Search Documents

By J. De Geoffroy, T. K. Wignall

The paper describes a statistical method based on regression and classification analysis which is designed to assist exploration management in the selection of prospecting areas and drilling targets in regional programs. The classification is based on three criteria which are formulated from sets of relevant geological, geophysical and geochemical factors: (a) regression estimates of expected ore values, (b) Bayesian probabilities of success and (c) expected utility payoffs. The advantages of the method are: (a) rational and unbiased ratings for areas or targets in a manner consistent with management's goals; (b) calculation of probabilities of success and confidence intervals for the ratings, and (c) rapid and accurate handling of a large amount of data by computer programs.

Jan 1, 1970

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By K. G. Davies, M. J. Royea

"A major program of pillar recovery at the Sullivan mine has been assisted for the past several years by a concerted series of rock mechanics investigations. The object of these investigations is to measure the parameters of rock behaviour which influence pillar mining. This quantitative information is then used in the design of mining methods appropriate for various conditions.Instrumentation to measure absolute rock stress, changes in rock stress and the gross deformation of rock masses has been developed. Various instruments are described, as are instrument evaluation procedures and typical test results. The data from underground measurement projects have been used to modify pillar extraction sequences along re-treat fronts. Rock mechanics information from individual pillars has been incorporated into the design of mining methods to suit particular circumstances."

Jan 1, 1968

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By J. G. Peacey

"Canada has a special place in non-ferrous pyrometallurgy because it is the only country in the western world that is a significant producer of all the major non-ferrous metals; aluminum, copper, lead, magnesium, nickel and zinc. This large non-ferrous pyrometallurgy industry has developed because of Canada's abundant mineral wealth and energy resources. Table I summarizes the number of primary non-ferrous production facilities in Canada and their share of western world production.Production of non-ferrous metals is a mature, capital intensive business and its basic processes have been in use for many years. Nevertheless, these processes have continued to evolve in response to changing needs and external pressures; such as the energy crisis of the early seventies; historically low metal prices in the early eighties and the continuing pressure to reduce plant emissions and improve in-plant working conditions. Canada's major metallurgical companies: Alcan, Cominco, Falconbridge, Inco and Noranda have played a leading role in pioneering new process technology and continue to meet the difficult challenge of keeping their operations competitive in the global metals market. This paper will try to give an overview of the major developments in non-ferrous pyrometallurgy, largely from the Noranda and Canadian perspectives, highlighting the current status of process technology and possible future directions.AluminumCanada has the world's second largest aluminum smelting industry and its capacity has expanded rapidly in recent years with the completion of several large projects in Quebec. The location and capacity of the Canadian aluminum smelters are given in Table 2. All these plants use the Hall-Heroult process, that was invented over a century ago but over the last twenty years considerable improvements have been made to increase productivity, reduce power requirements and emissions.The developments in aluminum cell technology can be illustrated by the experience at Noranda Aluminum. In 1971, Noranda Aluminum started its first pot line using Kaiser's P69 prebake cell, which was considered, at that time, the best available technology. The P69 cell was designed primarily for high productivity, operating at 150 000 amps and high current density to produce just over tonne Al per cell-day. The P69 cell is a simple design, typically operating at about 88070 current efficiency and 15 800 kWh/tonne Al. When Noranda Aluminum decided to expand in 1980, the Alcoa 697 cell was selected as it then represented the most proven, stateof- the-art technology. This cell is similar to that installed at Alcan's new Grande Baie and Laterriere smelters and is designed to operate at 180000 amps and 93070 current efficiency, producing about 25070 more aluminum per pot-day than the P69 cell using about 15070 less power. The 697 cell has a much more sophisticated cell design, with very good balancing of the magnetic field giving a flat metal pad and allowing efficient operation at the higher amperage. Alumina is fed via point feeders that provide an almost continuous feed allowing close control of the alumina level in the bath and the use of low-ratio bath composition, giving much higher current efficiencies."

Jan 1, 1991

By R. L. Bruening, N. E. Izatt, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and demand for higher performance end products expands. The Molecular Recognition Technology (MRT) process uses highly selective SuperLig® resins to remove desired metals from a variety of solutions in the mining and metals processing and recovery industries. MRT separation processes efficiently produce high purity metal products. In this paper, applications of MRT to metal recovery at mg/L to multiple g/L concentration levels are presented and discussed. Specific examples in the precious metal, nickel, cobalt, zinc, copper, and rare earth industries are given.

