Search Documents

By Irvin G. Burough

Andros Analyzers Incorporated has designed and built two prototype continuous methane monitors capable of being mounted on a mining machine'. These instruments were designed for in-mine safety use. The monitors incorporated an NDIR optical/electronic analyzer design in which the response to the sample gas (methane in air) was achieved by synchronous detection and measurement of the amplitude oscillations of the trasmitted energy from an infrared source caused by the pressure modulation of the sample gas within the optical cell. Zero and span stability were to be achieved by the amplitude modulating of the infra-red source and using detected signal to correct for optical/electronic system variation. This design effort was to simplify and reduce the cost of the major components while eliminating the need for daily calibration. This report is the final report on this effort.

Jan 1, 1981

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By Boyd Guthrie

As the American petroleum industry surveyed its position in early 1937, it had many reasons to be optimistic concerning its future. The industry had emerged successfully from the depression, and for the first time since 1929 it had produced over one billion barrels of crude oil in a single year. The demand for gasoline and fuel oils was up, and reserves of crude petroleum and production capacity seemed adequate for the future. Although production of crude oil dropped slightly in 1938, the oil industry was still in a good position with respect to its supply of raw material, which improved economically in 1939 with the decrease of crude-oil stocks in storage above ground. However, by 1940 a threatening cloud (the invasion of France and its rapid surrender) had appeared on the horizon. This aroused Somme fears as to the industry's immediate future, and these fears were intensified the following year when the United States entered World War II. As the war progressed, more and more ships, planes, and vehicles were produced, and the problem of obtaining enough liquid fuels to supply them intensified. Hearings were held in August 1943 before a subcommittee of the Committee on Public Lands and Surveys of the 78th Congress to determine the advisability of passing legislation to promote the development of synthetic liquid fuels.

Jan 1, 1951

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By W. G. Phillips

This report presents results from a study whose objective was to evaluate noise control options for existing equipment used in metal and non-metal processing plants. This equipment performs 3 basic functions, crushing, grinding to a point where the product can be liberated from the waste, and agglomeration A the product. Specifically, the study was directed towards taconite processing since the extreme hardness of taconite results in high noise levels and in considerable maintenance of the processing equipment. Both of these factors make this process a very challenging noise control task. Plants processing other ores use similar equipment, consequently the results of these studies should he applicable to a wide variety of plants. The report presents the source diagnosis and potential retrofit noise control treatments for fine screens, mills, crusher sizing screens, and vacuum disc filters. Estimates are make of the noise reduction from each treatment. The report concludes with recommendations for future research on each piece of equipment.

Jan 1, 1978

By Henry Kreisinger, John Blizard, B. J. CROSS, C. E. Augustine

This report gives the results of 26 tests of a four-pass Edgemoor boiler fired with powdered coal at the Lakeside station of the Milwaukee Electric Railway & Light Co. The tests were made by the fuel section of the Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation and the operating department of the Milwaukee Electric Railway & Light Co. The object of the tests was to determine the thermal efficiencies and capacities obtainable by burning powdered coal under large central-station boilers, and the possibility of operating such boilers continuously at high efficiency and capacity without destructive effect on the furnaces and without difficulties in refuse removal. In any system for burning pulverized coal the furnace is the most important part because, to justify the cost of pulverizing, the powdered coal must be burned with higher efficiency than coal fired with mechanical stokers. In other words, it is the furnace that by giving higher thermal efficiency must pay for the installation, maintenance, and operation of the pulverizing equipment. No matter how simple the apparatus for the preparation of pulverized coal may be, or how simple the pulverizing process, unless the furnace is so designed that it can be operated continuously with high thermal efficiency, the whole system is a failure. For high thermal efficiency the coal must be burned almost completely with low excess air. But low excess air and complete combustion give high furnace temperature, which in turn causes erosion of the furnace lining and fusion of the ash; and removal of the fused ash is difficult. The necessity of complete combustion with low excess air thus brings with it these two important problems in the design of a furnace for burning powdered coal: 1, Prevention of erosion of the furnace lining; 2, easy removal of refuse from the furnace. For the purpose of solving these problems, the boiler tested was equipped with a furnace having hollow walls, through which about 60 per cent of the air needed for combustion passed before it entered the furnace. By passing through the hollow walls, the air cooled the furnace lining and prevented excessive erosion. A water screen was placed in the furnace about 3 feet above the bottom to keep the refuse deposited at the bottom from fusing and to make its removal easy. The design of the furnace, water screen, and burners was based on the experience gained in the previous cooperative tests1 with a smaller furnace, experimental water screen, and burners at the Oneida Street station of the Milwaukee Electric Railway & Light Co. The boiler tested had 13,057 square feet of heating surface. It was one of eight boilers fired with powdered coal, and was designated as boiler No. 8. The Lakeside station is the largest central station in the world that burns powdered coal exclusively. The coal used in the first five tests came from Illinois. The fuel in the other tests -:vas a mixture of Illinois and Pittsburgh coals.

