Search Documents

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by using electronic detonators. The Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast fragmentation measured with the SPLIT image analysis system to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed, and the powder factor increased, to maximize fines. However, a growing number of studies have shown that the use of electronic detonators can lead to increased fragmentation and greater muckpile uniformity, providing an alternate means of increasing primary breakage by blasting. Unfortunately results in the literature rarely quantified the changes to the fragmentation distribution. The measured gyratory crusher fragmentation of 2,750,000t of ore was used to compare stockpiles constructed from shots using pyrotechnic detonators to those using Orica i-kon electronic detonators. In the first stage of the study, stockpiles shot using 25 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using the same inter-hole timing with electronic detonators. In the second stage of the study, stockpiles shot using 17 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using 8 ms inter-hole timing with electronic detonators. When electronic detonators were used with the inter-hole timing kept constant, fragmentation uniformity was slightly increased, but mean fragment size increased by 20%. When electronic detonators were used with faster inter-hole timing, fragmentation uniformity was slightly reduced, but mean fragment size decreased by 30%. Modeling was used to determine the SAG mill throughput which could be expected from this change in fragmentation to determine the pairs of pyrotechnic and electronic blast pattern geometries that would provide similar throughput. The economic benefit from the electronic detonator shots was calculated to assist in determining the optimum blast designs for their use.

Jan 1, 2010

By R W. Thomas

This paper explores the possibilities of generating radical improvements in the drilling costs and productivity of blastholes through the efforts of integrated teams as opposed to traditional customer/vendor relationships.

Jan 1, 1996

By Mark Fritzen

Drilling and blasting near residential or business inhabited areas may expose people to blast induced vibration. Many of these people have never been exposed to blast vibration and airblast which can cause a variety of reactions ranging from indifference to anger. Blasting contractors seeking to minimize the impact of blasting to neighbors of the project will plan for a public relation plan which begins at bid time. The public relations plan cost will be included in their proposal and a variety of methods may be included including, door to door contact, letters, pamphlets, telephone calls, and the use of an independent consultant to conduct a pre-blast survey. By raising the awareness of neighbors to a blasting project the blasting contractor may reduce the anxiety and stress of unannounced blasting vibration and airblast. This helps everyone associated with the project from the project owner(s) to the blasting contractor.

Jan 1, 2000

By (Journal for the Fields of Gunpowder and Explosives) Germany (1914 Issues)

RBH Note: The following items are a deviation from the usual content of these articles, but I thought they were kind of interesting from an historical point of view (other than just explosives-history historical.) The interesting things to me are the military-related products, keeping in mind that World War I didn’t start until August, 1914, and then it was kind of an accident of political alliances gone awry. Obviously companies in Germany saw it coming. Of course, all the ads also included dynamite and safety explosives for mining and tunneling as well as the military items.

Jan 1, 2015

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By Nikolaos Petropoulos, Ulf Nyberg, Daniel Johansson

A series of signature boreholes were blasted to observe any difference between confined and free face blasts. Four geophones were used to capture the compressive wave. The conventional approach, i.e. the calculation of vectorized peak particle velocity (vPPV) did not show any difference. Also a wavelet transform was tested.

Feb 1, 2020

By James T. Ludwiczak

Drilling and blasting in a Karst (sinkholes and mud seams) environment has long been a problem for blasters, miners, quarry operators, contractors, and developers. While one cannot change the geological conditions, one can take some measures during the bidding process and the initial preparation of the blasting program to help reduce some of the problems. During the geotechnical investigation and developing the test/core drilling grid, the owner/developer needs to take some additional measures that will provide important data to the blaster to help reduce the problems associated with blasting this type of geology. The owner/developer must also understand that, due to the geologic conditions, the results of the blasting will not be ideal and there may be additional blast-related costs. If provided the proper geologic data, the blaster can develop drilling patterns and blast designs that will help reduce some of the more problematic areas.

Jan 1, 2005

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Sandra Penttinen

There are several ways to get a positive reaction from abutters to blasting projects. When you need to enter structures to conduct a blast-blast inspection, the impression you make on the structure owner must be positive from the very start. Your public relations with neighbors is the key. The purpose of all communications with persons residing near planned blasting operations is to educate structure owners as to what will take place during the blasting operations, to explain that safe blasting practices will be followed and vibration and airblast limits will be imposed to protect surrounding structures from damage. Once access into structure is obtained, the structure owner can be shown, by careful documentation, all existing cracks and defects in the structure prior to blasting and construction. The objective of your visit and all communications is get your foot into the door and win the confidence of the structure owner so that he or she understands blasting will not compromise the structure.

Jan 1, 2005

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Joel Chipana, Roberto Laredo, Benjamin Cebrian

Ring blasting is a common production method in underground metal mines. As a drill and blast process, it presents particular features that do not correspond with bench blasting in open pit or underground mining.

Jan 1, 2017

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

Explosive manufacture, handling and transportation is hazardous and special precautions should be taken while manufacture, handling and transportation. Various regulations and rules defined in explosive act and factories act of India are discussed in this communication. General process control measures during the manufacturing of different types of explosives are also dealt in detail. Various processes hazardous in manufacture of various explosives like slurry explosives, PETN, detonators, styphnic acid, lead azide and lead styphnate and special precautions to be taken during the manufacture of the above explosives are also discussed.

Jan 1, 2007

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By Viktor Aranovich, Thomas E. Brown

The Almalyk Integrated Mining and Metallurgical Plant is located near Tashkant in Uzbekistan and is one of the former Soviet Union's largest copper producers. Almalyk consumes about 10,000 metric tonnes of explosives annually and expects this requirement to double by the end of the century as they implement a program to boost mine output.

Jan 1, 1998

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012