Search Documents

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By R. Van Hille, S. Lacour, A. E. Lewis, K. Peterson

"This paper compares thermodynamic modelling results with those obtained for copper sulphide removal from aqueous solution in both continuous and batch experiments at laboratory scale. Sulphide precipitation has been demonstrated to be an effective method for heavy metal removal. The advantages are the high degree of metal removal at low pH, low quantities of sludge formation, the ease of de-watering and low reactor retention time due to high reactivity of sulphides. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines, which are difficult to remove.Theoretical modelling was carried out using ASPEN Plus™ and OLI systems Inc ESP process. Both simulators were used to calculate copper sulphide recovery and residual aqueous copper concentrations as a function of pH. The predictions were then compared with experimental results. Both simulations predicted that all of the inlet copper would precipitate as sulphide CuS(s) over the entire range of pH and sulphide: copper molar ratios investigated. The simulation results were strongly influenced by the number of chemical species and the nature of the thermodynamic data taken into account in the model.The continuous experimental studies were carried out in a fluidised bed reactor (FBR). Copper sulphate was reacted with sodium sulphide and the solid precipitated directly onto the pellets in the FBR. The use of sulphide was motivated by high sulphate levels in local acid mine drainage and the ultimate integration of the metal removal process with a biological sulphate reducing process that produces an aqueous sulphide stream.A maximum dissolved copper removal of 99.6% (AAS analysis) and a total removal efficiency of 95.8% (dissolved copper minus fines) were achieved. Stoichiometry of the precipitate was determined from SEM/EDAX analysis (atomic percentages) and was close to 1/1, irrespective of the operating conditions."

Jan 1, 2003

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By Olga D. Khmelnitskaya

The paper presents the results of research on the development of gold recovery technology from oxidized gold-copper ore of one of deposits in Russian Federation. Gold and copper grades in the ore are 9.5 g/t and 0.4%, respectively. Various options of flowsheets, such as direct cyanidation, thiourea leaching, flotation and gravity concentration followed by subsequent cyanidation of con-centration products, were tested. It was established that gravity-cyanidation technology with filtra-tion leaching tails and the use of solutions in the recirculation is the optimal option for ore treatment. The proposed flowsheet provides gold recovery for 91.0% at NaCN consumption 2.5 kg/t ac-cording to the results of pilot testing. Ammonia-cyanide gold leaching was also examined. In comparison with cyanidation, gold leaching solution in system NaCN-NH4OH-(NH4)2CO3 allows NaCN consumption to be reduced three times from 4.5 kg to 1.5 kg per 1 ton of the ore and provides the same gold recovery. Based on the laboratory and pilot plant tests results of gravity-cyanidation technology of gold dissolution, process design criteria were developed.

Jan 1, 2014

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Przybycien Krzysztof, Tumidajski Tadeusz

"Materials being the feed to mineral dressing plants are the mixture of ore minerals having different physicochemical properties among others, especially susceptibility on crumbling. During exploitation of material and their preparation to communition the big number of narrow classes comes into being and they have different properties. The determination of common communition laws of multicomponent (on account of size and mineralogy) materials leads to the estimation of mutual influence of narrow classes and their rates, taking into account their endurance and mineral density, on general ratios and their simultaneous crumbling.If we try to accept the grain membership to the certain component as the differing feature, we can write the balance equation as: ( ) ( ) S= = k i i i g x p f x1where: fi – density functions of one type distribution and of different statistical moments (characterising the homogeneous materials grinding), pi – “stirring” proportions of each components, S== k i i p 1 1 . From the point of verification view of detailed versions of this equation the inverse operation should be done: in the base of the components’ mixture grinding results and the results of components grinding the legitimacy of equation should be checked.The using of finished distribution mixtures’ theories to the grinding process analysis allows, first of all, to verify the assumption of grinding independence of individual feed components. Talking more generally it would lead to the comparison of grain size distributions, obtained by individual components grinding from the defined in the mixture distributions theory calculations. One of experimental and calculation results for artificial mixtures of galena and dolomite is presented on figure below (df means distribution function)"

