Search Documents

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

The request for proposal from the U.S. Bureau of Mines outlined the purpose of this study in the following terms. "High grade near surface deposits are largely a matter of history. Most of the current mineral production in the united States is from large low grade ore deposits mined by large scale methods. It appears likely that exhaustion of near surface deposits and public resistance to open pit mining will tend to reverse the present trend toward open pit mining and lead to increased reliance on large scale underground mining. In view of the long lead time needed to improve basic technology, an in-depth study of the major underground mining methods is needed. "This study is intended to provide a systematic review and analysis of large scale non-coal underground mining technology with particular emphasis on current practices and problems, needed technological improvements, existing or potential environmental conflicts, and possible modifications or innovations that will assist in the satisfaction of projected national mineral supply requirements."

Jan 1, 1974

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By Russell R. Trengove

The largest potential reserves of manganese in Nevada are in the Pioche district. To date, these large reserves of 10-to l2-percent manganese cannot be upgraded economically. Other large, low-grade deposits, such as the Virgin River and Boulder City deposits in Clark County, cannot be considered immediate sources of manganese. Reserves of the principal manganese deposits in Nevada, based on the most reliable estimates, total about 17 million tons analyzing 7.6 to 13.6 percent manganese. Most of the deposits are of a type that cannot be prospected systematically but have been prospected and developed in the course of productive mining operations. To realize production from low-grade deposits that are amenable to concentration, a ready market must be provided. Thus far, Government stockpiles have been the major outlet for these low-grade ores. Research and experimentation over a period of years have led to development of several processes technologically applicable to these low-grade ore bodies, but their economics is not sufficient to allow competition with imported ores on the open market.

Jan 1, 1959

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By K. K. Kelly

METALLURGICAL thermochemistry of titanium is a broad subject and (if data were available) could include a wide variety of topics. The present report is restricted to extractive metallurgy and to substances and reactions that bear upon the magnesium, sodium, and hydrogen-reduction processes employing titanium tetrachloride. The aim has been to present enough data so that the reader not only can check: the calculations for the reactions discussed but also can conduct related calculations if he so desires, without recourse to other compilations of data. The subject matter divides naturally into two parts-the selection of the data to be adopted and the application of these data to pertinent metallurgical reactions.

Jan 1, 1959

By Walter J. Frank

The purpose of the work covered by this contract is to develop a means of designing splice connectors which will significantly improve mine trailing cable splice performance. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. Because of the empirical nature of this effort, time has been devoted to explaining the derivations of the test procedures used. Special attention is given to the splice flexing machine which served as the backbone of the test program. In order to familiarize persons with connector terminology, a section is devoted to a glossary of pertinent terms. Various types of cable joints are also defined. The major effort is a connector design parameter study. Utilizing the optimum parameters developed along with the suggested design procedure outlined in Appendix I should result in significantly improved splice performance and thus meet the objectives of this contract. A field test program was instituted for the purpose of insuring adaptability of connector design and associated installation tooling along with a field performance study. During the course of work, other significant factors affecting splice performance were uncovered. Although not covered by the scope of this contract, a brief discussion is presented for the purpose of stimulating interest in what is considered other fruitful areas for improved splice performance.

Jan 1, 1976

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the pact 32 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued to emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced. American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By George A. Morgan

Output of mineral products was estimated to be unchanged in 1983 from that of 1982 with the exception of petroleum. The country began production of crude oil from the Seme Oilfield, and all output was exported. Wd and charcoal constituted 72% of Benin's total energy consumption, and imported petroleum products and electric power accounted for the remainder. Cement was produced from imported clinker. The gross domestic product (GDP) was $1,061 million in 1982, the latest year for which information was available.2 COMMODITY REVIEW Gold.-Exploration was underway at Perma by the U.S.S.R. as part of the United Nations development program. Gold had been produced previously at Perma, where a grade of 0.289 troy ounce of gold per ton was reported, An exploitation program for the deposit was to employ about 100 people, and output was targeted to reach 1,600 troy ounces per year. Recoverable reserves were put at 96,000 troy ounces.

Jan 1, 1985

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958