Search Documents

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fifth of a series of reports giving the results of studies by countless under part (1) of the investigation. (See appendix.) This report covers Westmoreland County, Pa., which comprises parts of New Kensington, Freeport, Elders Ridge, Pittsburgh, Greensburg, Latrobe, New Florence, Johnstown, Brownsville, Connellsville, Donegal, and Somerset quadrangles. (See fig. 1.) A short resume" of the chemical and carbonizing properties of the coals are included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By W. W. Adams, T. D. Lawrence

"The National Safety Competition covering the calendar year 1934 was the tenth yearly safety contest conducted by the United States Bureau of Mines. Participating in the competition were 334 mines and quarries in 38 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies ""Sentinels of Safety.""Since these annual contests were begun 10 years ago by the United States Bureau of Mines the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the prevention of accidents has been achieved, as is indicated by an almost constant downward course in toe accident-frequency rates for the contest group as a whole during the past 10 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the decade and a downward trend during the latter part of the period except in 1930 and 1934; in each of those years a disastrous explosion with abnormally heavy loss of life occurred at the property of one of the participating companies.Because of the abnormal nature of the major disaster in a bituminous-coal mine in 1930 and 1934 the accident-severity rates for the bituminous group for those years are not strictly comparable with the rates for other years. The rates for bituminous mines for 1934 in the present report have therefore been computed on two bases; first, to exclude the record of the company that suffered the disastrous explosion and, second, to include the record of this company. The first rate represents the normal experience of the bituminous coal companies unaffected by the disaster and is therefore more indicative of the real trend of the accident rates for this class of mines from year to year. The latter rate shows the actual experience of all bituminous mines in 1934. The report of the competition of 1930 likewise showed the rates for the bituminous group as computed both with and without the disaster that occurred that year.The National Safety Competition is conducted by the United States Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the facts contained in the accident reports which the competing companies furnish to the Bureau to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest."

Jun 1, 1935

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By L. H. Banning

The Bureau of Mines conducted pioneering batch and laboratory cyclic tests that simulated plant operation in developing a procedure for acidulating phosphate rock with fluosilicic acid. Both high-grade deslimed phosphate rock and low-grade phosphate rock samples were treated. The most promising results were obtained by acidulating des limed high-grade material. In a series of seven cyclic tests, 85.4 percent of the P20S was recovered in solutions. The average P2O5 content of the phosphoric acid-monocalcium phosphate solutions of the first step was 156 grams per liter, and the average fluorine content was 4.7 grams per liter. Residues had an average fluorine content of 30.7 percent and contained 83.9 percent of the total fluorine in the charge materials. Some fluorine was lost by volatilization.

Jan 1, 1975

By L. K. Weaver

The purposes of this Bureau of Mines report are to review the history of the domestic offshore hydrocarbon production; to project offshore oil and lease condensate production from 1971 through 1985; and to show the impact of offshore development on the onshore segment of the petroleum industry. Since 1954, offshore production has provided an increasingly larger portion of the domestic oil production. Domestic offshore oil and lease condensate production has increased from about 2.0 pct of the U.S. total in 1954 to 16.7 pct in 1970. Likewise, marketed gas production has increased from 1.0 pct of the U.S. total in 1954 to 15.0 pct in 1970. The past performance of exploration, leasing, development, and production of the offshore petroleum industry was used to make projections of offshore oil production. A comparison between onshore and offshore operations was also made. Assuming a tentative Department of the Interior offshore leasing schedule is completed by 1980, the authors estimate that by 1985, about 30 pct of domestic crude oil and lease condensate production from the lower 48 States will come from offshore areas. Currently, leasing of Federal offshore areas has been delayed due to environmental considerations. The rate at which off-shore hydrocarbons will enter the energy market will depend, to a large extent, on how soon environmental considerations are resolved. Assuming that offshore leasing will resume in the near future, U.S. offshore production of crude oil and lease condensate should be about 934 million barrels in 1985.

Jan 1, 1973

By V. E. McKelvey

Any discussion of growth and future requirements has to begin with people--both their number and their needs. Both have been rising ever since any American can remember. Together, the number of people, which has been increasing rather modestly, and their wants and desires for material things, which have been increasing very sharply, seemed to have comprised a growth imperative in mineral consumption in the United States, especially during the last several decades. While the Nation's birthrate is now well below the replacement rate and still falling, the built-in momentum of the post-World War II population boom will continue to be felt well into the 21st century. Even using the modest projection of a 0.8 percent yearly increase, we are still looking at the possibility of 265 million Americans being around by Year 2000.

