Search Documents

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By Paul M. Tyler

[This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of specified French possessions in Africa has been prepared from the best information available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. France controls large areas on the African continent, but the various Colonies and Dependencies are administered more or less independently. Algeria is under the direct jurisdiction of the Ministry of the Interior, and its mining laws are essentially the same as those of the mother country. Tunis and Morocco are attached to the Ministry of Foreign Affairs; separate digests of the mining laws' of these respective colonies have already been prepared by the United States Bureau of Mines. The present paper covers all other French territory on the continent of Africa except Somaliland, a rather small Colony including the port of Djibouti near the point where the Red Sea joins the Gulf of Aden. Available information indicates that the prospects of mineral production in this Colony, apart from salt and gypsum, are not at all encouraging.3]

Jan 1, 1933

By G. R. Hopkins, E. W. COCHRANE

The number of completed petroleum refineries in the United States continued to decline in 1937 , but the total capacity to process crude oil continued to increase . These facts were ascertained in the Bureau's annual canvass of refinery capacity as of January 1 , 1938 . Several important changes were made in the census questionnaire for January 1 , 1938 . First , the basis of reckoning cracking capacity was changed from cracking stock charged to cracked gasoline produced . Although this is a definite improvement , in that it is no longer necessary to consider the yield , it is unfortunate that the data for January 1 , 1938 cannot be compared with cracking - capacity statistics since 1925. Other changes or additions included separating capacity at operating plants into that actually operating and that closed down ; collecting data on capacity added or retired during the previous year ; breaking down idle capacity according to physical status ; and separating new capacity into that built for replacement and that built to augment existing capacity . Prior to January 1 , 1938 , the total capacity of an operating plant was listed as " operating " even though some stills might have been closed down ; furthermore , the only capacity reported as being under construction was that of new plants that were being built on January 1. To make the statistics clear , the totals for the United States as of January 1 , 1938 , are given on both the old and the new bases . On January 1 , 1938 , there were 551 completed plants compared with 572 the previous year . Ten new plants were under construction on that date compared with 11 the year before . The greatest number of completed plants recorded was 632 on January 1 , 1936 ; since then , competitive conditions , particularly in the East Texas field , have been instrumental in reducing the number of small independent plants . The total crude- oil capacity of the completed refineries on January 1 , 1938 , was 4,351,151 barrels , of which 3,970 , 196 barrels ( 91 percent ) represented the capacity in actual operation and 380,955 barrels ( 9 percent ) was shut down . The " shut -down " capacity ( 199,875 barrels on the old basis ) was the lowest since pre- depression days , chiefly because numerous idle East Texas plants were removed from the list . The new method of compiling the statistics sheds considerable light on excess crudeoil capacity , which has been the subject of considerable speculation in recent years . The highest daily average crude runs to stills reached in this country was about 3,460,000 barrels in September 1937. At that time , the total crude - oil capacity was about 3,925,000 barrels . This indicates that at peak operation the excess capacity was somewhat less than

Aug 1, 1938

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By L. E. Geyer

"The following list gives the title and author of various publications of the Ceramic Experiment Station, Columbus. Ohio, of the Bureau of mines, together with other ceramic publications of the bureau, which have been published in technical journals and by cooperating agencies. The list also includes the publications on ceramics which have been issued as bulletins, technical papers, or mimeograph Report of Investigations of the bureau.Papers Published in the Technical Press.The Effect of some Electrolytes on the Properties of Clays. Schurecht, H.G. Jour. Am. Cer. Soc., Vol. 1, #3, March, 1918.A Pycnometer Operated as a Volumeter. Schurecht, H.G. Jour. Am. Cer. Soc.,Vol. 1, #8, August, 1918.The Properties of some Ohio and Pennsylvania Stoneware Clays. Schurecht,H.G. Jour. Am. Cer. Soc., Vol. 1, #4, April, 1918.The Fusibility of Graphite Ash and its Influence on the Refractoriness of Bond Clay. Booze, M.C. Jour. Am. Cer. Soc., Vol. 2, #1. Jan., 1919.Behavior under Brass Foundry practice of Crucibles containing Ceylon, Canadian and Alabama Graphites. Stull, R.T. Jour. Am. Cer. Soc., Vol. 2, #3. March, 1919."

Oct 1, 1924

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

By E. D. Gardner

This paper is one of a series on mining methods and costs being published by the United States Bureau of Mines. In April 19.74 the St. Joseph Lead Co., at Atlanta, Elmore County, Idaho, was mining and milling about 225 tons of gold ore daily with a total force of 150 men. The mine, which comprises the old Boise-Rochester and Monarch properties, is at an elevation of about 6,000 feet. Snow lies on the ground about 5 months each year but does net interfere greatly with local operations. However, the road to Mountain Home, the shipping point 80 miles distant, passes over a high range and usually is closed by snow from about November 15 to June 15. Heavy supplies are brought in and concentrates trucked out during the summer. In winter the district is served by a biweekly mail plane and a passenger and express plane making 4 to 6 trips weekly. Mine timber is cut locally. A plentiful supply of water is obtained from a stream brought to the property through 7,500 feet of plume.

Jan 1, 1935

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By Raja V. Ramani, Sachin Shankar

"Re-entrainment refers to dislodgement of particles deposited by both atmospheric and nonatmospheric processes and their subsequent insertion into a flowing field. Formation of sand dunes, snow drifts, soil erosion and fugitive dust emissions are a few examples of the natural occurrence of re-entrainment. Re-entrainment studies have been done for the estimation of potential hazards from nuclear fallouts. The phenomenon of re-entrainment has been utilized for the cleaning of wafers and filters. Re-entrainment is associated with both surface and underground mining activities. However, studies on dust re-entrainment in mine atmospheres are limited. Understanding the re-entrainment phenomenon is important because dust particles lying seemingly harmless on the ground and adhering to numerous surfaces can get re-entrained and become a health and safety hazard.There are significant differences in the kind of re-entrainment encountered in underground mines and those in other fields of interest. These major differences are air velocity, direction of air flow, particle size, amount of particles, and time of exposure. While numerous studies have been done in other fields to identify the role of interacting variables and their contribution to the mechanisms of re-entrainment, no similar reported work is available for dust in mine atmospheres.In this paper, recent research efforts on re-entrainment are reviewed. The most suitable form of representing re-entrainment in underground coal mine atmosphere is presented. Various approaches to studying re-entrainment phenomenon in mines are also outlined.In the mineral industries, formation of dust particles of widely varying sizes is a natural outcome of the fragmentation required in mining the solid resources. Fine particles in mine atmospheres, particularly in the respirable size range, are a threat to the health and safety of the miners when present in high concentrations. In 1980 the National Academy of Sciences (NAS) Committee on the Measurement and Control of Respirable Dust in Mines recommended that the spatial and temporal characteristics (of fragments produced in coal mining) need to be understood so that the exposure of workers to the dust can be controlled. Recently several studies have been performed to understand the fundamental behavior of the airborne respirable dust in mine airways (Bhaskar, 1987; Qin, 1988; Polat, 1989; Bode, 1990)."

Mar 1, 1992

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964