Search Documents

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

Mine Dewatering for reoccupation of a flooded mine requires rehabilitation and recommissioning of shaft and sane level functions to provide safe efficient access, services and logistics, as well as securing connections with all exposed workings. The objective is the earliest secure reoccupation of the target depth horizon for minimum water pumping, consistent with an appropriate investment and optimum schedule of operating inputs to the dewatering, redevelopment, services and consolidation processes. Strategy must focus on recommissioning of relevant functions in the shaft and at stage pumping horizons, advance of logistics close to pumping and rehabilitation, management of the secured exposed workings. The progress must be systematic, sustained and integrated, and must be secured against risk and uncertainty. There must be a strategic capability to respond effectively, and manage interruptions to processes, conditions requiring higher or different resources, and contingencies which affect schedule, budget or risk profile for the continuing programme. Planning must aim to reduce or contain risk or uncertainty elements and contingencies, limit interruption frequency and severity, identify and provide the capability for efficient responses. It is appropriate to model and simulate the reoccupation analogous to a mine initial development production programme. Only minor changes to relationships and relativities of models for Capital works, Operations (Production and Development) and Services/Logistics are needed but the model for management of workings is more relevant than that for depleted workings in an operating mine because of the water and other transfers. An important difference is the unsteady state of operations which requires probabilistic modelling of availability and utilization of equipment and processes.

Jan 1, 1988

By P Cepuritis, G Chitombo a, I Brunton

There is a significant amount of past evidence that links blasting and occurrences of slope failure. Particularly of great concern at Telfer Gold Mine is the effect of open pit blasting on the stability of the footwall slope above the underground portal and the stability of underground structures. For this reason, Newcrest Mining Ltd invited JKMRC to conduct necessary field measurements and numerical modelling with the following objectives:assess the dynamic stability of the footwall slope above the portal; assess the characteristics of current and future blasts in the open pit; and prepare open pit blasting guidelines that will minimise the detrimental effect of blasting on slope stability. To achieve these tasks it was necessary to develop a scaled distance attenuation curve for blast vibrations. In order to validate the developed vibration attenuation curves it was necessary to monitor vibrations from a production blast. Using JKMRC blast design software tools, the vibration of the production blast was also modelled from the blast design and vibration results from single hole blasts. The intention was, assuming that the observed and modelled vibrations were close in terms of frequency and amplitude, to use the software tools to model the vibrations of future blasts and assess their likely effect on slope stability. Numerical modelling of the dynamic stability of the footwall slope was done using the FLAC finite difference code and the UDEC distinct element code. The results of the numerical modelling and of the field measurements of the blast induced ground vibrations were combined into the blast design rules that relate distance between the slope and the blast, charge weight per delay and number of blasts necessary to cause failure of the slope.

Jan 1, 1999

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

By I B. Miller

Magnesium International Limited (MIL) has broken new ground in their desire to integrate their mineral development activities in the Southern Flinders Ranges of South Australia in to the communities of the region, despite there being no statutory requirement to do so. In their efforts to define a magnesite resource adjacent to the proposed site for a magnesium metal processing facility, MIL opened their exploration program up for public consultation. In conjunction with the Port Pirie Regional Development Board (PPRDB), a community group was formed to review the impact of exploration and mining on the ecologically sensitive Southern Flinders region. This voluntary move towards full community consultation for mineral exploration was a first in South Australia and probably in Australia. The Community Focus Group (CFG) worked closely with MIL, Primary Industries and Resources of South Australia (PIRSA) and the Department for Environment and Heritage (DEH) in the development of an exploration program and Declaration of Environmental Factors (DEF) acceptable to all stakeholders. Collaboratively, the community concerns were discussed and addressed, with the community gaining a very comprehensive understanding of the exploration process and possible future mine development. A balance of social, environmental and economic factors was developed that was accepted by all parties and encapsulated in the final DEF for approval by the regulatory authority. The consultation process was a new experience for all of the stakeholders, each of them effectively exploring new ground in addressing information dissemination, risk management and the social versus economic equation. MIL developed not only a viable and acceptable exploration program but also substantially reinforced its position as a responsible corporate citizen with the Southern Flinders communities.