Jan 1, 1975

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By P. G. Clites

The Bureau of Mines developed techniques for induction melting of titanium in a split, water-cooled copper crucible. Calcium fluoride, which was used as an inert slag cover during melting, formed an insulating layer of solid slag between the ingot and the crucible wall. This thin layer of slag effectively insulated the ingot from the crucible and prevented the molten metal from shorting across the slits between adjacent segments of the crucible. The technique provides a means of melting loose titanium sponge and scrap and eliminates the need for fabricating a consumable electrode. This report describes the equipment developed and compares ingots produced from two varieties of titanium sponge, from titanium scrap, and from previously melted titanium with ingots prepared by vacuum-arc melting and electroslag melting. A melting scheme was also proposed and evaluated whereby loose titanium sponge was consolidated into a first-melt ingot for vacuum-arc remelting.

Jan 1, 1969

By E. C. Lane

[This is the eleventh in a series of reports on properties of commercial motor fuels made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data, on motor gasolines sold during the winter of 1935-36.3/ The present report presents analytical data for 2,020 samples, reprecenting the products of approximately 120 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data averaged the Pacific Coast Technical Group before being submitted and' are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasoline each group has been averaged separately. The number of samples, items, and old brands comprising each group, exclusive of the of the Pacific coast, axe as follows: Regular price, 1,071 samples, 29 items, and 77 brands; premium price, 608 samples, 235 items, and 72 brands; third-grade gasoline, 341 samples, 196 items, 78 brands. The meanings of these terms as used in tae surveys are as follows:]

Jan 1, 1941

By E. C. Lane

[This is the eleventh in a series of reports on properties of commercial motor fuels made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data, on motor gasolines sold during the winter of 1935-36.3/ The present report presents analytical data for 2,020 samples, representing the products of approximately 120 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The number of samples, items, and brands comprising each group, exclusive of the of the Pacific coast, axe as follows: Regular price, 1,071 samples, 29 items, and 77 brands premium Price, 608 samples, 235 items, and 72 brands; third-grade gasoline, 341 samples, 196 items, and 78 brands. The meanings of these terms as used in tae surveys are as follows: Sample: The individual sup of gasoline o1 obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1964-65. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By G. L. Oldright, Virgil Miller

"This paper is the ninth 4 of a series on smelting in the lead blast furnace, and the fourth on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSThe authors wish to express their appreciation to Stanley A. Easton, Frank M. Smith, and A. F. Beasley, and to their staff for the whole—hearted cooperation that made it possible to obtain the data in this publication at the Bunker Hill smelter, Kellogg, Idaho.INTRODUCTIONIn tie account written of the conditions obtaining at the tuyere zone in the blast furnaces at Tooele (R. I. 2965) the authors gave references to articles covering (1) the effect of temperature on the equilibrium 2C0 - CO2 + C, (2) experimental work that has been done on learning the gases existing at various elevations in columns of burning coke, (3) extension of this work to the tuyere zone of an iron blast furnace, and (4) the paper itself gave similar analyses of the gaseous oxides of carbon at the tuyere zone of a lead blast furnace and showed the temperatures obtaining there. There were also references in the above paper to the literature on (5) how the lead compounds likely to be present might be ex¬pected to react. A careful study of the original articles selected as references will give a good background for the present work.The following very brief recapitulation may be convenient before considering the tuyere zone in the blast furnaces at Kellogg. The ""producer gas reaction"" (1) of course goes to the left at increasingly higher rates of speed with increase of temperature. When air is blown upward through a grate and a column of hot fine coke alone, oxygen as such penetrates from some 2 to 3 inches only, under the conditions obtaining as to the amount of surface exposed per unit volume of air. When air is blown at about 20 pounds pressure through the tuyeres in the side of an iron blast furnace into a column of coarse coke (plus furnace charge) it may penetrate for 30 inches before the oxygen is entirely used, burning first largely to CO2. Within wide limits, the rate of feeding air into the furnace has practically little effect on the composition of the gases obtaining in the fuel bed of fine coke, this being true particularly of the gases leaving the bed. Some 10.5 inches above the grate the gases contained 22 per cent of CO by volume, and a little further up the CO2 had practically disappeared. This gave the familiar three zones in both the iron blast furnace and the gas producer; in order of entry of the air, in the first the oxygen burned largely to CO2, in the second the CO2 was reduced to CO, and the third the CO2 was practically absent. In the furnaces at Tooele, conditions were somewhat erratic but the first two zones were present, there being, however, no zone in which CO2 and 02 were both entirely absent."

Apr 1, 1931

By E. C. Lane

This report presents the results of the Bureau of Mines' twenty-first semiannual survey of motor gasoline marketed in the United States. The 12 cities in which samples were collected have teen chosen as representative of the more important marketing territories, as it is obviously impractical to obtain a sample of every gasoline sold in the entire country. The survey reveals that the motor gasoline which is being marketed in the United States this winter is decidedly more volatile than that sold a year ago. Samples from all cities show a decided improvement in volatility except those from Laramie, Wyo., which show a small decrease in volatility.

Jan 1, 1930