Search Documents

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By Wm .. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville , Mont . , is one of a series of similar papers being prepared by the Bureau of Mines on mining practices , methods , and costs in the various mines of the United States .

Mar 1, 1931

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By P. A. Wasson

The investigation described in this publication was conducted by the Bureau of Mines to determine the effectiveness of the anionic silica flotation method on goethitic iron-bearing materials from the Cuyuna Range, Minn. Samples used in this investigation were a composite of drill core from 13 holes, and 3 samples from lean ore stockpiles. These samples are believed to be typical of the mineralization occurring in an area with a potential reserve of several million tans of submarginal iron ore. Results from batch tests showed that the iron-bearing minerals could be effectively concentrated by flotation removal of the siliceous gangue. The drill hole composite yielded laboratory flotation concentrates from locked tests containing 56.8 percent Fe and 6.1 percent silica, with an accompanying iron unit recovery of 94.2 percent. Concentrates containing 52.4 to 53.7 percent Fe also were produced from the lean ore stockpile materials; corresponging iron recoveries ranged from 71 to 79 percent in the batch tests, with the possibility remaining for additional recovery of iron from the middlings.

Jan 1, 1963

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States during the years 1958 through 1960. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included. Silicosis statistics reported by the U.S. Public Health Service indicate a sizable silicotic population in the United States and suggest a need for greater dust-control effort. A joint medical-environmental survey was begun by the U.S. Public Health Service and the Bureau of Mines to evaluate the magnitude of the silicosis problem in the metal mining industry in the United States.

Jan 1, 1962

By D. E. Wolfson

This report presents 900° C BM-AGA carbonization and related data for coals from the principal beds of Nicholas, Randolph, and Webster Counties, W. Va. Thirty-three samples from nine coal beds in three counties were car-bonized at 900° C in the l8-inch-diameter BM-AGA retort, data from which have been correlated with industrial production. Host of the samples were chemically suitable for metallurgical use, and their coking properties were satisfactory. Except for four of the Lower Kit-tanning samples, the ranges of constituents in the coal seams were 1.8 to 9.0 percent ash and 0.4 to 1.1 percent sulfur, values within the range of accept-ability for metallurgical coals. Coke strength indexes were normal for Appalachian coals of similar rank, and the tumbler stability indexes of the coke ranged from 35 to 57.

Jan 1, 1969

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By T. A. Henrie, E. K. Kleespies

Carbon reduction of rutile and ilmenite in nitrogen and ammonia atmospheres was studied as a method of preparing titanium nitride . Ammonia was a better nitriding agent than nitrogen . The contact between the solid reactants , carbon and rutile , was a prime factor in nitrogen atmospheres and was of lesser import in dissociated ammonia . The reduction process for conversion of rutile to the nitride required carbon . The nitriding of ilmenite- carbon mixtures produced titanium nitride and elemental iron .

Jan 1, 1964

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concen¬tration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidaticn practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By L. M. Demers, R. E. Edelson, M. P. Rose, D. T. Superdock

The pulmonary alveolar macrophage is a major defensive cell which counteracts the invasive properties of bacteria and particles when these substances invade the pulmonary environment. Pulmonary exposure to coal dust particles is believed to activate these macrophages to release a host of d1emical mediators which can neutralize or contribute to the harmful effects of these dust particles. Our efforts have been concerned with assessing a specific family of mediator substances produced by the alveolar macrophage from arachidonic acid when these cells are in contact with activating substances such as coal dust. Metabolites of arachidonic acid produce a vast array of effects which can impact significantly on pulmonary function both with normal pulmonary events and with pathologic processes of the lung. Our studies demonstrate that isolated alveolar macrophages obtained from rats or guinea pigs cultured in vitro release appreciable amounts of the cyclooxygenase products prostaglandin E2 and thromboxane A2 and release significant amounts of the lipoxygenase products .5-HETE and LTB4. In the presence of l x 104 -1x10·7 g/ml of a coal dust suspension, alveolar macrophages from the rats and guinea pigs alters their pattern of arachidonic acid metabolite release. In the rat, exposure of alveolar macrophages in vitro to the higher concentrations of coal dust causes a significant reduction in PGE2, TXB2 and LTB4 in a 4 hour time course study. In contrast, macrophages from the guinea pig in response to coal dust had little change in TXB2 release, only a slight inhibition in PGE2 production and an initial stimulation in LTB.t release over the 4 hour time course. Cells from guinea pigs released considerably more TXB2 than the rat under these conditions while rat cells formed considerably more LTB4 than guinea pig alveolar macrophages. These findings support the following conclusions.

Mar 1, 1989

By L. L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P205, is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pct P205 and a P205 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1981

By Fred D. DeVaney

The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron are annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply. Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment. These may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the "betterment" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the in¬tent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods non well under way than of extension of boundaries by the city block plan of growth.

Jan 1, 1932