Search Documents

By V. M. Hamza

Analysis of ground and airborne radiometric measurements in the Saquarema region (Rio de Janeiro) provides new insights into the breakdown and transport of mineral aggregates containing monazites, under sub-tropical weathering conditions. The breakdown process, accompanied by loss of low-density clay fractions in weathered materials is considered responsible for the observed patterns in relative enrichment of thorium and uranium along the migration paths of radionuclides. The characteristic features of these patterns provide clues as to the time and distance scales associated with processes of weathering and erosion. It is also possible to determine approximate locations of concentrations of accessory minerals. In this context, we advance the hypothesis that large under-water monazite deposits may be present along the offshore sand banks, in the coastal region of the state of Rio de Janeiro.

Sep 14, 2011

By Justin C. I. Baulch

In October 2004 Placer Dome entered into an exploration farm-in agreement with Nautilus Minerals, to explore for Submarine Massive Sulphide (SMS) deposits on Nautilus? PNG exploration tenements. Placer/Nautilus currently holds approximately 15,000 km2 of tenements in PNG waters, either granted or under application, covering all reported seafloor hydrothermal vent occurrences.

Jan 1, 2005

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Nobuyuki Okamoto, Bhaskar Rao

For a period of twenty years - from 1985 to 2005 - the Japan Oil, Gas and Metals National Corporation (JOGMEC) and Pacific Islands Applied Geoscience Commission (SOPAC) have jointly conducted surveys of deep-sea mineral resources in the EEZs of SOPAC’s twelve member countries. The overall Programme has obtained excellent results and has identified numerous sites with potential marine mineral resources of manganese nodules, cobalt-rich manganese crusts, and polymetalic massive sulphides. The survey cruises have identified numerous sites with potential marine mineral resources such as: manganese nodules in the Cook Islands; cobaltrich manganese crusts in the Marshall Islands, FSM, and Kiribati; and polymetalic massive sulphides in Fiji. Based on collected samples and acoustic data, inferred resources for manganese nodule, cobalt-rich manganese crusts, and polymetalic massive sulphides, have all been estimated to be about- 200 million tons in the central Cook waters- 200 million tons in the three seamount selected Marshall waters- and 500 thousands tons around the triple junction of the North Fiji Basin.

Oct 15, 2007

By James C. Barker

Concern over the availability of domestic critical and strategic mineral supplies has led the Bureau of Mines to evaluate the reserve development potential of alternative sources in Alaska. Near the village of Platinum, on the southwest Alaska coast, the Red Mountain concentrically zoned ultramafic complex is a source of onshore alluvial placers containing platinum-group-metals (PGM). It has long been suggested that valuable placers may also underlie the shallow coastal waters of the Bering Sea. A direct correlation of placer PGM and chromium to ultramafic rocks in the area was studied by the Bureau and the extent of the complex was mapped. Magnetometer and gravity data and geological studies suggest the complex is a large lensoidal body trending several kilometers offshore to the southwest with a probable steep southeasterly dip. Multiple Pleistocene glaciations and marine transgressions have eroded the western and southwestern portion of the complex. Sediments containing PGM, chromium, and associated gold (largely derived from glacial till) have been transported northward along the advancing coastline by littoral currents. Beyond the breaker zone, these sediments are generally buried by recently winnowed sand and gravel transported by strong longshore tidal currents. There is also evidence that paleoplacer channels underlie the marine sediments.

Jan 1, 1986

By D. S. Cronan

Mineral exploration problems in the S.W. Pacific are not unique to that region, but a combination of favourable circumstances render it an ideal area to attempt to solve such problems. The land area of the S.W. Pacific island nations is only a fraction of the total sea area they can claim under current International Law. Hence, they have a great need to explore and evaluate their offshore areas. For the past ten years the focus of this work has been CCOP/SOPAC which has individually and jointly with other groups initiated and maintained far reaching marine mineral exploration programmes. In association with CCOP/SOPAC the writer has obtained and analysed approximately 650 sediment samples from the S.W. Pacific region for seventeen elements. Multivariate statistical techniques have been applied to the data set. The aim has been to identify chemically anomalous sediments reflecting either sea floor mineralisation and/or mineralisation on adjacent land areas.

