Search Documents

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By P. Belley

Prior to 2006, the filtration unit for leached sludge treatment (filter press) permitted the filtration, washing and drying of cake to 17% (w/w) moisture. That year saw moisture content abruptly increase to 20% (w/w), drastically changing the rheological properties of the cake. The cake became sticky and agglomerated. This led to major disruptions of operations and plant capacity (cake release and cake conveyor problems, complicating the subsequent steps of the process). The conditions for the filtration, washing and drying, were simulated to ease cake unloading without aggravating dust emissions (moisture about 17% (w/w)). All of the laboratory tests yielded a moisture content above 17% (w/w). Therefore, we concluded that the moisture problems were not due to a recipe change in primary material, but to an operational problem in the filter press. Through the laboratory results, the filter press operating conditions (washing ratio, drying pressure and drying time) were optimized to enable a reduction in cake moisture to 17% (w/w).

Jan 1, 2007

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By J. Mcdvcka

Sustainable development has become a driving imperative for the resource industry as it is for the rest of the global business world. Being unsustainable is a risk no business can afford. Yet implementation of sustainable development practices beyond satisfaction of compulsory reporting is still sporadic. The current standard approaches to problem analysis and decision making are too narrow to capture the complexity of the issues at stake. Hence it is necessary to develop innovation in thinking and in doing. Those who search for ways to implement sustainable development use concepts such as Whole Systems Thinking and Eco-efficiency as well as tools like Life Cycle Analysis. Others develop their own instruments. In their effort to innovate they face both resistance and support within their organisation as well as within the industry or the wider context. This paper explores the factors that support, hinder and shape the sustainable development drive of the industry and proposes a comprehensive decision-making framework that links the goal of sustainability with the tools of sustainable development. This exploration is illustrated by a case study used in a doctoral research conducted on an engineering firm providing services to our industry.

Jan 1, 2007

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By G. M. Behrend

"AbstractMeasurement and control systems in minerals processing plants are usually well thought out and designed. The criteria and design parameters have been interpreted correctly.However, these systems often fail to perform satisfactorily or break down altogether as a result of in-plant conditions which are unpredictable and over which the instrument systems designer has no direct control. The foresight necessary to anticipate the problems and allow for them in the systems design can only be generated by experience.This paper lists the most common of these problems and offers practical methods for their solution. It then follows with an analysis of instrument installation practices and comments on special points that need watching.Finally, instrument maintenance is discussed with a view to achieving good maintenance at the best possible economy.Good MeasurementGeneralTHE MINES and mineral processing plants of the nineteen seventies, after decades of sensible caution, have now committed themselves to extensive automatic control. X-ray analyzers are freely specified. Sample acquisition systems are efficient and automated, computers are reliable and relatively cheap, and computer control systems in conjunction with the new analyzers are operating in a good many plants and are proving to be profitable.The sight of shift foremen and floor operators assembled in front of a TV-tube and taking a computer data display as gospel truth is quite common now, and yet was quite unthinkable only ten years ago."

Jan 1, 1977

By M. Côté, H. Pépin, Y. Richer, C. Gingras

Rolls-Royce Canada has been nominated as a Rolls-Royce Center of Excellence for repair of fan blades in 2003. One of the challenges of the Rolls-Royce Canada Component Repair Center of Excellence team is to reduce cost and time of inspection while ensuring trace ability and quality of the inspection performed on the fan blades. In the context of the dimensional control process optimization, and following the positive conclusions of initial trials carried out in 2003, the technical authorities at RRC have selected the SPG data 3D(TM) technology as a development base for dimensional control programs. The main goal of this development initiative is to develop and support an inspection system to perform the dimensional control and inspection of different components at the Montreal Fan Blade Repair Center of Excellence. The final objective of the program is to build a server platform capable to support different inspection sites within the Montreal facility for the future. This paper presents the certification process of the technology according to the VDI-VDE 2633 certification standards and some results of the fan blade inspection program of the BR 710, BR 715 and TAY according to the JES 195 engineering standards specification.

Jan 1, 2006

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By D. W. R. Haysom

"I AM CONSCIOUS of the honour you pay me by having invited me to address you on the subject of the Rehabilitation of the Sydney Steel Corporation. The true architect of the revival and rehabilitation is Robert Burns Cameron. Because of the numerous myths which have grown up around what seems to be the miracle of the revival of the Sydney Steelworks, I propose to go back to the time when they came under the full control of the Province, on the 1st of January, 1968. Late in 1967, the decision was taken by Premier G. I. Smith to keep the Steel Plant running for at least another year, in an endeavour to see whether the enormous losses being sustained by Dosco could be reduced to a level which would permit their continuing operation. When that decision was taken, Dosco was to continue management until the 30th of April, 1968, and in the intervening period, the Provincial Government would seek management of the right calibre to ensure that an objective view of the Steelworks operations could be secured. By a combination of circumstances which can only be described as most felicitous, the man selected for the task was R. B. Cameron. He very quickly determined that to permit Dosco to continue management of the Steelworks until April 30 could only result in heavy losses to the Province and a consequent deterioration in the already critical financial position and a declining morale of the worke"

Jan 1, 1972

?Bank Lending to the Mining Sector affected by 2 broad factors since Mid 2008: 1. Economic Downturn (?the Real Economy?) for mining companies directly reflected in lower metal prices (current and forecasted). In the case of gold companies, minimal effect. 2. Financial Crisis (?the Credit Crunch?) as it has affected the lending activities of those banks active in the mining sector.

May 1, 2009

By J. Contreras

In the period 2003-2004, the situation of the copper concentrate market was unfavourable for smelters and refineries, with low TC/RC values and euro-dollar parity affecting European companies negatively. Within this scenario, Atlantic Copper decided to develop a plan to increase its competitiveness and to improve its results in these market circumstances. The plan affected all departments in the Company and was based mainly on cost reduction in energy and manpower. A general analysis of the Complex's overall efficiency was carried out and, based on this analysis, two major Projects emerged, "Primavera" and "KF". Each Project consisted of smaller sub-projects which aimed at improving the areas which could perform better according to our general analysis. The paper describes how this entire project developed and the final results obtained by the Company.

Jan 1, 2007

By R. E. Evans

This paper contains an analysis of the geography and geology of the Black Lake area, Eastern Townships of Quebec, an outline of the work to be performed, an explanation of the design concept and how it was developed, and a discussion of the actual stripping operation, including details of the machinery being used, etc.

Jan 1, 1967