Search Documents

By Claudia Gasparrini

"Silver occurs in about 200 minerals in variable amount s. Silver ores usually have 5 or 6 and in some instances as many as 10 species of silver minerals. All these minerals may have different flotation and leaching properties and should be correctly identified for successful recoveries. Grain size and host minerals which are critical in gold recovery, are not always as important for silver minerals.IntroductionMineralogical factors affecting the metallurgy of silver are , as for other metals: (i) the silver-bearing mineral s ; (ii) their grain size, and when dealing with very fine sizes; (iii) their host minerals; and (iv) the association they form with the silver-bearing minerals. Of these, the silver-bearing minerals are more often the cause of problems during recovery as opposed to gold whose metallurgy is generally more affected by grain size and host minerals. The problems derive mainly from the complexity of the silver mineralogy: over 200 minerals exist bearing the element in major, minor and variable amounts.As a member of group I-B of the periodic table, silver forms extensive so lid solutions with the other two elements in the same group , copper and gold. It combines with sulphur, tellurium and selenium in covalent bonds and with chlorine, bromine and iodine in ionic bonds. Where the fluid composition, temperature and pressure during crystallization allow it, silver also combines with arsenic, antimony, lead, bismuth, tin, mercury, indium, thallium, and germanium in many instances as a minor element in sulphide , sulphosalt and native element minerals. Cations which silver replaces to a lesser extent than copper and gold are iron, manganese, zinc and probably nickel and cobalt."

Jan 1, 1984

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

New Millennium Capital Corp. shall not be liable or responsible for any claim or damage, direct or indirect, special or consequential, incurred by the user arising out of the interpretation, reliance upon or other use of the information. Users should not rely on information for any purpose other than for gaining general knowledge of New Millennium Capital Corp. Although New Millennium Capital Corp. believes that its expectations reflected in these forward-looking statements are reasonable, such statements involve risks and uncertainties and no assurance can be given that actual results will be consistent with these forward-looking statements.

May 1, 2011

By A. Liard, H. Sommelet, G. Sauriol

"Description des études qui ant conduit à la conception spécifique du système de drainage de la mine à ciel ouvert. Les approches différentes sont examinées ainsi que la valeur du système recommande.IntroductionLa Division Mines Gaspé de Mines Noranda Ltée exploite un gisement de cuivre par mine souterraine et mine à ciel ouvert à Murdochville, Québec. L'exploitation par mine aciel ouvert a commencé en 1965 avec une operation à flanc de montagne. Elle se poursuit actuellement sous Ie niveau de la vallée dans une fosse dont Ie diamètre est de I'ordre de 800 m (2,600 pi), et la profondeur de 150 m (500 pi) sou s Ie fond de la vallee. Elle doit atteindre une profondeur de 360 m (l, 180 pi) sous Ie fond de la vallee , avec des murs hauts de 360 à 490 m et des pentes moyenne de 44°. Le rythrne d'extraction est actuellement de 85,000 tonnes par jour.Dans Ie cadre des etudes entreprises par les Services Techniques de la Division Mines Gaspé, la compagnie Géomines Ltée a été consultée pour étudier les conditions hydrogéologiques et hydrologiques locales et participer a la conception d'un système de drainage superficiel et souterr ain. Un tel systerne de drainage visait: a éviter les importantes venues d'eau qu i affectent I'exploitation en periode de crue; amaintenir les pressions hydrostatiques au sein des parois de la fosse dans les limites imposees par les etudes de stabilite des pentes réalisees par la Mine.Les principales étapes de cette etude ont porté sur: la collecte et la compilation des données sur la géologie, l'hydrologie et l'hydrogeologie du site; . la détermination des caractéristiques hydrauliques du milieu rocheux à partir d'études structurales et de test s de perméabilité;"

Jan 1, 1981

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By M. A. Upham

"Prairie Evaporites of the Province of Saskatchewan in a deep oil-well hole. Exploitation started in 1950 under a shroud of doubt that this huge reserve could be mined. It was fraught with almost insurmountable physical problems in penetrating the Prairie Evaporites. After 12 years of experimentation and development of new shaft-sinking methods, mining equipment and processes to treat the high-grade potash ore (sylvanite), a new era of high-risk resource development dawned in Saskatchewan.The development of 10 new mines opened up the largest known mineable potash reserves in the world and Canada became the second largest. producer of potash to supply domestic (U.S.A. and Canada) and overseas markets. A monumental program in marketing-devising new transportation systems and strategically locating warehouses-was developed in order to expeditiously service domestic and overseas customers. The year 1969/70 started a period of overcapacity and the problem of prorationing. As the market strengthened in 1974, the Saskatchewan Government applied the reserve tax to the industry. Then, they announced the setting up of a Crown corporation to acquire ownership by purchase of up to fifty per cent of the industry. During this time, potash was discovered in New Brunswick within 50 to 60 miles of a seaport, where two deposits have been explored by the same pioneers who started the potash development in Saskatchewan.With this background, the paper will examine various elements of the economics and marketing of Canadian potash."

