Search Documents

Presentation Agenda ?Background ?OEM Recommendations before RCM ?Operating Context ?OEM Recommendations after RCM ?Reality of Failure ?RCM Deliverables ?Maintenance program optimization ?Spare part optimization ?Implementation ?Further Considerations -Three scenarios ?Summary and Conclusion Background ?P&H Mining?s LCM division performed a RCM study on a ?generic 4100 XPB shovel?in Milwaukee. ?P&H soon realized that the analysis required context -The recommendations were manufacturer knowledge based. -The outcome based on manufacturer requirements. -The strategy was not applicable to all machines, etc. Operator experience and ?local knowledge? are key to the success of an RCM analysis. P&H approached Teck Coal?s Fording River Operation to assist with ?Operating Context?. Teck provided operator and maintainer experience.

May 1, 2010

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By L. Szecowka, M. Poskart, Siwka M. . J.

Oxides of nitrogen, created during combustion, are the most hazardous components of atmospheric pollution. However, it is possible to limit the negative influence of hazardous components on the natural environment. An experimental appartatus was built to determine the influence of the following "primary methods" on the reduction in concentration of NOx: air staging, reburning and flue gas recirculation. The influence of the simultaneous usage of the primary methods on reduction in NOx emissions was also examined. A significant increase in the efficiency of NOx reduction was achieved in two cases.

Jan 1, 2004

By K. Fagerlund, L. Rosenback, T. Mäkinen, Y. Anjala

This paper deals with the nickel smelter and refinery concepts Outokumpu has applied at Harjavalta and several other plants. Also other process routes and modifications developed and tested by Outokumpu during the recent years are highlighted. Outokumpu started nickel production in Harjavalta in 1959. Until 1995 the Flash Smelting - Peirce-Smith (PS) converting route was applied. High grade nickel matte from the converting step was further refined by means of leaching and electrowinning to produce cathode nickel. In 1995 the nickel production capacity was increased from 17 000 t/a to 52 000 t/a based on the Direct Outokumpu Nickel Smelting Process (DON). In the DON process PS converting is eliminated and high grade nickel matte with low Fe-content is directly produced in the flash smelting furnace (FSF). Metal values from the smelting slag are recovered in the electric furnace (EF) as iron containing Ni-matte. The DON process can be operated with either two matte concept, where high grade FSF matte and EF matte are produced, or a single matte concept, where EF matte is recycled to the smelting furnace and thus only one type of high grade matte is obtained. The additional refinery capacity at Harjavalta is based on hydrogen reduction producing.

Jan 1, 2005

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By R. C. Gilmore

Underground longwall coal mining sections may develop explosive mixtures of methane-air in the mined-out gobs. If the panel are operated as bleederless or sealed gobs, progressive sealing along the gate roads as the longwall face retreats limits the flow of fresh air into the gob and thus deprives potentially explosive atmospheres of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics (CFD) modelling to simulate the flow of gases in longwall gobs. Modelling indicates that targeted injection of nitrogen through the seals along the gate roads inbye the face can be used to control the size and location of methane and air clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures in longwall gobs.

Aug 1, 2013

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By Carrasco .. P. J. A., R. Parada, I. Saavedra, F. Parada, R. Parra, E. Balladares

In most of the smelters, the management of flue dust has a double objective: the control of minor elements in the anodes and the management of volatiles compounds that can cause contamination due to fugitive gas emissions. This is a special concern when high content of Va elements (As, Sb & Bi) are present in concentrates. We present the results of the experimental study to prove the principle of a novel process that recovers, via volatilization, the As, Sb and Bi in the flue dust as gaseous sulfides, due to a previous sulfidization. In the case of as control any further classical treatment for its stabilization is possible from the gas. The clean calcine can be returned to the smelter avoiding any concentration of these minor elements in the circuit. This process is now tested at pilot scale and shows better indices on carbon footprint than the classical hydrometallurgical process for flue dust.

