Search Documents

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By E Werner, J J. Donovan, A J. Morris

Coal mining in the Pittsburgh coal seam, in the eastern United States, began in the late-1700s. Since that time numerous mining technologies have been used throughout the basin. Environmental concerns, particularly mine discharge quality, have only been considered since the early-1970s. During the last 20 years, many of the larger underground mines have closed and are now either flooding or already flooded. In order to understand the consequences and potential future effects of this flooding, mine mapping of the basin has been compiled utilising a geographic information system (GIS) with an emphasis on locating barrier pillars between mines. Mine flooding has been monitored at numerous sites utilising pressure transducers and data loggers. These data have been combined with historical data from mining companies and structure contour maps to yield chronological flooding maps of the basin from 1980 to present. Utilising these maps and the indicated flooding rates, future discharge locations have been identified along with estimates of when these discharges are likely to occur. Related work has identified barrier pillar hydraulic conductivities and vertical infiltration rates as a function of overburden thickness. All of this information has been integrated into a groundwater flow model that simulates mine flooding. This model is useful in defining mine to mine interactions as the various mines fill with water, and the testing of various flooding scenarios. The model will be used in evaluating mine discharge rates and evaluating the options for regional mine drainage treatment.

Jan 1, 2003

By D Bradshaw

The recovery of molybdenum at Kennecott Utah Copper (KUC) has become increasingly important as its demand and price have risen dramatically in the last few years. Consequently, the flotation behaviour of the molybdenum bearing mineral, molybdenite, has received a significant amount of attention. The flotation performance of molybdenite generally lags that of the copper sulfide minerals and is much more variable. There are many factors including particle size, liberation, surface slimes and oxidation that contribute to this and also much speculation as to the relative contribution of each of these factors. This paper discusses the morphology of the molybdenite found at KUC, the mineral associations in the different lithogical ores types and the effect that each of these has on flotation performance. Quantitative mineralogical analysis and an assessment of particle shapes are used to explain that flotation behaviour does not necessarily follow expected trends and that some behaviour is counter-intuitive. This unique behaviour can be explained by the morphology and anisotropic nature of molybdenite.

Jan 1, 2008

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

Stability on surface mining projects is primarily controlled by five factors. These include structural geology, the most important of the factors, the existence of weak layers, primarily clayey gouge or clay infill, groundwater, blasting and weathering. Case examples of stability on many surface mines including some coal mines are presented. The experience and lessons learned are applicable in some way to stability of surface coal Mines.

Jan 1, 1986

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

By Scott B. R

Bougainville's copper mine is located on the west slope of the Crown Prince Range on Bougainville. A high grade copper concentrate is produced for sale to overseas customers. Production planning which was originally based on pilot plant data has developed progressively since commissioning of the concentrator in 1972. Pilot plant data and mine sampling have been supplanted by the correlation of concentrator performance with ore sources, as the basis for short term planning. The influence of accurate sampling is reflected in 1. hourly shift control, 2. the daily milling statement, 3. the prediction of the characteristics of ore from various mine locations, 4. production reconciliation, and 5. the control of copper losses. The mechanical and electrical failures of the original sampling system emphasized the need for a reliable, automatic sampling facility. The development of a pneumatic drive mechanism, which has now been fully field tested, was undertaken.

Jan 1, 1976

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By Brown DJ, Croghan JA, Denby B

The paper describes the development and analysis of an instability database to establish a new method of slope stability assessment for U.K. surface coal mines. The concept is based upon a Stability Index, which relates to the probability of failure of a slope. This forms the basis for a geotechnical planning software package to be incorporated into a computer aided mine design system , which is currently under development.

Jan 1, 1986

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

The known coal resources of South Australia are either of poor quality, or expensive to extract, or both. Export quality coal occurs only at great depth in the remote north of the State; the balance of the State's coal resources are suitable only for local electricity generation. Currently there is only one coal mine in the State, at Leigh Creek. This provides fuel for approximately 34% of the State's electricity generation, the balance being fuelled by natural gas. In the near future, new fuel sources must be developed to augment diminishing supplies of natural gas, and to cater for increasing demands for electricity. The South Australian Government has determined that future electricity generation will be based on the combustion of local coals. The geological and geographical environment of the known coal deposits and the quality of these coals are such that the most up to date and innovative technology must be applied to both extraction and combustion processes. The Government, the Electricity Trust of South Australia, and several Australian and overseas companies have embarked on an extensive research and development programme to ensure that these otherwise useless resources can be developed to the benefit of the State.

Jan 1, 1987

In many metal mines in China,the 70B2 series of fans has been used for main fans for a long time.These fans generate higher static pressures than are required for the relatively high equivalent orifices of the ventilation systems of many of the mines. As a consequence, their running efficiency is common only around 30%. The loss of power is significant.

Jan 1, 1988

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

By J M. Parr, C J. Yeats

Discovered in 1991 by combined plume detection and bottom-tow photography (Binns and Scott, 1993) and for some years thereafter the highest tenor mineral occurrence known on the ocean floor, the PACMANUS hydrothermal field has since been surveyed and sampled in great detail by CSIRO and international research agencies (Binns et al, 1995; Auzende, Urabe and Scientific Party, 1996; Binns et al, 2002; Tivey et al, 2006). Since 2005 commercial surveys employing deep-tow geophysical packages and remotely-operated vehicles (ROVs) have been conducted by Nautilus Minerals Inc and partners within Papua New Guinea-granted offshore exploration licenses (Nautilus Minerals Inc, 2008). Two academic drilling programs have been conducted, one under the international Ocean Drilling Program (ODP) directed at deep structure (Shipboard Scientific Party, 2002; Binns, Barriga and Miller, 2007), and one using a 5 m capable seafloor diamond drill to investigate the immediate subsurface at one site (Petersen et al, 2005). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Skinner W, Netting A. K O

Surface analysis of ore samples collected from corresponding concentrate and tailings process streams is now a widely used tool in many Australian base metal sulphide concentrators, particularly those involved in AMIRA projects. The use of tec

Jan 1, 1997

One of the features of modern life has been the increasing speed of change. We see this in many facets of activity, but in few areas more clearly than in the financial sector. The speed of communication and the advent of screen trading have made world markets one.We have titled this presentation "Cycles". It has been the conventional wisdom that Economies, Metal Prices, Equity Markets, etc. move in cycles. The objective of our presentation is to examine these cycles, to comment on the interrelationships, and to postulate where we are in The Current Cycle". We will draw conclusions as to where one should direct effort in the Mineral Scene over the next decade or so.Throughout this discussion we will use various terms to describe Time. The "Short Term" is typically meant to refer to the next six months: the "Medium Term" is one to two years; and the "Long Term" is the three to five year horizon.

Jan 1, 1990

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973