Search Documents

Separation in magnetic fluids is one of the modern techniques that offer a unique approach to material manipulation in a broad spectrum of industries. Its wide-scale application has been restricted so far for a variety of reasons, including limited throughput, inefficient recovery of magnetic fluids and the cost of commercially available magnetic fluids. This situation has changed recently. Very selective separators, with automated density control, capable of treating a variety of materials in a wide spectrum of densities and particle sizes have been built by DebTech and applied in the diamond industry. Technology for the recovery of magnetic fluids has been developed and low-cost magnetic fluids, with high magnetisation and low viscosity are being produced on a production scale. Scale-up of the technology has been addressed and units capable of treating large tonnages of material have been designed. Such a development thus offers the minerals industry a technology that surpasses the existing technologies in selectivity, efficiency and versatility

Jan 1, 2000

The Illawarra Branch of the Australasian Institute of Mining and Metallurgy over recent years has established an enviable reputation for organising and conducting conferences, colloquia and symposia. And this Symposium must surely enhance that reputation. The subject of the Symposium, Seam Gas Drainage has become a matter of great import- ance to the Australian Coal Industry in a comparatively short time. Our short experience being due to our operations, until recent times anyway, not being unduly affected by gas. The Australian Industry, by virtue of its mines getting deeper and higher rates of extraction being required is now encountering the difficulties with gas which have for so long been part of the coal mining scene in many other countries. Because these gas emissions affect our working conditions by way of creating hazards and affect our production by way of bringing about cessation of operations from time to time this Symposium must be regarded as being very timely out here. I must congratulate the Branch Committee on the general set,yp :o.f the programme of papers. The classification of papers into four groups and the sequence in which the papers were presented provided an excellent flow through from introduction to finality. It is not my intention to further discuss individual papers - already they have been well discussed in this forum and as I understand it outside in the early hours of the morning,

Jan 1, 1982

This short paper outlines the authorÆs views regarding the progress we have made as an industry in managing mining assets over the past 500 years. It represents a personal view û but one founded in fact-based observations of mining companies and of the mining industry in general. There is no doubt that AgricolaÆs views as expressed in De Re Metallica (1556) were visionary. There is also little doubt regarding another issue û that whilst a great deal has been learnt about the management of mines since AgricolaÆs time, observations suggest that best practice management is the exception rather than the rule across our industry. Although insights regarding the successful management of mines have become apparent, we still witness unnecessary errors in our industry that lead to the loss of shareholdersÆ funds. By highlighting some aspects of current best practice, particularly in the arena of operations management, it is hoped that this short paper contributes a small step along the next 500-year-long learning curve. The paper concludes with a brief description of the progress and impact of continuous improvement initiatives at Kalgoorlie Consolidated Gold Mines (KCGM). Located in the Kalgoorlie Goldfields, KCGM is currently AustraliaÆs largest gold mine producing over 800 000 ounces of gold per annum. Improvement initiatives at KCGM look set to deliver some $100 million in value over life-of-mine.

Jan 1, 2004

Pipe Jacking has been a recognised method of tunnelling in the U.K. since the early 1950's, although I understand that pipes were pushed blind by the soldiers in the first World War from trenches on the Allied side to, or adjacent to, trenches on the German side, thus allowing explosives to be used with a certain element of surprise! 'However, on its more conventional to the U.K. in the 1950's, Pipe Jacking made considerable inroads into the tunnelling market place as an alternative to timber supported headings. This success was, unfortunately, fairly short lived because, owing to its simple method of operation, contractors paid insufficient detail to the engineering (or surveying) aspects and as such the system soon had a bad reputation for unreliability and lack of accuracy. Due to these failings, the market was not exploited and, therefore, there was a lack of investment by contractors, pipe manufacturers and also by any client, or research organisation, which is client associated. The effect of this meant that the system stagnated for a number of years and was used generally only for short crossing work (i.e. railways, canals and motorways), and then only in good homogeneous ground. Albeit, a limited number of full scale sewage disposal contracts were carried out, but with the lack of knowledge and experience of the clients, contractors and suppliers, (particularly the pipe suppliers), no reasonable success, either physical or financial, was achieved on any such contract.