Jan 1, 1925

By C. Özgen Karacan

In longwall development mining of coal seams, planning, optimizing and providing adequate ventilation are very important steps to eliminate the accumulation of explosive methane-air mixtures in the working environment. Mine operators usually try to supply maximum ventilation air based on the capacity of the system and the predicted need underground. This approach is neither economical nor safer as ventilation capacity may decrease in time depending on various mining and coalbed parameters. Thus, it is important to develop better engineered approaches to optimize mine ventilation effectiveness and, therefore, to ensure a safer work environment. This study presents an approach using coalbed methane reservoir modeling and an artificial neural network (ANN) design for prediction and optimization of methane inflows and ventilation air requirements to maintain methane concentrations below statutory limits. A coalbed reservoir model of a three-entry development section, which is typical of Pittsburgh Coalbed mines in the Southwestern Pennsylvania section of Northern Appalachian Basin, was developed taking into account the presence and absence of shielding boreholes around the entries against methane inflow. In the model, grids were dynamically controlled to simulate the advance of mining for parametric simulations. Development and application of artificial neural networks as an optimization tool for ventilation requirements are introduced. Model predictions are used to develop, train, and test artificial neural networks to optimize ventilation requirements. The sensitivity and applications of proposed networks for predicting simulator data are presented and discussed. Results show that reservoir simulations and integrated ANN models can be practical and powerful tools for predicting methane emissions and optimization of ventilation air requirements.

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By J. H. Wiggins

The evaporation of crude oil without doubt causes one of the largest single losses to which the oil is subjected after it is taken from the ground. The few days during which crude oil is stored on the lease before being taken by the pipe line, causes an aggregate loss per year from evaporation estimated at 122,100,000 gallons of gasoline in the Mid-Continent field alone. This has a value, at 22 cents per gallon, of $26,880,000 and represents about 3 per cent of the total gasoline produced in the United States from all fields and all sources. The following table shows this in more detail:

May 1, 1920

By George H. Holmes

This paper is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . It describes briefly operations and mining methods at the Basic Refractories , Inc. , brucite deposit , the only commercial deposit of brucite in production in the United States . The mine and crushing plant are in secs . 26 and 35 , T. 12 N. , R. 36 E. , M. D. B. & M. , northwestern Nye County , Nev . , 1 mile east of Gabbs and about 33 miles northeast of Luning , a town on the Mina branch of the Southern Pacific Railroad and U. S. Highway 95. ( Figs . 1 and 2 ) .

Dec 1, 1949

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

By J. R. McVey

A 10-channel automatic data acquisition system has been designed and environmentally packaged for use with underground strain-gage applications and associated instruments. The system uses commercially available components and is assembled in two plastic enclosures. Environmental control is provided through a specially designed (compressed-air) air-conditioning system and water-resistant cabling. Accuracies of 0.01 pct and resolution of 1 µV have been obtained in underground tests.

Jan 1, 1973

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

Our mission is help ensure our country has an adequate, dependable supply of minerals and mate al to meet its national security and economic needs at acceptable social, environmental, and economi[c] costs. We do this by promoting and encouraging private enterprise in the development of viable and stable mineral industries through the transfer of innovative extraction, processing, recycling, an environmental technologies; our use of cooperative partnerships with industry, academia, an government; our timely, authoritative worldwide mineral intelligence; our advocacy of public policies based on good science and sound economics.

Jan 1, 1994

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By G. W. Birge

Carbonizing properties of the principal coal beds of Perry County, Ky., are described in this Bureau of Mines report. Seven samples, representing the Hindman, Flag, Haddix, and Fire Clay beds, were carbonized by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Carbonizing properties of blends of Flag and Fire Clay coals, with 20 and 30 percent Pocahontas No. 3 low-volatile coal from McDowell County, W. Va., also were determined. Expanding properties of the Flag and Fire Clay coals and their blends were determined in the Bureau of Mines sole-heated oven. The Perry County coals tested are high-volatile A bituminous in rank and, with the exception of the Hindman-bed sample, which contained excessive sulfur, were chemically suitable for metallurgical use. The three coals tested in the sole-heated oven contracted less than normal for Appalachian coals of similar rank, Blending the Fire Clay and Flag coals with 20 or 30 percent low-volatile coal increased coke strength appreciably but increased the expansion beyond normal limits for industrial blends.

Jan 1, 1962

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977