Search Documents

By A. Garnier, K. Tremblay-Bouliane, B. Gaillet, S. Moineau, D. Tremblay

"A heptapeptide library displayed on M13 bacteriophages (phages) was screened to identify peptide sequences able to selectively bind to gold, chalcopyrite, sphalerite, pyrite, and silica ores, and to evaluate phage potential as bioflotation reagents. Many peptide sequences were isolated through biopanning and differed from known sequences. Adsorption isotherms were determined and a receptor/ligand interaction model was identified and used to compare affinity of peptide sequences toward ores. Some phage sequences have slightly lower affinity to sphalerite than other sulphides. Adsorption was higher on sulphides than on silica. Induction time measurements suggested filamentous M13 phages lower hydrophobicity of the ore surface.RÉSUMÉ Une librairie d’heptapeptides présentés sur des bactériophages M13 (phages) a été criblée afin d’identifier les séquences peptidiques affinitaires à des minerais d’or, de chalcopyrite, de sphalérite, de pyrite et de silice et d’évaluer le potentiel de ces phages en tant que de bio-réactifs de flottation. De nombreuses séquences peptidiques ont été isolées par bio-criblage et différenciées d’autres séquences connues. Des isothermes d’adsorption ont été déterminées et un modèle d’interaction récepteur–ligand a été identifié et utilisé pour comparer l’affinité des séquences peptidiques par rapport aux minerais. Certaines séquences de phages possèdent une affinité légèrement inférieure pour la sphalérite comparativement aux autres sulfures. L’adsorption sur les sulfures était plus élevée que sur la silice. Des mesures de temps d’induction suggèrent que les phages filamenteux M13 diminuent l’hydrophobicité de la surface des minerais."

Jan 1, 2016

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006

By C. A. D' Odorico

The zinc pressure leaching (ZPL) plant at Teck Cominco&apos;s Trail Operations was started up in 1981 and represented the world&apos;s first commercialization of the technology. From the outset, the process was designed to operate using iron-rich Sullivan Mine zinc concentrate. When the Sullivan Mine reached the end of its life in 2002, the ZPL plant underwent a significant process change with the treatment of 100% Red Dog zinc concentrate. Through careful improvements to existing plant processes, controlled changes to plant operating parameters and a rapid adjustment to the modified process by operations personnel, the plant has been successfully converted to processing a feed of 100% Red Dog zinc concentrate. This paper discusses the challenges faced during the conversion and describes the modifications to plant operating procedures, as well as changes to plant processes.

Jan 1, 2004

By Anton Gronningsater

AT the present time we hear a great deal about organization of labour, collective bargaining, workmen&apos;s councils, and company unions; about C.1.0. with its principle of vertical unions and A.F.L., largely based on craft unions; and about provincial and federal laws for protection of labour&apos;s right to collective bargaining. What we perhaps hear too little about is corresponding organization of the employers, although it recently is mentioned more frequently. I will only mention W. H. Davis, Chairman of the United States War Labour Board, who has had and is having plenty of experience in this field and has also studied labour conditions in Europe-in Sweden for instance. He has repeatedly expressed the opinion that where employer-employee problems are involved, a thing badly needed in America is organization of employers as well as employees to get some order in the present chaos. With this I agree. I believe a strong organization on one side necessitates a correspondingly strong organization on the other side; that has at least been the experience in the industrialized countries in Europe. I happen to be fairly familiar with conditions in Norway, where they have struggled with these problems for fifty years, and a talk on the history, development, and present state of employer-employee relations in that country might perhaps be of interest as giving a general picture of the development of such relations in the northwestern European countries as a whole. The talk was originally given to the Fourth Year students in Mining and Metallurgy at the University of Toronto. I have changed it somewhat to fit a different audience, but I hope you will make allowances if you now and then are reminded of the school auditorium. I will try to be as objective and factual as possible, but it is probably unavoidable that some of what is said is coloured by personal opinion.