Jan 1, 2014

By N. O. Lotter

The connection between mineralogy and metallurgical performance in a plant was recognised long ago (Gaudin, 1939; Petruk, 1976; Petruk and Hughson, 1977; Cabri, 1981; Petruk and Schnaar, 1981; Kinloch, 1982; Peyerl, 1983, Baum et al 1989 for example). The modern toolbox that we now routinely use for flowsheet development took decades to develop (Lotter et al., 2002; Baum and Lotter, 2004; Lotter, 2011 for example). Many workers contributed considerable time and effort to this overall mission of connecting sampling, mineralogy and mineral processing to integrate the flowsheet development activities. Certain key milestones marked this journey, such as Gy’s treatise on the sampling of particulate materials in 1979, which was later added to by François-Bongarçon, Pitard, Minnitt, and Holmes for example. The development of QEM*SEM by Gottlieb et al. of the MLA by Gu et al. constituted a huge leap forward in accuracy and mineral measurement capacity, as well as a reduction in standard errors of mineral characterisation. The advancement of the microprobe to an automated platform made a significant difference to detailed compositional mineralogy. This led to a strong position from which to draw meaningful processing implications from the mineralogical data. Reproducible flotation testing and reliable plant survey material for characterisation was dealt with by, amongst others, High Confidence Flotation Testing ( Lotter, 1995: Runge, 2010, and Bradshaw, 1997); and Statistical Benchmark Surveying (Lotter, 2005), with earlier prototypes which were steadily improved (Lotter, 1994; Restarick, 1976). The sterling work of Napier-Munn in engaging sound statistical methods with mineral processing led to the successful design and use of methods that could identify and quantify small recovery gains in plant scale trials. This history and present capability are reviewed, including leverage into asset management.

Jan 1, 2018

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By J. Cui, Z. Meng, W. Zhao

"The decomposition of rare earth concentrates containing bastnasite and monazite by alkali solutions has been investigated. A slurry of the rare earth concentrate and the alkali solutions was calcined at different temperatures. The impacts of calcination temperature on the decomposition of rare earth minerals, the oxidation of cerium, the deportment of fluorine and phosphorous, and the adaptability of the method to the different grades of rare earth concentrate were all studied. A possible technique for comprehensive recovery is proposed in which the chemical elements such as rare earth, fluorine, phosphorus, calcium, iron and thorium could be recycled or recovered. INTRODUCTIONThe liquid alkali decomposition method is an important technique for the decomposition of mixed rare earth concentrates. The technique is relatively clean compared with the sulfuric acid roasting method. However, its operation is intermittent rather than continuous. The two-step solid-liquid reaction and the subsequent water washing make it not very suitable for mass production and application. An important reason for the disadvantage is that an additional process of ""calcium removal by acid leaching"" is needed for the technique. The content of calcium in Baotou rare earth concentrates is usually 6-12%. The requirement of the current technique is that the content of calcium should be reduced to about 0.2% after the calcium removal process. Otherwise, the decomposition and leaching of rare earth will be affected. Therefore, calcium removal by acid leaching is a necessity before the alkali decomposition process is carried out. Research on different alkali decomposition techniques has been conducted with prior calcium removal by acid leaching (Xu, 1995; Yu, 1993; Han, Li, Chang, Liu & Xu, 1985). There have been some investigations of direct decomposition of the bastnasite (Feng, Pan & Li, 1998; Zhao, Zhang, Yang & Liu, 2002)and monazite (Sun, Li, Li, Su, Zhao & Liu, 1998; Zhou, 2005) by alkali-liquid, however, all studies were carried out in solid-liquid reaction system, and continuous calcination studies have not been reported.This paper investigates the process of direct decomposition of Baotou rare earth concentrates by continuous calcination with concentrated alkali. Using the rotary tubular electric furnace, the mixture of rare earth concentrate and concentrated alkali solution were decomposed continuously. Satisfactory decomposition results were achieved. A method for clean processing and comprehensive resource recovery from Baotou rare earth concentrates is proposed."

Jan 1, 2012

By K. O. J. Sidwell

STRATMAT LIMITED, through its subsidiary, the Strategic Manganese Corporation, controls two adjoining iron-manganese properties five miles west of Woodstock, New Brunswick. One is a staked property of 77 claims traversed by one trunk highway, several secondary roads, and a branch line of the Canadian National railway. The other property, a 20-square-mile Concession immediately to the north-east, is also traversed by an excellent network of roads. Both proper-ties are situated in gently rolling farmland. The deposits were discovered in 1836 by Dr. C. T. Jackson. The first attempt to exploit them was made in 1848 when a blast furnace was erected with a capacity of 7 tons per day. The ore was mined by a series of deep trenches that followed the folds of the enclosing slates. In the late years of operation, bog iron ore from Burton and Maugerville, in Sunbury county, was used in conjunction with the Wood-stock ore. An additional 5-ton furnace was erected in 1863 and mining was carried on intermittently until 1884. No further extensive work was done until 1953. During the period of activity, approximately 70,-000 tons of ore are said to have been smelted ( 1). During these earl y operations the Iron Ore Hill and Moody Hill deposits were partially opened, with the ?bulk of the furnace feed being mined from the Iron Ore Hill workings. The low tenor and apparently limited extent of the deposits, the high. ?content of phosphorus, and the increasing scarcity of fuel, were the chief factors that brought the enterprise to an end.