Jan 1, 2003

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By Jacek Kolacz

"Comex has carried out an extensive research work related to optimising sensor based sorting systems. The main target was to achieve efficient separation and maintain high capacity of the process. Eventually, the operating cost of the sorting process was investigated in terms of potential industrial applications and possible replacement of the existing traditional processing equipment. The study included an influence of the following factors on the separation efficiency: capacity, particle size and distribution, particle shape, material properties like colour, density and composition, as well as percentage of the rejected fraction. The above factors were also considered in the calculation models for the operating cost of the sorting process. In addition, other elements were considered like compressed air cost, cost of energy, labour cost, and necessary service and maintenance cost. All these elements were implemented into the calculation model allowing quick and effective evaluation of the major parameters for sorting applications. Finally, the study was carried out for two popular sorting principles: visible light sorting utilising differences in color, texture and shape and X-ray sorting using differences in density and chemical composition. GENERAL INFORMATION ABOUT SORTING POSSIBILITIES Application of the sensor based sorting systems, without any doubt, brings a lot of possible advantages in many mineral operations. The main advantage of the new system is related to its universality and at the same time very sophisticated image processing functions, which can be carried out in the same processing unit (Kolacz, 2014). Figure 1 shows the CXR-1000 system from Comex with 1 m belt width, in the configuration where many different analysed parameters can be used to provide particle separation. The image analysis system includes a camera installed either over the transport belt conveyor or at its discharge end. The system includes the X-ray attenuation analysis realized by the XRT system in the central part of the conveyor belt. The sorting system can be used with both optical and XRT analysis or separately depending on an application."

Jan 1, 2018

By R. K. Logric

Bor flotation tailings are very interesting from two reasons: first, is having due value presently, and second represent serious pollutant into this region of Balkan. This paper is only one small part of investigation about processing of valuable minerals from tailings, and desulphurization of this biggest pollutant in the same time, by refloating. The main objective of this work is to pay attention on this problem for resolve greatest environ-mental problem of Serbia and Balkan in the nearly future. Bor is potential regional risk spot, since that failure of its tailings dams would release high amounts of toxic materials that would reach the Danube River. The basic goal of this experimental investigation was finding some possibility for flotation tailings treatment by classical froth flotation. In order was obtained material effect through copper recovery, and environmental protection by moving the rest of reprocessing into the safe place. The work present obtained results of laboratory tests in two laboratories: laboratory of mineral and recycling technology at the faculty in Bor, and laboratory of department of mineral processing of ITNMS in Belgrade.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By Mohana Rao Andavarapu

Sandur Schist Belt of Karnataka Craton constitutes a hub of iron ore mining activity. The iron ore deposits of the region are closely associated with Banded Hematite Quartzite (BHQ), Shale, phyllites, & Graywackes. The gradual depletion of high-grade iron ores due to extensive utilization has necessitated the exploitation of low-grade iron ore including BHQ, which are available abundantly in different parts of India. In the present investigation, BHQ samples from Kammaturu mines of Sandur schist belt was studied to assess the possibility of upgrading the iron content to the maximum possible extent, so that it may find the better use in iron and steel industries. The sample collected from the study area analyzing 39.76% Fe, 39.8% SiO2, 0.66% Al2O3, and 1.92% LOI was subjected to beneficiation studies. The mineralogical studies reveals that the samples are predominately consists of hematite as an iron mineral and quartz as gangue mineral. Liberation studies and chemical analysis were carried out prior to the beneficiation process, which is flotation. Cationic Reverse flotation studies were carried out and discussed by varying different process variables such as feed size, depressant, collector cum frother dosage & pH. The results obtained are encouraging with an appreciable improvement in the iron content up to 62.8% Fe with Fe recovery of 50.43%. The concentrate obtained from the flotation can be used for pellet making process.

Sep 1, 2012

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012