out salient factors important to the proper construction and maintenance of track haulage roads and to serve as recommended standards for track installation and maintenance. GLOSSARY OF TERMS USED Haulageway. - The track, walkway, trolley wire, feeder lines signal end telephone lines, signals, telephones, support, and drainage of the entry referred to. Subgrede. - The base upon which the ballast is laid.

Jan 1, 1954

Real economic growth for 1988 may fall short of the 3.3% projected by the U.S. Department of Commerce in August 1988 be-cause the summer drought and intense heat in many areas curtailed output more severely than expected. The economy grew at an average annual rate of 3.0% for the first three quarters of the year, slowing in the second and third quarters. Export growth, which occurred even as the dollar edged up com-pared with other industrial country currencies, was an important factor in the expansion. Notable gains were posted in sales of machinery, computers, aircraft, chemicals, and telecommunications equipment. Imports increased, but not as much as exports, and the U.S. trade position was still much improved from that of 1987. Personal consumption expenditures grew slightly faster than the economy as a whole. Purchases of consumer durables showed notable strength in the first half of 1988, but slowed down in the third quarter. [ ] Despite the moderate rise in interest rates, business spending for new plant and equipment also rose and contributed to 1988 gross national product (GNP) growth. Both new business investment and export demand spurred orders for U.S.-made machine tools. Orders for machine tools for the first 8 months of 1988 were almost triple those for the corresponding period in 1987.

Jan 1, 1988

By Joseph Grumer

Reported fiscal year 1973 studies of fires and explosions seek to develop capabilities during mining operations to detect and quench ignitions of gas in the face area, to detect and quench by means of passive or triggered barriers explosions propagating in rock-dusted coal dust, and to detect incipient fires early enough for easy extinguishment. Research discussed includes minimum air velocities to lift coal or rock dusts, surveys to determine adequacy of rock dusting, chemical agents to quench gas or coal dust explosions and their relative efficacies, spectra radiated by explosions, and nozzle sprays of extinguishants.

Jan 1, 1973

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By H. E. Peterson, W. L. Anderson

"INTRODUCTION The great demand for tungsten incident to the war has led to the exploration of a large number of low-grade tungsten deposits. To properly evaluate the low-grade deposits it is essential to have available a dependable method of analysis applicable to all types of low-grade tungsten ores. Results reported on the tungsten content of the ores have often varied quite widely and have led to confusion. The Bureau of Mines has been requested by Government lending agencies and by companies interested in the production of tungsten to publish a general method for the determination of tungsten in low-grade ores. To meet this need, the Bureau of Mines is herein submitting two methods for analysis that have been proved on a large number of tungsten-bearing ores various types in the Bureau of Mines laboratory in Salt Lake City. Also, a third method was developed that requires no cinchonine and has proved to be applicable on most tungsten ores. The cinchonine method is the generally accepted for analysis of tungsten ores. Very reliable results can be obtained by this method if certain precautions are taken, as outlined in this report."

May 1, 1943

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support given through cooperative agreements by the following organizations to investigations con¬ducted by the Explosives Research Center during fiscal year 1965: Dow Chemical Company Manufacturing Chemists' Association Monsanto Chemical Company The Sulphur Institute

Jan 1, 1966

By Oliver Bowles

"Score of the Bureau's Investigations.There has been outlined in a previous report* the results obtained regarding the adaptability of pulverized waste slate as a filler in road asphalt mixtures. As pointed out in that report the percentage of waste at slate quarries is very high, and the Bureau of Mines has undertaken the problem of discovering new and enlarged outlets for the waste material.Many products such as paper, rubber, road asphalt, floor coverings, paints, etc., require as one of their important constituents a considerable percentage of finely pulverized inert mineral matter to give ""body"", to obtain the desired consistency, or to supply the necessary wearing or other qualities demanded. Such materials are known as ""fillers"". The possibility that slate flour might be used as a filler with advantage in several products other than road asphalt led the Bureau to undertake further investigation.The Importance of Discovering Advantageous UsesIt has been found that in some products slate may be substituted for materials now in use without any marked effect on the quality of the products. A wider use of slate in such products could result only from a definite price advantage as compared with other fillers. Mile it is probable that waste slate may be placed on the market at prices which will encourage its wider use, it is evident that a waste slate utilization industry can never attain sufficient magnitude to definitely assist the slate producers unless it is demonstrated that some definite advantage in quality may be gained when slate is substituted for fillers now in use. The main purpose kept in view throughout the inquiry has been, therefore, to find advantageous uses for waste slate in order that both producer and consumer may be benefited."

Sep 1, 1921

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By Lloyd A. Morley

This annual report details progress under USBM Grant G0155003 during the project period of January 1, 1977 through December 31, 1977. The report contains four principal chapters covering accomplishments in the mine electrical safety research areas of continuous monitoring, battery and battery-charging safety, and computer modeling. Highlights of the work are summarized in the last report chapter.

Jan 1, 1978

By W. G. Sandell, G. M. Potter

"As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agencies engaged in purchasing and stock-piling some of the more critical and strategic materirals. At the request of George A. Easley, representative of the MetalsReserve Company, beneficiation studies were made on a sample of complex tin-tungsten ore from the Urania mine in Bolivia, South America.The low-grade Urania ore (1.9 percent Sn and 1.55 percent W03) contained a very complex of cassiterite and scheelite with iron sulfidesand quartz. The problem involved in concentrating this ore was the removal of sulfides and silica by stage flotation and gravity concentration for the production of a marketable tin-tungsten concentrate. The sulfides and primary quartzite were readily rejected, but the secondary quartz was intimately associated with cassiterite, and ultimate recovery depended on treatment of minus 560-mesh (theoretical) sizes.The ore was amenable to concentration by ore dressing. Seventy percent of the tin and 83 percent of the tungsten were recovered in a product that assayed approximately 20 percent Sn and 20 percent W03 and that met grade ""F"" specifications of the Metals Reserve Company for mixed tin-tungston concentrates."

Feb 1, 1948

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

By Charles L. Harnes

A mineral pigment is a colored substance dug from the ground, which after treatment can be mixed with a drying oil to form a paint. Not all colored earths, however, can be made into satisfactory pigment. Much depends upon the attractiveness and uniformity of the color and the ease of purification. Mineral pigments are distinguished from chemical pigments by a difference in origin and treatment. Chemical pigments are not found ready-made in the earth but must be synthesized or otherwise obtained from other compounds or elements; for example, cadmium yellow, a chemical pigment, is precipitated from a solution of cadmium chloride, hydrochloric acid, and sodium sulfide.

Jan 1, 1942

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By (NIOSH) Publication

In 2004, a total of 2,011 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.9% of all mining operations.

Sep 1, 2007

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960