Jan 1, 1987

By G P. J Dijkema, M A. Reuter

From a material cycles perspective all processes are interconnected and consequently a process can never be evaluated as an isolated and independent unit. This also holds true for the evaluated co-incineration options. Environmental and sustainability issues for example, such as raw material and energy utilisation or air pollution, are a resultant of the whole system of industrial activities. It is therefore important, not to optimise a single process or industrial activity, but rather the whole system. Although engineering procedures for the design of individual industrial units are well developed, the problem of determining the best arrangement of these interconnected units is often far more difficult. Regulation that manages the arrangement of the units for waste processing is still under construction. In the evaluation of co-incineration, analogous principle from process control can be used: feedforward control. This principle includes the determination of which outlets can be used for all process outputs, hence avoidance of any æunusableÆ products or wastes possibly arising from co-incineration. To establish the extent, to which produced wastes are usable, a system overview is necessary, in addition to in-depth information on the subsystems, which produce and can consume wastes. Material cycles modelling can be used as the basis for a tool that supports the development of a suitable playing field. It should provide overview of the system and in-depth information on its subsystems. This tool then represents an attempt to bridge the gap between æholisticÆ industrial ecology and process engineering.

Jan 1, 2000

It is generally known that Charters Towers was discovered by Mosman, Clarke and Fraser in 1871. However, the time was ripe, and these three were barely in front of others. There is one account that prospectors from Ravenswood visited the area months before but decided it was too far from water, and that one of them had told Mosman and party of the find. There is another account that Joe Larkins found the discoverers before they had registered any ground - this may explain Mosman's quick departure for Ravenswood.When the news spread, the rush was rapid, and there was soon a sizeable population: probably too many, as within twelve months the infant settlement was under considerable stress. First, the presiding Gold Commissioners had adopted "unusual and arbitary" interpretations of the Regulations, and many of the miners were aggrieved; Charters, the senior Commissioner, was accused of favouring moneyed interests, and of retiring ill whenever a brawl or confrontation occured. As a result, the law of the field soon became "the survival of the strong". Second, the settlers were, divided on where the main town should be: Millchester, near the water, or Charters Towers near the mines. Third, the discovery of gold at the Millchester Deep Lead in August, 1872 was followed by highly exaggerated accoants in_' the southern papers, apparently fabricated by local business speculators. The resulting rush resulted in hundreds of unlucky prospectors having to return or seek other fields. In that period two men were killed in squabbles over ground. To make matters worse, by October 1872 a drought had set in, water cost three pence a bucket, fodder was scarce, cartage expensive, and the price of crushing ore rose to thirty shillings per ton.

Jan 1, 1986

By P Cameron

Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised. In 1970 Alban Lynch promoted two practical ideas to improve plant operations: Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie to design and to optimise) complete mineral processing circuits. Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant. Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation. Models of comminution and classification developed at the JKMRC have been used since the early-1980s. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill? projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product. JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry. These include: commercial software (JKSimMet, JKSimBlast and JKMetAccount); monographs (Comminution and Blasting); technologies (Mine-to-Mill? and flotation optimisation); and hardware products (JKFrothCam, JKJetLift? and the Mineral Liberation Analyser). This paper summarises these technologies and their benefits.

Jan 1, 2002

By M Donatelli, E Grazio, A Heissenberger

The distribution of a contaminant in a bulk mass greatly influences the effectiveness of sampling procedures. Most currently used sampling guidelines for genetically modified organisms (GMO) testing have stringent distribution requirements. Specifically, all these protocols are based upon the assumption that GM material, if present, is randomly distributed. Yet, assuming randomness is risky because the applied sampling plan may not provide an accurate estimate of the content of the contaminant. Despite the general consensus that an evaluation of the possibility of non-random distribution of GM materials within lots is a pre-requisite for the definition of effective sampling protocols, no experimental data on the distribution of GMOs in kernel lots are available anywhere in the world. Additionally, to date there is no distribution-free statistical model to estimate sampling errors, thus making the theoretical definition of optimal sampling technique impossible when randomness cannot be assumed. Here we present preliminary results of the KeLDA project, which is the first study investigating the distribution of GM materials in large soybean lots imported within the European Union. The extensive variability of GM content, observable both within and among soybean lots, indicates that heterogeneity issues cannot be overlooked when defining sampling strategies for large lots of particulate material and that randomness cannot be assumed a priori. A new statistical model free from any distribution assumptions, developed in order to estimate the sampling error associated with different sampling protocols together with the risk of false-negative results, is also presented. The new model, which is applicable to any consignment of particulate material with respect to any kind of contamination, presents two novelties: first, freedom from any distribution assumption; second, the possibility of estimating the magnitude of the sampling error associated with different sampling protocols as a function of specific distributional properties.