Jan 1, 1985

By G. McMurray

The release by the U.S. Department of the Interior (DOI) of a Draft Environmental Impact Statement (DEIS) for the leasing of polymetallic sulfide minerals on the Gorda Ridge in December 1983 resulted in strong negative public reactions. The fundamental issues affecting federal-state relations included the amount of state involvement in the planning process and the continuing question of consistency (sensu Coastal Zone Management Act). The specific issues raised included the authority of DOI to lease nonenergy minerals offshore, the economic and strategic rationale for the proposed lease, and the adequacy of the DEIS. The questions of DEIS adequacy arose in three major areas: the lack of evidence for the existence of polymetallic sulfides on the Gorda Ridge, the lack of sufficient baseline data, and the lack of a mining scenario from which to assess potential impacts. The joint Federal-State Technical Task Force was formed in February, 1984 as part of an initial agreement between the State of Oregon and the Department of the Interior to work cooperatively. Other points in the agreement were (1) a reduction of any future proposed lease area from 40 million acres to no more than 4 million acres; (2) indefinite postponement of the lease sale; (3) deletion of the nearshore portion of the possible lease area covering the physical continental shelf and slope; (4) a commitment of a "tiered" EIS process; and (5) sharing of non-proprietary data with the public.

Jan 1, 1985

By Andrew E. Grosz

The United States is dependent on foreign imports for about 80 percent of its ilmenite, about 60 percent of its rutile, and virtually all of its monazite. Nearshore marine sand deposits and beach-complex sediments in the southeastern United States are important domestic sources of ilmenite, leucoxene, rutile, zircon, monazite, and a number of other less well known economic heavy-mineral (HM) species. Because global onshore reserves of placer titanium minerals may fall short of demand in as few as 20 years, offshore research in HM placers will become more important. The Atlantic Continental Shelf (ACS) defined by the shoreline and the 200-m isobath varies in width for the modern U.S. coastline from a fraction of a kilometer to about 150 km offshore of Cape Cod, Mass., and includes an area of about 3.91 x 105 km2. It probably contains 3-7 x 1011 m3 of sand and gravel which may locally contain commercially exploitable placer HM deposits.

Jan 1, 1986

By Timothy F. McConachy

Hydrothermal fluids emanating from the seafloor rise as buoyant plumes, entraining ambient bottom sea water on the way up, until they reach density equilibrium and spread laterally in a direction that is governed by near-bottom currents. Plumes provide targets for focussing exploration for seafloor polymetallic sulfide deposits associated with active hydrothermal vents because their lateral and vertical extent is commonly orders of magnitude larger than the vent field from which they originate. Black smokers can inject on the order of 10,000 µg of particles per liter into a sea water column that normally contains only about 10 µg of particles per liter. The resulting plume should be characterized by increased particulate concentration with respect to background sea water and, therefore, provide a measurable gradient towards the source of venting. By utilizing the ability of particles to scatter light, we employed a real¬time, acoustically telemetered, nephelometer to measure this gradient, and mapped the size, shape and particle concentration of plumes at an active spreading center on the Southern Explorer Ridge at lat 49°45.6'N and long 130°16.2'W. Isopach and particle concentration data indicate the presence of two separate but overlapping plumes. The first is associated with a known vent field called Magic Mountain; the second with a new field called AGOR 171, 1.2

Jan 1, 1986

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By Bonnie A. McGregor

The U. S. Geological Survey in cooperation with the Institute of Oceanographic Sciences (IOS), U.K., conducted a sidescan sonar survey of the U. S. Exclusive Economic Zone in the Gulf of Mexico from August 7 to October 22, 1985. A reconnaissance-scale view of 120,000 square nautical miles of sea floor seaward of the shelf-edge was obtained by using the GLORIA (Geologic Long-Range Inclined Asdic) sidescan sonar system. After these data were merged with GLORIA data from an earlier survey (1982) of the northwestern Gulf, a preliminary mosaic was constructed at a scale of 1:375,000. From this mosaic, we can identify morphologic features and interpret sea-floor processes. The extensive deformation of the continental slope seaward of Texas and Louisiana by salt tectonics has resulted in a complex pattern of basins and salt dome highs. One continuous meandering channel was identified in this portion of the Gulf, extending from the shelf edge to the Sigsbee Abyssal Plain. Bottom currents have reworked the sediments in this channel's levees seaward of the Sigsbee Escarpment, the seaward edge of the salt front, suggesting that this channel may no longer be actively transporting sediment. Talus appears to lie along the base of the Sigsbee Escarpment, suggesting that erosion and deposition is occur- ring along this front. Three other discontinuous channel systems can be identified on the mosaic and appear to have contributed sediments to the deep Gulf.

