Search Documents

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959

By S. F. Mauser

This report describes the study of factors which affect medium voltage (661 - 1000 volts) trailing cable splices used in underground coal mines. Improvements in quality, dependability, and design of splice kits and shop splices are presented in the study results and recommended guidelines and regulations. Recommended research programs are included which describe approaches for development of the recommended guidelines and regulations for medium voltage trailing cable splices. The basis for the conclusions and recommendations presented in this report is included in three appendices which describe a survey, splice examination, and general requirements development prepared during the progress of this study.

Jan 1, 1977

By Sumner M. Anderson

THE ENORMOUS contrast between the mineral economy of Cuba in 1963 and in 1958 was the result of the overall Political changed to which the total economy of the country was intimately lined. Creation of the Cuban Mining Institute (Instituto Cubano de la Minería) to direct all mining activities in the country was an early act of the new Government after the revolution on January 1, 1959. During the next 2 years, the Government confiscated foreign holdings,2 including Unite States investments exceeding $1 billion in value. Foreign mining and metallurgical technicians-predominately from Communist areas-were brought in to reorganize the mineral industries. On January 3, 1961, diplomatic relations between Cuba and the United States were severe and then on May 2, Cuba announced its full-fledged membership in the so-called Communist Bloc. Fifty-four international treaties assured Cuba of Communist economic support, technical and financial assistance, machinery, raw materials, and manufactures. The Soviet Union agreed to buy some Cuban mineral products, and Czechoslovakia stated that it would buy all mineral production offered for the next 20 years, but in both cases at prices said to be much lower than the world market. The mineral productivity segment of the mineral economy during and since the period of political metamorphosis, has withstood the political disruption better than has the economy as a whole, but with no direct measure of the magnitude of its cost. The overall economic record is marked with steady deterioration; the annual average per capita income has dropped from $374 in 1957 to $185 in 1963, when Cuba's deficit with the Soviet Union alone reached an admitted $1 billion.

Jan 1, 1964

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By Edward P. Barrett

The production of sponge iron is one of the earliest arts in the metal¬lurgy of iron and steel. The idea of producing iron direct from ore at temperatures lower than the melting point of, the iron has persisted throughout the centuries. The purpose of this paper is to present a general picture of the methods, proposed or tried within the past 100 years, for producing sponge iron by treating hot ore with heated reducing gases. The abundant literature has been abstracted, and quoted freely. Publications concerning more detailed information on the various methods are referred to in the footnotes and in the bibliography.

Jan 1, 1949

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By W. W. Adams

The year 1937 was signalized by increased employment in the metal-and nonmetal-mining 4 industry of the United States. Measured by the number of men working, there was a 17-percent gain in employment compared with 1936. In total number of man-hours worked at all mines, the gain was slightly over 18 percent. Hazards connected with mining resulted in more accidents to the workers than in 1936, but the increase in number of accidents caused only a slight rise in the accident rate because of the much larger increase in the number of man-hours worked. In fact, the fatality rate per million man-hours of exposure was lower in 1937 than in 1936, but the rate for nonfatal injuries increased slightly.

Jan 1, 1940

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By William C. Cooley

Data on equipment and components which have been used in hydraulic mining experiments, tests, and operations were collected from the literature. Also data were obtained from U.S. manufacturers and suppliers of equipment which is potentially applicable and available in the U.S. for hydraulic mining. The data have been divided into 24 main categories (see the following page) and have been assembled on two-page data sheets which follow. Wherever possible, drawings or photographs are included immediately after each data sheet.

Jan 1, 1975

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

In 2005, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 922 underground (6.3%) and 13,744 surface (93.7%) mining operations.1

Jan 1, 2008

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981