Jan 1, 2005

By M P. Schwarz

A major issue presently faced by companies producing and processing iron ore is the need to maximise throughput while minimising capital expenditure. While present high demand means this is of prime importance, the perennial issues of maintenance, operating costs, reliability, quality and environmental sustainability are also critical to profi tability. Attempts to address these issues generally require modifi cations to existing equipment, or trials of new equipment when designing plant for new projects.The risk involved can be substantially minimised by testing equipment improvements using advanced computational models prior to implementation. Examples of application of Computational Fluid Dynamics (CFD) and Discrete Element Method (DEM) modelling to sampling, cyclones, conveyor transfers, classifiers, dust control, banana screens, comminution and smelt-reduction will be given to illustrate the benefi ts of such an approach. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

The Mount Whaleback iron ore deposit at Newman, Western Australia comprises the largest known continuous iron ore deposit in Australia, originally with a Measured Resource in excess of 1700 Mt of hematite ore. The deposit occurs within the Hamersley Province which forms part of the Pilbara Block in the NW of Western Australia (Figure 1). The Mount Whaleback iron ore deposit, together with a number of discrete iron ore bearing satellite orebodies in the Newman district, contributes to the Newman Lump and Fines products. Extensive quality control systems are utilised from mining to shipping to ensure that each product meets a narrow geochemical target grade range.

Jan 1, 1997

Background A recent development in many industries,' including the mining industry, has been ever increasing acceptance and adoption of extended (12-hour) shifts and compressed work cycles compensated by more time off work by employees between cycles. In the Western Australian mining industry development of `long-distance-commute' (LDC) coincided with adoption of 12-hour rotating shifts. Preludes to LDC were the `construction-style' rosters with two crews plus allowance for annual and sick leave relievers working the statutory 13 consecutive shifts followed by one shift off. Crews rotated day to night shift weekly or at fortnightly intervals. Average hours of 72 to 78 per week were common. The author had personal experience working these rosters in the East Pilbara of Western Australia from 1977 to 1982. Workers tolerated these rosters until a suitable combination of frustration, boredom, despair and the `Five Grand Fever' triggered them to `pull the pin' and head for relaxation in Bangkok, Manila, Nimbin, or Margaret River according to their personal tastes.

Jan 1, 1996

Continuous improvement in environmental management assists in the achievement of sustainability goals for the processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. Case studies are presented for a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided.The auditing process as described here for coal mines, and coal handling and preparation plants, is equally applicable to the processing of other mineral ores, metalliferous mines, quarries, and oil and gas projects.

Jan 1, 2004

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By Neville Rockhouse

This paper examines the interrelationship of conducting full risk assessments in the context of the coal mining industry and under the framework of the Health's Safety in Employment Act 1992. In the context of Occupational Health's Safety, Risk Management is a holistic management process that can be used by individuals working in all organisations and from all industries. The Australian New Zealand Standard 4360: 2004 defines a Risk as being; The chance of something happening that will have an impact on objectives. This definition is followed by several notes that include: a risk is often specified in terms of an event or circumstance and the consequences that may flow from it, risk is measured in terms of a combination of the consequences of an event and their likelihood, and risk may have a positive or negative impact. For the purposes of this paper, the above definition will be adopted. This paper examines the newly expanded approach of the fully documented risk management process in the New Zealand coal mining industry. This is done in the context of the coal mining regulations but more importantly by using the framework of the Health & Safety in Employment Act 1992. This legislation under Section 6 requires all employers to, Take all Practicable Steps to prevent harm coming to employees while at work and to others who might be at or in the vicinity of a workplace. When the term 'all practicable steps' is studied, one can clearly see that such steps should be the same steps taken that a prudent and reasonable person would have taken given the same type of circumstance. Due to the fact that in New Zealand parliament made statutes is administered by a Government Department, means that their breaches will be heard before a judge in the District Court. Under the Westminster System of Justice, a basic dictum of that court in matters relating the occupational health and safety is that a breach needs to be satisfied to a specific standard. That standard is, 'Beyond a reasonable Doubt'. One of the primary benefits of adopting a proactive approach to risk management is that if the industry were to adopt similar approaches, then this mythology could be seen as an industry standard. As such, the approach carries the same status in a court of law, as that of an Approved Code of Practice.

