Search Documents

By C. Pelley, S. Kelebek, G. Kunzel, P. Katsabanis

Small blocks of granodiorite have been subjected to blast loads from a single borehole and from a series of boreholes detonating at various timing intervals. The damage of the blocks was assessed through P-wave velocity monitoring, measuring the change of the point load strength index of the rock after dividing the large blocks into smaller ones and measuring the work index of the material at different distances away from the blasthole. Numerical modelling with the AutodynTM code enabled visualization of damage. It was shown that damage is optimum at a small delay time between successive holes while it drops rather drastically after this point.

Jan 1, 2003

By August Ferraz Ribeiro, Guilherme Dias Mendona, Paula Henrique Lisboa, José Silvio Corsini

Correct slope adhesion is related to the conformity of the slope’s real geometry to slope planning. It is very important in mining because slope design has economic and safety implications. Slope design conditions can interfere with mining waste and ore proportion. Without a correct wall, the development of the mine can be hindered, which can reduce the amount of ore available. Furthermore, correct slope design reduces the possibility of melting and allows traffic with equipment and people in the mine. However, defining the wall is a more complex work as the characteristics of the rock require the use of blasting techniques. Therefore, Enaex Mining Technical Solutions (EMTS), in partnership with the engineering team at the Chapada Mine, at Lundin Mining, has developed this study in order to increase slope adhesion. The basis of this study is a near-field vibration test, which enables the creation of vibration attenuation law, and a seed wave damage model has allowed the characterization of the rock present at the Chapada Mine. Then, we could compare the model result to the real slope adhesion achieved with the buffer technique used in the mine. Therefore, it was possible to relate the real result to the model result.

Feb 6, 2023

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By W B. Gregg

"A review, update, and expansion of Thiokol’s presentation at BAl’s Fiih High Tech Seminar titled ‘ADetonator - An Era of Precision in All-Electronic Detonators” is provided herein (and should be considered as a supplement to that publication). Thiokol is currently in the development and field evaluation phase of activities for our ACCUBLASTTM all-electronic detonator. The ACCUBLASTTM detonator uses a semiconductor bridge (an electronic match) in place of a conventional hot wire to initiate a safer, less sensitive material, titanium subhydride potassium perchlorate. The device is programmable to provide blast delays in one millisecond increments ranging from 1 to 500 milliseconds. The ACCUBLASTTM detonator combines an all-electronic programmable timer coupled with a semiconductor bridge to ensure detonation timing accuracy with +I00 microsecond precision. Initial development and field testing have been completed. These tests have verified ACCUBLASTTM detonators’ precision."

Jan 1, 1995

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By L C. Taylor, H U. Lesiste

This paper provides a preliminary description of the properties of the output pressure (shock) wave of an end initiated, cylindrical charge of low height to diameter ratio in saturated sand. The properties of primary interest are the pressure wave velocity, peak pressure and rate of rise of peak pressure to within 1.4 charge diameters from the output end of the charge. The behavior of these properties is seen to be quite different from their behavior at more customary ranges in water.

Jan 1, 2013

By D. Scott Scovira, Rick Webber

The Iron Ore Company of Canada [IOC] is a global leader in Arctic mining applications, and the blasting crew have something to be very proud of. On Wednesday 21 Dec 2005 at 3:28 PM the largest single bench blast in the company history was detonated. The successful firing of this 5.0 million tonne [5.5 million ton] blast surpassed the previous company record of 3.8 million tonnes [4.18 million ton].

Jan 1, 2008

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Jaco van den Berg, Dr. Todor Petrov, Dr. Josh Calnan, Dr. Jhon Silva

This paper shows and reviews the similitudes and differences in explosions generated by high explosives and gas explosions, the reasons why gas explosions are difficult to replicate using high explosives, and the considerations when performing explosive testing using methane gases and coal dust.

Feb 1, 2020

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By Jeffrey W. Lin, Larry B. Weston, Jonathan D. Abbott, Jordan L. Arthur

Hydrocarbon fuel oils are one of the main components of ammonium nitrate-based explosives, including ANFO (Ammonium Nitrate-Fuel Oil) and emulsions. While a wide variety of fuels can, and have, been used in the manufacture of ANFO and emulsion products, No. 2 diesel, particularly dyed, off-road diesel, is widely used due to its ready availability and use in fueling mining equipment. However, a number of alternatives to standard diesel have been introduced over recent years, namely, biofuels, ‘high-performance’ diesels, and renewable diesels. The pressure to adopt these alternative fuels come from a variety of sources, such as initiatives to reduce carbon footprints, increased lifetime of equipment, and cost-advantages from tax credits. While these factors may provide a very real benefit to the mine site, a consideration that is often missed is how the use of these fuels can impact the formulation and characteristics of the ammonium nitrate-based explosives. Herein will be presented a discussion of these alternative fuels from a chemical perspective as well as the results of several studies focused on how the inclusion of various alternative diesels influences the production and performance of ammonium nitrate explosives. ANFO and emulsion were manufactured using representative fuel sources and studying in terms of the manufacturing parameters, shelf-life, interaction with other chemicals using in mining explosives. Detonation data was then collected for these products and compared to the behavior of products made with standard diesel fuels.

Jan 21, 2025

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By R Malo, A Yetter

The use of large diameter blastholes for underground mining began approximately twelve years ago and are now routinely employed in a variety of ore types and stope designs. These large boreholes, ranging in size from 4 1/2 inch to 8 inch diameter, were first utilized in the same fashion as in open pit bench drilling. However, a variety of changes quickly followed in order to accommodate the unique conditions encountered while using a blasthole sloping method.

Jan 1, 1984

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By Paul Klaric, Nicholas Bodley

Every blasting engineer or professional can attest to the age-old conundrum of obtaining accurate hole information on a large scale prior to loading explosive charges in a blast hole. Even though the benefits of QA/QC are well known and documented and are becoming increasingly important when digitizing and automating mining operations, the QA/QC process itself has not changed significantly over generations. The current methods where operators deploy measuring tapes of variable standards recording their subjective assessment of hole length on a paper blast map or manually transcribing to a tablet, are unreliable and non-auditable. Additionally, the process in its current form is time intensive, obtaining only moderate results and benefits, making it difficult or impossible to resource in today’s tight labour markets. Often only two data points, depth, and water presence, are captured when visiting the hole resulting in a high cost per bit of data. For these reasons, the process is seldom done on a large scale, let alone integrated. The QA/QC process in its current shape is a gap that will need to be addressed if autonomous blasting and mining is to become a reality.

Feb 6, 2023