Search Documents

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By Andre du Preez

Emergency Fall Arrest System Rio Tinto?s Primary Objective: ?To achieve repeatable controlled safe deceleration rates during emergency fall arrest activation (Ontario OHSA Regulations) ?Must operate effectively on mine specified steel shaft guides.

May 1, 2013

By M. Cala

Underground coal gasification is technology which enables energy to be extracted from coal beds where mining by means of classical methods is either impossible or uneconomical. The process of coal gasification itself is a complex phenomenon which includes chemical and physical processes: thermal, hydrological and mechanical. Additionally, the analysis of underground coal gasification is difficult to carry out for environment reasons, this being due to the local characteristics of the areas where it is carried out. This paper deals with interaction of geo-reactor with surrounding rock mass, it omits the chemical processes inside geo-reactor itself. Due to the complexity of the processes proceeding and during underground coal gasification coupled with minimal practical experience in using this technology, it is difficult to estimate its influence on the surrounding rock mass. Within this scope, the use of numerical programs can be useful. This paper presents a trial of modeling the processes accompanying underground coal gasification. The processes proceeding and during the underground coal gasification are characterized, and the significant, specific phenomena are discussed, with respect to the influence on the surrounding rock mass. For the chosen processes, examples of numerical calculations are presented. These enabled conclusions to be drawn and also provided directions for the modeling of the underground coal gasification processes.

Aug 1, 2013

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of variables, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By L. Gasser, N. Bellinger, H. Awatta, A. Merati

As aircraft age, the extent of interactions between fatigue and other damage mechanisms, such as corrosion and fretting, increases. At present, however, there is no generally accepted methodology within the Aircraft Structural Integrity Program (ASIP) framework to account for the effects of these interactions on life and the residual strength of aging aircraft components. A comprehensive program is being carried out by the National Research Council Canada in collaboration with Analytical Processes/Engineered Solutions, using the Holistic Structural Integrity Process (HOLSIP) to address time and cyclic load issues. This approach predicts the evolution of a discontinuity state in a material from production to retirement. This paper summarizes the results of a study on the 2024-T3 aluminium alloy in different forms (clad and unclad), thickness, and specimen geometry. This study consisted of identifying the microstructural features associated with crack nucleation sites and relating them to the testing parameters and fatigue life. Several coupons were fabricated and fatigue-tested. The fracture surfaces were carefully examined, and the physical characteristics of the microstructural features found near the crack nucleation sites were analyzed. Effect of stress level, loading direction, coupon geometry and surface condition on the number of crack nucleation sites, and fracture origin size has been discussed. Four distinctive mechanisms were found to be responsible for crack nucleation: for unclad materials constituent particles, oxide residue, surface irregularities and for clad samples the clad layer was the sole fracture origin.

Jan 1, 2006

"A growing public awareness of work-related diseases such as pneumoconiosis and the impact of this awareness on legislative bodies and on the skilled labour market are reasons why the Canadian mining industry must consider dust control of top-drawer importance. Measurements and standards related to the hazard are necessary to control a dust situation and to avoid excessive risk. The author discusses some of the methods of measurement, standards proposed and terminology used in this developing technology. The purpose primarily is to give a better understanding of the basic advances achieved by those who have applied current knowledge with a measure of success."

Jan 1, 1972

By John Wightman

LOCATION OF PROPERTY THE property of Caribou Gold Mines, Limited, is situated in the north-eastern part of Halifax county, seven miles south of the Canadian National railway line at Upper Musquodoboit. Approach to the village is by a secondary road, improved recently by waste rock from the mine dump. A two-wire telephone line, seven miles long, built and owned by the present operators, provides communication to the nearest telephone exchange, Parker's Corner. HISTORY In 1870, the Caribou area was recognized as a proclaimed gold district. From then on, operations were intermittent, with periods of considerable activity by small companies until there were no fewer than seven mines in a district two miles long by three-quarters of a mile wide. These were the Holman, Truro, Caffrey, MacDonald or Elk, Lake, Dixon, and Hilchey properties, all of which have had separate stamp-mills, and have produced gold for varying periods. Depths of the workings range from 100 feet to 1,000 feet. Power was generated at each property by means of steam boilers. At the present time, the Consolidated Mining and Smelting Company of Canada, Limited, controls all the leased areas, approximately 800 acres, and is operating by means of one central vertical shaft. GEOLOGY The district in and about Caribou Mines has an elevation of approximately five hundred feet above sea level. The area is fairly well wooded, with rock outcrops here and there. These outcrops, along with information from test-pits and shafts, have been the basis for the very excellent geological map of the district prepared by E. R. Faribault some years ago. The rock structure, which is one of the best examples in Nova Scotia of an elliptical dome, has its anticlinal axis in a northeast-southwest direction, and flat plunges in the same directions.

Jan 1, 1938

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By K. Mayhew, K. Murray

The CESL Copper Process was developed as a hydrometallurgical alternative to smelting and refining for copper sulphide concentrates. As the majority of such concentrates contain appreciable gold and silver values, effective recovery of these metals is essential to the economics of this technology. Unfortunately, conventional cyanide processing cannot be used on the residue from the copper process, clue to its unusual characteristics when compared with naturally occurring gold and silver ores. An abundance of elemental sulphur, as well as the presence of cyanide soluble copper, leads to the formation of both thiocyanate and copper cyanide which is detrimental to process economics clue to excessive cyanide consumption. This, however, can be reduced to acceptable levels by process innovations such as pressure cyanidation and cyanide recovery. This paper outlines the successful application of the CESL Gold Process to various gold-bearing copper concentrates from bench to demonstration scale.

Jan 1, 2011

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By W. J. Przybylowicz, V. M. Prozesky, D. de Bruin

"The common style of gold mineralization in the Basal Reef and other auriferous conglomerates of the Witwatersrand Supergroup comprises clusters of gold grains occurring interstitially to quartz and pyrite pebbles as well as gold accumulations attached to the surface of and infilling hairline cracks and fractures in round, compact, detrital pyrite. The latter textural association is generally interpreted as a result of remobilization of originally detrital gold during regional metamorphism and related hydrothermal fluid circulation. There is general agreement that, although gold solubility was low, ore modification occurred during the metahydrothermal event, but uncertainty exists about the magnitude and scale of gold remobilization.Micro-textural and chemical investigation of compact round pyrite and associated gold accumulation has established that gold is preferentially deposited on chemically heterogeneous pyrite surfaces. Combinations of alternating high- and low-As zones in pyrite result in mixed np-type conductivity accompanied by electron exchange and the reduction-driven deposition of gold at the cathode. This model does not explain gold accumulations which are not immediately linked to chemical heterogeneities and it is inferred that an additional control on the deposition of gold was exerted by physical defects which lead to zones of increased charge density and/or areas of focussed conductivity. The inferred precipitation mechanisms suggest that submicrocopic physical and chemical controls are the important factors that determined the sites of gold nucleation and that precipitation mechanisms based on physicochemical changes of the hydrothermal system were not involved. The Basal Reef contains on average close to 5OJo of round, detrital, chemically zoned pyrite which provides a large number of electrochemically active pyrite surfaces. The extremely effective electrochemical precipi- . tation mechanism together with the low solubility of gold in Witwatersrand fluids is the main reason for the spatially restricted remobilization of gold in the conglomerate reefs."

Jan 1, 1994

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015