Jan 1, 2004

By J Barnes

During September 2000, Nabalco management identified the need for a corporate system to deliver its key performance indicators (KPIs). In June 2001, a need was also identified to replace the existing metallurgical accounting system. After a review of the technologies available, the decision was made to develop the systems in-house, in preference to purchasing commercial software packages. This would allow much greater control over the structure, and provide for an iterative, concurrent development process between software and key business developers. This has proven invaluable in the development process. The purpose of the KPI system is to provide a unified reporting tool for all performance indicators. These indicators include production, safety, health and environment, personnel, costs, continuous improvement initiatives and opportunity losses. All of these disparate measurements are brought together into the KPI system and used to determine the performance for each department or area. The general principles of the balanced scorecard business approach (Kaplan and Norton, 1996) are applied to achieve a performance measurement for each area within Nabalco. The new metallurgical accounting system (MA) is a SQLServer database with web page and Excel interfaces. The database is structured around daily inputs of all measurements and calculations. The data is stored and adjustments and reconciliations can be made to this data as required. The focus is on accounting rigour, with all adjustments recorded in the database to allow for full auditing. The structure of the data focuses on the five input/output streams (bauxite in, caustic soda in, fuel oil in, residue out, and alumina out). In-circuit inventory provides a secondary measurement on which to check and calibrate the MA system. The KPI and MA systems were developed using Web technologies and are available to any internet-enabled device with Internet Explorer installed. This removes the need for software rollouts and user training. This will promote the wide use of the systems throughout Nabalco and Alcan.

Jan 1, 2002

By A G. L Pratt, C Rossetti

The implementation of mass mining methods for large metalliferous deposits has led to the development and application of increasingly sophisticated automation and condition monitoring technologies in these mines. This technology aims to increase safety, equipment utilisation and monitoring of critical aspects of the underground ambient and geological environments. The communications networks required to support these aims and their associated technologies have evolved accordingly, and have done so in a demanding underground environment. The evolution of communication infrastructure for large underground mines has developed from basic analogue telephony to high-bandwidth optic fibre based systems. The latter is now the media of choice. More recently the developments in wireless broadband equipment designed specifically for underground environments have emerged to satisfy the needs of automation for mobile equipment and shaft conveyance communications. The use of internet protocols for industrial control and monitoring has led to the application of ethernet-based backbone networks as a standardised approach. There may also be a need for the integration of range of communications platforms in a mining operation to realise the full advantages offered by automation and condition monitoring technologies. As a result the design of the communications backbone networks for underground mines has started to become the domain of information technology professionals. Without these networks, the analysis of equipment utilisation is often not possible. The improvements that can be brought about by æsweating the assetsÆ and the transmission of business critical information are the most significant benefits of an integrated communications system. These benefits far outweigh the costs of strategic planning, subsequent specification and implementation of communication networks themselves. Future developments in mining systems and communications technology will continue to drive the demands placed upon communications networks as an essential mass mining infrastructure item. This paper outlines the benefits of secure high bandwidth backbone communications networks for mass mining operations and the need for a high degree of strategic thought and demand forecasting in the planning stages for these operations.

Jan 1, 2008

By Murray G

This paper outlines the processes involved in acid generation from sulphides and the key factors in identifying and predicting time dependent changes in the nature of acid mine drainage (AMD). The initial characteristics of mine water; whether drainage from exposed mining faces, runoff and seepage from waste dumps or seepage from process tailings; do not necessarily reflect the long term potential for AMD. The ultimate quality of mine drainage is a function of the interaction of many chemical, physical, biological and engineering (operational) factors. Techniques are available that can predict the qualitative nature of acid generation and mine drainage quality but accurate quantitative predictions are essentially impossible at the present time. As more and more mining operations exploit sulphide ore, the AMD and acid waste issue will become a. far greater concern. The significance of time dependent factors in the production of acid mine drainage-.is not just restricted to particuL.ar mine sites but needs to be recognised by the mining industry as a whole.

