Search Documents

These inspection standard have been prepared for use in the Federal inspection of strip mines producing, bituminous coal, anthracite, and lignite. This circular is a revision of the Safety Code for Strip Mining, which was prepared by the Bureau of Mines and employed as a guide for Federal inspectors. Numerous changes have been made in the original code to keep the in step with improvements in the industry. With continuing changes in mining methods and facilities some of these standards may become inapplicable and further revision may be advisable. Therefore, questions regarding these standards, and suggestions regarding new standards should be brought to the attention of the Bureau of Mines. Few States haves laws pertaining to strip mines, but where such laws do exist it is possible that some of the standards may conflict with them. In cases of conflict, the intent is not to advocate noncompliance with State laws, but to suggest reconsideration of such laws or safety orders.

Jan 1, 1946

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace,4 the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is, although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By R. R. Sayers

Carbon monoxide poisoning, as usually encountered, is an acute condition resulting from breathing atmospheres containing that gas. It is characterized clinically by headache, dizziness, weakness in the legs, increased respiration at first which later becomes irregular and depressed, collapse, unconciousness, and death; anatomically it is characterized by temporary changes in the red blood cells due to the combination of carbon monoxide with hemoglobin, and, in prolonged severe exposures, degenerative changes in various tissues of the body, especially those of the central nervous system. No race or nationality is immune or has a, special tolerance for carbon monoxide. From data at hand, it is known that both sexes are about equally susceptible. All ages are affected, but small percentages seem to have a more deleterious effect upon young animals and this is possibly true of children. Exercise, high temperature and humidity, and low oxygen content of en atmosphere increase the degree of poisoning for a certain concentration of carbon monoxide. Anything that lowers the physical fitness of a man, such as illness, overwork, or excesses of any kind, exaggerates the effects. More cases of poisoning from carbon monoxide occur in coal mines in the cold months of the year, because explosions take place more frequently during that period, also in homes where gas is used for beating purposes, and in garages from accumulation of automobile exhaust gases due to poor ventilation.

Jan 1, 1923

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By John K. Alley

Fibrous silicon carbide was produced by thermal decomposition of certain silicates contained in graphite crucibles. Induction heating was used to produce the necessary temperature and thermal gradients. Both green and white fibers were mainly the beta modification even though each color grew within a different temperature zone. Alpha silicon carbide, present in insufficient amounts for X-ray detection, was identified by electron diffraction. The white fibers formed in a zone between 1,365° and 1,634° C (±50° C). The green fibers (less contaminated) formed in a much more narrow zone between 1,650° and 1,672° C (±50° C). The average lengths and widths of microscopic fibers grown by this method were 1.5 mm/0.002 mm (white) and 1.2 mm/0.0035 mm (green); however, same fibers observed by electron microscope had cross-sectional measurements of 150 to 300 A. Both differential thermal analysis and thermogravimetric analysis showed that silicon carbide fibers oxidized in air at temperatures above 500° C. Fibrous silicon carbide was indexed as a cubic cell with the dimensions a = 4.358 A. The density calculated from X-ray data was 3.217 g/cm3.

Jan 1, 1963

By Louis C. Brichta

The Kline tract ?3.nd the Frey tract are two separate properties situated in the Wentworth district on the easterly edge of the Tri-State zinc-lead region (fig. 1). The Kline tract is in the southwestern corner of Lawrence County, Mo., and the Frey tract, 1 1/2 miles west of the Kline, is in the northeastern part of Newton County, Mo. A bureau Of Mines drilling project embraced work on both properties, but the amount of work done on the Frey tract was comparatively small. At the time of the project the Kline tract was under lease to the Wentworth Mining & Milling Co. The Surprise Mining Co. held the lease on the Frey tract. Underground workings on the generally flat-bedded are deposits of the Kline property-covered an area of-about 15 acres. No total metal-production records are available. In 1942-1943 the mine, operated by the Wentworth Mining & Milling Co., produced at an average monthly rate of 83 tons of 60-percent zinc concentrate derived from mining and milling 1,700 to 2,100 tons of ore. At the end of that period no significant amount of reserve ore was in sight. The gravity-flotation mill on the property was operating at about one-sixth capacity.

Jan 1, 1949

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By L. J. Froisland

The U.S. Bureau of Reclamation requested U.S. Bureau of Mines (USBM) assistance in developing design data for moving lead-zinc-gold tailings from their current location without disrupting the existing chemically stable conditions. This report presents results of USBM work in determining (1) the minimum required time to air dry the tailings to approximately 20 pet moisture under various drying conditions both in the laboratory and in the field, (2) the degree of oxidation or reduction that occurs during drying, (3) the effect of lime or cement addition before drying, and (4) the likely equilibrium conditions of the dried tailings after deposition at the new location. The limited number of tests performed by the USBM in the available time frame established trends in oxidation levels but did not provide absolute statistical validity of data values. All data from drying and oxidation testing are included in appendices to this report.

Jan 1, 2010

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973