Jan 1, 1943

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By Mohamad Kharseh

There is general acceptance that climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, improving the performance of our existing energy systems and deploy more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing of heat energy in deep rock and sedimentary basins. This energy can be used to drive a power turbine to generate electricity. Traditionally, geothermal has been exploited in places with the plentiful hot water at relatively shallow depth. In the light of fact that ground temperature increases with the depth everywhere on the Earth, engineered geothermal systems (EGS) can be installed in any place to exploit the geothermal in generating energy. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to commerciality of EGS worldwide. In addition, there are technical problems associated with drilling big depth. In oil producing countries such problems can be addressed by utilizing whether active or abandoned oil or gas wells and, consequently, EGS can produce power at profit. The current study presents an analysis of a binary geothermal power generation system for commercial electricity generation in Qatar. For this purpose, two binary cycles are assumed the main difference between them is that the first one is air cooled while the other will be water cooled. The performance of the two cycles and the possibility of improvement has been shown. Economic analysis the power plant shows that the levelized costs of electricity is 3.6US¢/kWh and the pay-back time is less than 8 years.

Aug 1, 2013

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By J. Zhou1

"The extractive metallurgy of gold ores is largely driven by their grade and mineralogy. The concentration of gold in the crust is extremely low and highly variable, resulting ore variability in many gold and copper-gold deposits. More importantly, gold in an ore may occur in two or three forms (i.e. microscopic gold, submicroscopic gold and surface gold), making gold ore processing extremely challenging. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes. The objective of gold geometallurgy is to reduce and minimize the technical risk in project evaluation, plant design, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical and metallurgical testwork. Gold deportment study is a powerful tool in characterization of various gold ores. Effective and quantitative gold deportment results are critical and useful for predicting gold recovery and building geometallurgical models of gold ores. This paper provides an overview of geometallurgy fundamentals and applications in gold processing, with a focus being on the ore characterization and gold deportment study.INTRODUCTION Geometallurgy is an inter-disciplinary approach which links the geological, geochemical and mineralogical characteristics to the metallurgical performance of an orebody. Combined with mine planning, it has been used in scoping, prefeasibility and feasibility studies, process design and optimization of gold, copper-gold, copper-moly, nickel and iron projects among others (Williams & Richardson, 2004; Dobby, Bennett, Bulled, & Kosick, 2004; Bulled, 2007; Bulled, Leriche, Blake, Thompson, & Wilkie, 2009; Kormos, Sliwinski, Oliveira, & Hill, 2013; Muinonen, Sciortino, Korczak, & St-Jean, 2013; Leichliter & Larson, 2013; Leichliter, Jahoda, & Montoya, 2013; Hatton & Hatfield, 2013; Baumgartner et al., 2011, 2013; Hoal, Woodhead, & Smith, 2013; Zhou, 2013). The goal of a gold or copper-gold geometallurgical program is to characterize and understand the metallurgical variability of an orebody, such as comminution, gravity, flotation and cyanidation parameters and metal recoveries, and to build a geomet model which can be used to assist in mine planning and to predict the plant performance. In any geometallurgical program, representative sampling is the key to ensure the results of a geometallurgical study will reflect future performance once the plant is commissioned. Geometallurgy compliments, but does not replace, the traditional mineralogical and metallurgical approach during the development and operation of a gold or copper-gold project. Geometallurgy is a methodology for testwork design and a framework for mine planning. The first part of this paper provides an overview of geometallurgy fundamentals and application in gold ore processing."