Jan 1, 1988

Sophisticated pit optimisation software has allowed mine planning engineers to generate mining outlines that consider the numerous factors that have a major effect on the success or otherwise of a mine plan. The outlines are generally generated using a range of values for which one can assume a fixed mining cost and a variable revenue. During analysis, the expected costs and revenues are used to investigate the cashflow and sensitivities. Ultimately, the final pit and incremental outlines, or shells, are selected for a given expected price. This paper proposes an alternative method for incremental pit shell selection that considers the risk the mine be prepared to accept. The life of mine is divided into a number of Business Risk Periods (BRPs). The BRP represents the period of time over which the owner is prepared to invest capital. During each BRP, the mine will then operate at a selected investment cost which is generally equal to or greater than the minimum required to meet production targets. In this way, a robust mine plan can be produced which allows the mine to react to change without having to alter the incremental shell limits while maintaining a strategic risk profile. This paper will summarise factors to be considered in selection of the BRP and the incremental pit shells within the BRP.

Jan 1, 1998

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

As defined by both the Australian and New South Wales Governments the Illawarra consists of the Tablelands, the Local Government areas of WingecarribPe Shire, Bowral Municipality and Mittagong Shire, the Wollongong sub-region consisting of Wollongong City Council, Shellharbour Municipality and Kiama Municipality and finally the Shoalhaven Shire. I intend here to concentrate on community development in the Wollongong sub-region.

Jan 1, 1976

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

By Willey GJ

A brief test program was undertaken to assess the viability of air-sparged hydrocyclone beneficiation at the Cadjebut concentrator. Three different process streams were processed (lead rougher feed, lead scavenger tail and `mine water' solids) in a small scale ASH unit (one litre volume, feed rate 1000 to 1800 kg solids/hour). Analysis of the concentrates indicated that ASH based flotation was successful, selective and capable of achieving improvements to the overall metallurgical performance of the concentrator. The flow regime inside the device accentuates the selective flotation of the finest particle size ranges generally not recovered to any significant extent in conventional mechanical flotation devices. The testwork proved that the ASH is a viable alternative option for increasing the flotation capacity of the lead beneficiation stage of the Concentrator.

Jan 1, 1993

An extensive study was carried out to evaluate the performance of Outokumpu OK50, OK38 and Maxwell MX14 cells at ComincoÆs Red Dog flotation concentrator in Alaska. Tests were conducted by varying operating conditions of the cells installed in different circuits in the plant. The hydrodynamic and gas dispersion properties were measured and the metallurgical performance of the cells was evaluated for each condition used in the tests. This paper highlights the importance of superficial gas velocity, bubble surface area flux, gas hold-up, power consumption, residence time distribution and froth flow behaviour in optimising cell performance. The findings of these tests provide valuable insights into selection of the best cell operating conditions to optimise circuit performance.

Jan 1, 2000

By A Thompson, E Villaescusa

The Western Australian School of Mines (WASM), Kalgoorlie, has been performing dynamic testing of reinforcement systems as part of the Minerals and Energy Research Institute of Western Australia (MERIWA) Projects M349 and M349A sponsored by WASM, the Western Australian State Government and the mining industry. These projects have resulted in the construction and commissioning of the WASM Dynamic Test Facility and a program of reinforcement system testing. The primary purpose of the WASM projects is to evaluate the performance of complete reinforcement systems when subjected to an axial dynamic load. The test procedure, monitoring and associated analysis enable assessments for each component (ie the element, the internal fixing mechanism and the surface hardware) of the reinforcement system. The performance of a reinforcement system is usually defined by a static force-displacement response to axial loading. However, this static response may not be applicable to dynamic loadings associated with violent failure of rock due to overstressing as mines progress to greater depths. It was therefore appropriate that the responses of reinforcement systems subjected to dynamic loading be defined and evaluated. The key findings from the tests on a number of reinforcement systems are presented and recommendations made regarding their application for dynamic loading.

Jan 1, 2008