Jan 1, 1986

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45' and 41°05'N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01'N latitude are part of a chimneylike vent structure with a

Jan 1, 1988

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By Robert M. Owen

Geochemical exploration for marine placers involves the acquisition, processing, and interpretation of geochemical data. Recent technological advances such as in-situ analysis systems and microcomputers have greatly improved our ability to acquire and process data, but their full benefits cannot be realized until we also develop improved methods for reducing and interpreting large amounts of raw geochemical data. Toward this end, our research has sought to identify existing and/or develop new geostatistical techniques for use in marine placer exploration. Each technique has been tested by evaluating its performance in the analysis of existing data sets. The data sets typically include the results of chemical analyses of suites of sediment samples collected from areas of known or suspected platinum and gold placers along the Bering Sea coast of Alaska. Results to date indicate that three geostatistical methods (subpopulation partitioning analysis, comparative factor analysis, and end-member compositional factor analysis) are useful in identifying elemental groups which can serve as "pathfinders" in the search for marine placers, and are also helpful in discerning the generic geochemical basis under lying observed statistical correlations between pathfinder elements and placer minerals. Existing methods of modelling sediment dispersal patterns have been examined with a view toward adapting them to the specific problem of understanding placer formation in

Jan 1, 1986

By J. R. Woolsey

Research grants of The Marine Minerals Technology Center (MMTC) are directed toward development of the technology 'for exploration, mining, and processing of non-fuel mineral resources within the U.S. Exclusive Economic Zone. FY 1989-90 research grants are as follows: - Seafloor Gamma Measurement Data Collection System. - Free-Fall Seafloor Hard Substrate Corer. - Microtopography of Manganese Crust Deposits. - Cobalt Crust Continuum on Seamounts, EEZ, Hawaii. - Economics of Marine Polymetallic Sulfide Resources. - Graphite Furnace Atomic Absorption Spectrometer. - Depositional Models for Aggregate and Heavy Mineral Exploration. - Sand Resources of Heald and Sabine Banks, Texas. - Sources, Geometries, and Compositions of Heavy Mineral Placers. - Geostatistical Methods for Marine Placer Exploration. - Computer Aided Design for Communication and Strength Umbilicals.

Jan 1, 1989

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By Charles L. Morgan

For the past twenty years or so the oceans of the world have been transformed in the minds of most Americans from the ultimate and nearly infinite receptacles for sewage and other wastes to an almost sacrosanct and threatened last refuge of Mother Nature from man on Earth. While this general movement has helped somewhat to moderate the flows of pollutants into the oceans, it has had severe and sometimes devastating impacts upon various attempts to develop seabed mineral resources. Marine mining proposals have been easy targets for attack. In most cases, they have short or no histories and involve prototype or first-generation methods. They commonly lack major financial backing, and do not command significant public support. Their constituents are limited. Opposition movements to such proposals have been able to evoke strong support by appealing to this "last refuge" image and depicting mining operations as the final assault. In mounting these public appeals, the movements obtain visibility and support. Because of the small and sometimes tentative status of the constituencies which support particular proposal s, the potential liabilities for opposition movements are minimal.

Jan 1, 1989

By David A. Larson

The future exploitation of crust deposits will require a dependable characterization system. The U.S. Department of the Interior, Bureau of Mines (Bureau) initiated research to develop a new sampling dredge by conducting a series of cutting and physical property tests on previously collected cobalt-rich manganese crust and substrate samples. Using the engineering parameters derived from these tests, a large, heavy dredge was designed and tested. This heavy dredge was capable of fragmenting and collecting in situ crust, but it created handling problems for the research vessel, thus an aggressive cutting, light-weight dredge was conceived and fabricated. The light-weight dredge is capable of fragmenting and collecting crust and some talus. This dredge can be used on flat or rough seabed terrains. It can be easily retrieved from hang ups and reset to sample again.

Jan 1, 1991

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985