Jan 1, 1957

By Brian G. Pewsey

Located in the northern part of the Province of British Columbia, the Cassiar Mine started development of its asbestos orebody in 1952, and is currently producing 105.000 tons of asbestos fibre annually. The townsite is nestled in a beautiful valley and supplies more than average facilities. The fibre is shipped to more than 40 countries and is used in many industrial products.

Jan 1, 1978

By M. J. Latva-Kokko, T. J. Riihimäki

"Oxidation autoclaves are normally operated at elevated temperature and pressure. The improvement in kinetics is due to combined effect of temperature and partial pressure of oxygen. In this paper exclusive effect of pressure has been studied with a low grade sulphide ore at below 100 °C temperature. These studies are related to development of a novel tower-like reactor that utilizes hydrostatic pressure. Technology is designed to generate high amount of effective fluid volume for high solid content slurries with lower energy consumption and improved kinetics compared to normal atmospheric operation.INTRODUCTIONEconomical utilization of low-grade ores requires handling of enormous amount of material. This sets new requirements for process equipment in terms of size and energy efficiency. For example on the field of mineral processing this has lead to a six fold increase in the operating volume of mechanical flotation cells over the past two decades. Ore beneficiation methods like flotation greatly reduce amount of material that needs to be further processed in smelters or hydrometallurgical refineries. However with some ore types, such as nickel laterites and refractory gold ores, traditional concentration technologies cannot be utilized. Thus direct leaching of ground ore could be an attractive option. In many cases normal atmospheric tank leaching has traditionally been a non-feasible option mainly due to high capital and operational expenses induced by large amount of stirred reactors required. Main restriction for increasing reactor size to beyond 500 m3 has been mechanical load and power requirements set by mixing in cases when high dispersion efficiency of gas is required. THEORETICAL BACKGROUNDIn hydrometallurgical industry autoclaves are typically operated at elevated temperature and pressure. In many cases increase in operating temperature is the desired phenomena and improvements in kinetics are strongly related to that. Thus increase in pressure might be induced solely by water vapor pressure. However when gaseous feed is present, pressure itself has a strong effect on leaching kinetics for various reasons and its role should not be neglected."

Jan 1, 2012

By Raymond Dallaire

The Humphrey's spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

By Staff, G. M. Hogg

"The eastern portion of the Late Precambrian geosynclinal structure known as the Labrador Trough comprises a 16,000-square-mile sulphide-bearing belt of good potential as a base metal exploration area. Hollinger and Hanna mining interests have carried on exploration in the region since 1953, with encouraging results. This program has been considerable in terms of both effort and expenditure, and has resulted in an apparently successful primary evaluation of the entire belt.Much detailed work remains to be done in the area. Exploration to date has been largely of a reconnaissance nature, employing various methods in common use in Canada today. In the course of this work, several deposits of promise, containing near-economic quantities of copper, zinc, nickel and other metals, have been located. A broad classification of these deposits is proposed.Exploration in the sulphide belt was started on the basis of partial control of the area under mineral exploration concessions. This was necessary to justify operations in an area of difficult access and high operating costs. The results of this now-terminated arrangement are regarded as being of benefit to those directly concerned as well as to the mineral industry in general."

Jan 1, 1966

By Ross D. Lawrence

"IntroductionOne of the methods used when applying the Market Approach to the valuation of a mineral exploration property is known as the Joint Venture Terms Method. The method is particularly useful for the valuation of early-stage exploration properties. Unfortunately, valuators are sometimes imprecise in distinguishing between joint ventures and other types of transactions.At VALMIN '94, Bob Appleyard1 proposed that, if one ignores the time value of money and the probability that the expenditure commitment would be completed, the formula to calculate the value ($V) of a property owned by Party B at the time of the deal would be:$V =$Ex (100-1%)/1% (Formula I)Where $V is the value of the property2Where $E is the expenditure commitment by Party A, andWhere 1% is the percentage property interest to be earned by party A.At PACRIM '99, Mike Lawrence and Graham Dewar3 referred to this method and suggested that there was an ambiguity in the formula proposed by Appleyard in 1994. Mike Lawrence referred to this problem again at VALMIN '014•Lawrence & Dewar suggested that the formulashould be:$V100% =($Ell%) x 100 (Formula 2)Where $V 100% is the value of the entire property,Where $E is the expenditure commitment by Party B, andWhere 1% is the percentage property interest to be earned by Party B.Subsequently, there has been considerable discussion in the AuslMM Bulletin5. In my view, this discussion has touched on a number of useful points, but generally has overlooked one essential element needed for an understanding of the correct application of the N Terms method. That essential element is to understand that there is a material difference between (1) entering into a joint venture arrangement and (2) the purchase of an interest in a property."

Jan 1, 2003

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018