Jan 1, 2007

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral

Jan 1, 1995

By H Durrant, P I. Corke, J Cunningham

This paper reviews the state-of-the-art in the automation of underground mining vehicles and reports on the development of an autonomous navigation system under development through the CMTE with sponsorship arranged by AMIRA. Past attempts at automating LHDs and haul trucks are described and their particular strengths and weaknesses are discussed. The auto-guidance system being developed overcomes some of the limitations of state-of-the-art prototype æcommercialÆ systems. It can be retrofitted to existing remote controlled vehicles, uses minimum installed infrastructure and is flexible enough for rapid relocation to alternate routes. The navigation techniques use data fusion of two separate sets of sensors combining natural feature recognition, nodal maps and inertial navigation techniques. Collision detection is incorporated and people and other traffic are excluded from the tramming area. This paper describes the work being done by the group with regard to auto-tramming and also outlines the future goals.

Jan 1, 1998

By A H. Hofstra, G P. Landis, P Emsbo, A G. Hunt

Models of the evolution of the hydrothermal systems that form porphyry Cu (Mo-Au) deposits are compromised because aqueous magma-derived fluids in the ore zones of most deposits have changed from their original magmatic compositions as a result of cooling, depressurising, mineral precipitation, brine-vapour unmixing and fluid-rock reactions. However, in deep quartz-rich, sulfide-poor veins from numerous porphyry type deposits, we have identified parental fluids trapped in inclusions at near magmatic temperatures and pressures above the brine-vapour unmixing solvus. We have analysed these inclusions for bulk salinity, density, solute chemistry, helium isotopic ratios and elemental composition. These parental inclusions contain 35 - 70 volume per cent bubble, are low to moderate salinity, contain up to ten mol per cent CO2, and commonly contain a chalcopyrite daughter crystal. Our results indicate that these Cu-rich fluids transport Cu from a plutonic complex below upward into a hydrothermal system, where decompression, cooling, unmixing and water-rock reaction drive ore-mineral precipitation. Na/Cl ratios greater than one indicate that in addition to chlorine, sulfur and/or carbonate must play a key role in Cu transportation. Helium isotope ratios indicate that between ~15 and 100 per cent of helium in these fluids is mantle-derived. We suggest that in addition to He, volatiles from mafic magmas in the mantle are also likely to supply CO2, Cu and S to the fluids that form porphyry copper deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000

This paper examines some of the important aspects of mineral taxation policies and practices, with reference to the mining tax regimes of selected Pacific Rim countries (see Tables 1 and 2). The following subjects are addressed:what is æmineral taxationÆ?, basis for mineral taxation, types of mineral taxes, objectives of the mineral taxation regime, best practices, and mineral royalties. Many countries, in some cases with the encouragement and assistance of international funding agencies, are actively assessing the international competitiveness of their mining tax regimes with a view to attracting investment. However, these countries recognise that the mining tax regime is not the only consideration that is taken into account by prospective investors. The countryÆs geological prospectivity, physical infrastructure, labour force, political risk, and regulatory system are also important factors in the investment decision making process. Although it is probably true that an attractive mining tax regime will not necessarily attract mineral investment, there is a real possibility that an unattractive regime can drive away investment. For example, Hugo Dummett, general manager for discovery at BHP, hinted recently that BHP could cease exploration in Russia in the absence of positive tax changes. Dummett is reported as saying that if taxes æend up being as onerous as they are now, we really have to rethink why we are hereÆ (Mining Journal, London, November 27, 1998).

Jan 1, 1999