Jan 1, 2011

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited available technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "observational construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of a mountain tunnel (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert et al. requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electro-optical distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily management measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this proposed method. It then presents the typical results of a field demonstration test at a tunnel under construction. Lastly, the predictable range from the stratum boundary at which ground stiffness changes are discussed based on the results of three-dimensional numerical analysis.

Jan 1, 2015

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By N. Erarslan, M. Serati

"This paper attempts to provide a simple analytical solution for the calculation of the stress tensor induced in a two-dimensional elastic ring of a brittle material subjected to general loading on either its internal or external curved surfaces. Airy stress functions and Michell’s expression in polar coordinates are used, and parametric studies are performed to investigate the influence of loading angle and the geometrical aspect ratio of the ring on the maximum induced tensile stress. INTRODUCTIONA proper and accurate estimation of the tensile strength of a given material is a crucial step in many engineering projects; in particular in rock cutting, since rocks are much weaker in tension than in compression or shear. Both direct and indirect laboratory techniques such as the direct uniaxial pulling test, the Brazilian indirect tensile test (also known as the split cylinder test), and the ring test have been proposed and developed to estimate rock tensile strength. Among these, the ring test, initially suggested by Ripperger and Davids (1946), has become particularly appealing for its ease of sample preparation and its unique breakage mechanism in almost a pure tensile mode. Unlike the Brazilian test in which high shear stresses developed in the vicinity of the contact could interfere with the tensile breakage of the disc specimen, a tensile failure starts away from the loading platens in a ring test (Hobbs, 1964)."

Jan 1, 2015

By Tai Sik Lee

Why ISRU into Space Exploration are important NASA and International Mission statements calls for the sustainable human exploration of the Moon, Near-Earth asteroids, and Mars Common Exploration Goals and Objectives are Strongly influenced by ISRU Extend Human Presence: Continually increase the duration and level of self sufficiency at all destinations Develop Exploration Technologies and Capabilities: Develop and validate tools, technologies, and systems that extract, process, and utilize resource to enable exploration missions Perform Science to Support Human Exploration: Characterize available resources at destinations Stimulate Economic Expansion: Encourage commercial services and create new markets, including markets for discovered resources Enhance Earth Safety: Test techniques to mitigate the risk of asteroid collisions with Earth

May 1, 2013

By P. J. Sylvester, S. J. Piercey, S. Maloney, S. M. Brueckner, L. Pilgrim, D. Hyde, G. Ogilvie

The 1806 zone is part of a Au-rich volcanogenic massive sulfide deposit at the Rambler Camp on the Baie \/erte Peninsula, northwestern Newfoundland, and is characterized by high Au grades (3.97 g/t), relatively low Cu and Zn grades (0.60 wt% Cu, 1.17 wt% Zn), and moderate Ag grades (27.83 g/t) at ca. 0.37 Mt ore. Gold and Ag occur as electrum and different Ag varieties including Ag-Hg ± Au alloys, miargyrite, and pyrargyrite that occur often in close proximity to electrum. Additionally, Ag-, As-, Sb-, and Sn-bearing sulfosalts are frequently observed and usually close to electrum. These textural relations strongly favor a syngenetic/magmatic origin for the 1806 zone, despite having a metamorphic overprint.

Jan 1, 2011

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By F J. Pearce

The Steel Company of Canada, utilizing the S-L process, has produced partially and highly reduced pellets for use in the blast furnace. Experimental blast furnace tests, using reduced pellet burdens, have been carried out. The changes in production rate, fuel rate and general performance of both the S-L and the blast furnace processes are indicated. Introduction T HE ore burdens for a blast furnace may be improved in two ways: chemically, by concentrating the ore to a high degree of purity; and physically, by agglomerating or closely sizing the ore particles. Today, many b1ast furnaces are charged with closely sized agglomerates, some of which contain upwards of 66 per cent iron. The further improvement of these burdens by chemical concentration may, in many instances, be uneconomic due to the large losses of iron that occur during processing. Assuming that it would be possible to reject all of the gangue minerals, the maximum level of concentration of iron in the hematitic ores would be only about 70 per cent.

Jan 1, 1964

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015