Jan 1, 2017

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By A. Ghahreman, M. Oliazadeh

"Heap leaching is an attractive process for low grade deposits where the metal content of ore does not justify the high cost of milling and agitated leaching. In general, the heap leaching capital cost is low, construction is rapid, and production costs are low. The primary disadvantage of heap leaching is low recoveries (typically 65% of agitated leach recovery); thus, recovery improvements could convert more lower-grade deposits into minable reserves. This will also allow to process primary sulfide ores and result in a dramatic expansion of the technology, as ~80% of total ore types are sulfidic in nature. The old gold operations tailings are another massive source of low-grade gold material that can be retreated by the heap leach process. The major parameters affecting the recovery rates are ore characteristics (mineralogy, particles size of metal and host minerals, ore permeability), and operational conditions (segregation of ore, compaction, leach cycle time, lift height, and solution application rates). The design of a percolation leach process is based on a limited number of coarse ore bottle roll and/or column tests under ideal conditions. The economics of the projects and engineering design of the process facilities are developed based on the bench scale test work results and the application of the conventional engineering scale up factors. This paper will deal with the parameters affecting the HL efficiencies and focus on the potential improvement of gold heap leach recoveries. This would include design of heap leach operation and evaluation of processes such as fine crushing and bioleaching.INTRODUCTION Gold heap leaching is a hydrometallurgical process designed to treat amenable low-grade gold ores that contain typically 0.5 to 1.5 g/t gold (Marsden and House, 2006; Wong Wai Leong and Mujumdar, 2010). Ore is stacked by various types of equipment on an impermeable barrier, and a sodium cyanide solution is applied to the surface of the stacked ore. Gold, silver, and other metals contained in the ore are dissolved to various degrees by the cyanide application, as it percolates downward through the stack of the ore. The pregnant leach solution (PLS) is then collected at the bottom of the heap. The PLS is then sent to the gold recovery plant where the metals are extracted. The barren leach solution (BLS) is then reapplied to the top of the pad. Ore is placed on a pad or previously leached lift by various means, including ramp conveyor belts, radial-arm and self-leveling stackers, and trucks. Once trucks are used to construct the pads, the pad can be compacted and hence the pad should be graded and ripped or scarified (roughened up) with wheeled or tracked equipment to produce shallow cuts to increase surface area exposure to the leachate."

Jan 1, 2019

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By W. A. Jankola, M. T. Martin

"The world&apos;s first zinc pressure leaching plant at Cominco&apos;s Trail operations started production in 1981. Sullivan zinc concentrate is leached at the rate of 190 tpd in a four-compartment autoclave at elevated temperatures and oxygen pressures to produce a zinc sulphate solution and elemental sulphur. Zinc extraction exceeds 98% and sulphide to elemental sulphur conversion exceeds 95%.The sulphur is recovered from the discharged slurry in the underflow of a hydrocyclone, and is upgraded as a flotation concentrate. The concentrate is dewatered, melted and filtered to produce a polished sulphur product of better than 99% purity. An alternative sulphur recovery process employs an unique sulphur separation method that recovers over 90% of the sulphur in the molten state. The remaining sulphur is recovered by flotation following flash discharge of the slurry. The product slurry containing the zinc sulphate solution and the iron-lead residue joins the existing roast-leach zinc plant for purification and zinc electrowinning.IntroductionIn 1981, Cominco Ltd. commissioned the world&apos;s first commercial zinc pressure leaching plant at their Trail operations in British Columbia. As part of a $700 million modernization and expansion program for lead and zinc started in 1977, the company installed the first o f two autoclave trains.Prior to pressure leaching, zinc production was closely tied to acid and fertilizer production. Sulphur dioxide produced from roasting the concentrates had to be converted to sulphuric acid. Thus, any expansion of zinc operations with the roast-leach technology would have required extensive modifications to the acid and fertilizer plants as well as to the roasters. Zinc pressure leaching, on the other hand, offered a one-step dissolution of zinc from the concentrates with high extraction, and production of elemental sulphur. The associated dust and sulphur dioxide generated in the roasting process are both eliminated from the working environment of the pressure leach facility. The flexibility allowed by producing elemental sulphur, and the opportunity to break the sulphuric acid link for about 25 per cent of the targeted 272,000 tonnes per year zinc production was very appealing. The process was successfully demonstrated at a pilot plant in 1977(1-6)."

Jan 1, 1985

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its &apos;primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40&apos;s. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956