Jan 1, 1980

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By R. Mariano

"The ability to optimise a concentrator from mill feed to final products requires a process simulator that integrates comminution, classification and separation stages. A key part of any such integrated process simulator is the inclusion of a model of mineral liberation in comminution to predict the particle composition distribution of the comminution products. This need was recognised by Gaudin (1939) who proposed a model of liberation based on the cubic fracture of a mineral texture composed of cubic grains of two minerals.This paper describes the development of a texture-based model of mineral liberation that builds on the method proposed by Gaudin. The approach described here, termed the JK-Gaudin Random Liberation model (JK-GRLM) uses as its basis the measured, volumetric mineral texture data that can be quantified for a given ore using X-ray micro-tomography. The textural data required as inputs for the JK-GRLM include the mineral grain size distribution. While the Gaudin model (in common with other existing liberation models) is a two-mineral (or two-phase) system, the JK-GRLM extends the approach to multimineral systems of up to 15 individual minerals, making it more widely applicable.An example of the application of the JK-GRLM to a base metal sulphide ore is provided. In the example the JK-GRLM is used to simulate the breakage of the measured ore texture and the particle composition distributions of the simulated progeny particles are compared to the measured particle composition distributions of ore that has been physically broken.The ability to calibrate this mineral liberation model with measured ore texture will allow it to be applied in greenfield situations where geometallurgical programs measure texture and in brownfield applications as a key part of integrated process simulations. The development of this model enhances our ability to simulate mineral processing operations as an integrated system."

Jan 1, 2016

By Doug Ashbury

Diamond Miners? Challenges ? Remote ? 300 kilometres from Yellowknife ? Sub-Arctic conditions ? permafrost, climate ? No power ? No all-weather roads ? Ore bodies difficult to find ? Caribou, fish of special concern ? Communities with low education, little experience, but high expectations ? Major investment required ? Diavik C$1.3 billion

Apr 1, 2005

By A. Sutherland Brown

"The ProblemMany science activities receive substantial funding from governments without much direct economic benefit accruing to state or individuals. In contrast, the search for knowledge has never been an acceptable so le justification of geoscience activity, perhaps because of its utility right from its inception. William Smith's geological activities were embraced because of their usefulness in building canals. Utility has been expected ever since.For decades it has been accepted at senior level s of government, without much understanding of the process, that geological surveys are necessary as a basis of resource evaluation and utilization. Recently, government treasury board s, staffed with economist s, have questioned these near axioms and in many cases the budget s of geological surveys have reflected their stone y-eyed appraisal s. Are government surveys necessary? Can their functions be reduced? Can some or all of their functions be privatized?Government geologists have been muted in trumpeting their successes outside their own ranks. Companies have been reluctant to give specific public feedback on the work of government surveys that have truly aided or guided them toward discovery. Lack of acknowledged linkages between survey work and discovery has dogged survey managers in budget reviews. Impoverished surveys cannot perform adequately so the circle is completed and the doubters' prophecy fulfilled. This is the genera l problem; British Columbia is the archetypical province."

Jan 1, 1986

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By G. Pouskouleli, T. A. Wheat

"The role and benefits of using statistical methodology in the development and optimization of materials and processes is examined. It is shown that considerable benefits accrue from the use of an appropriate design in which a number of factors (process parameters) are varied simultaneously while the system response such as percent recovery, degree of separation, purity, etc. is monitored and ultimately optimized.Compared with the commonly encountered one-factor-at-a time approach, this schema exploits reduced experimentation (thereby requiring reduced resources [staff, time, dollars, etc.]) yet yields quantitative information on the significance of each factor and their combinations on the measured response."

Jan 1, 1992

By J. Bigu, M. G. Grenier

"Dust size distribution and aerosol size distribution measurements have been carried out in several Canadian underground uranium mines. In addition, dust samples have been analyzed for long-lived radioactive products of the U-238 and Th-232 natural decay chains using ex-spectroscopy and -y-spectroscopy techniques.From the data collected one may summarize: (a) most airborne particulates are of size below I u-m and 50% by mass are found above 1 u-m; (b) dust clouds are bimodal; (c) preferential deposition of radon (thoron) daughters takes place on airborne particulates in the sub -micron range at about 0.1 u-m; (d) deposition of radon (thoron) daughters is proportional to particle surface area; and (e) ex-spectroscopy and -y-spectroscopy of dust samples reveals the presence of U-238, Ra-226 and some of their short-lived and long-lived decay products.IntroductionExtended inhalation of airborne radioisotopes poses a potential health problem to occupational workers. Because of this, monitoring of radiation and dust levels for dose exposure calculation purposes is not only recommended but in most cases mandatory.CANMET (Energy, Mines a nd Resources Canada) has long since been engaged in a comprehensive monitoring program aimed at determining dust concentrations in the respirable size range, aerosol concentration in the sub-micron range, and in the radioactivity associated with these particulates in underground uranium mines. Measurements have been carried-out with gravimetric dust samplers, dust size selectors (including a horizontal elutriator , a fineparticle spectrometer and Nuclepore* filters of different pore sizes) and a condensation nucleus counter(1 – 6). Inactive and active working sites have been monitored according to some typical mining operations. A summary of these data has been given elsewhere(3- 5)."

Jan 1, 1984

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993