Search Documents

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The metallurgical works of the Electrolytic Zinc Company is situated on the Derwent Estuary, approximately five miles north of the city of Hobart and near a relatively dense housing area. Zinc concentrates, consisting chiefly of zinc and sulphur, have been roasted at Risdon for 53 years;- recently at rates of 1, 100 tons per day. The zinc content of the ores is converted to zinc calcine (ZnO), which is a dusty material. The calcine is leached with acid to form zinc sulphate, which is then electrolysed to make zinc. The sulphur is oxidised during roasting to sulphur dioxide, part of which is converted to sulphuric acid and part is dissolved in estuarine water which is then discharged to the Derwent Estuary. Photographic slides were exhibited showing the unaffected green flora of the nearby hills, of clear exit stacks, of green lawns, and of a w ll lrcnt nines hnlP anlf nniir.qa within the Wnrka hnnnrla_rv_

Jan 1, 1971

Comalco's Bell Bay smelter produces some 94 000 t.p.a. of primary aluminium in the form of foundry alloys, extrusion billet and rolling blocks. The extrusion billet and rolling block are produced by a process, in which molten aluminium is poured into an open ended water cooled mould of the required shape. The bottom of the mould is initially closed off by a dummy or starting block. Primary cooling takes place at the mould wall and secondary cooling is achieved by direct water sprays onto the out side shell of the product. Careful preparation of the molten alumin- ium is essential if stringent alloy specific- ation limits are to be met. Optimum casting temperature must be maintained within a narrow range and metal cleanliness is important to ensure a consistent product. Increased demands of recent years for larger product and higher standards of surface quality and dimensional control have been instrumental in forcing improvements in furn- aces, casting machines and in mould and dummy Doq,

Jan 1, 1977

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

Bakelite is fairly widely known as a suitable material for the mounting of ore specimens, concentrates and tailings for microscopical study, but has not as yet had extensive application. It is the most suitable mount for specimens which are to be held in the mechanical holder of a polishing machine, based on that described by J. W. Vanderbilt*, which is installed in the Geological Department of the Melbourne University.Bakelite products are prepared by subjecting bakelite powder to a temperature of about 1600 C. under a pressure of approximately two tons per square inch for a period of four minutes. The shape and size of the products are governed by the use of suitably constructed dies. When the concentrate or tailing is mixed with the bakelite powder, a briquette is produced which can be polished so that the opaque minerals in the sample can be examined microscopically in the same way as in a piece of solid ore. A simple machine for the construction of these briquettes has been described by Head and Slavin. It consists of a small four-pillar press in which the pressure is supplied by...

Jan 1, 1933

Traditional in situ fan flow test methods under accepted standards require determinations to be made of both static pressures and total pressures during testing. This is to determine the resultant velocity pressures, which are vital in the accurate determination of the final fan airflow. These crucial velocity pressure (Vp) determinations are normally determined using simple manometric instrumentation such as an electronic manometer or an inclined liquid filled manometer. There is relatively little noise or fluctuation in the static pressure determinations and they can be quite easily and accurately recorded. There is almost always considerable fluctuation in the velocity pressure determinations though due to the highly turbulent and irregular velocity profile normally found in such in situ installations. This velocity turbulence means that the recording of such data is subject to random human error as the observer tries to average such fluctuations mentally during the observation period. Worse than this, and in the extreme, the recording of such velocity pressure data could actually easily be misreported if, for some reason, persons chose to do so.The author has devised a field method using highly accurate quartz crystal logging barometers to objectively record these velocity pressures. The method eliminates the ability to either mistakenly or intentionally misreport these crucial velocity pressures and is carried out in parallel with the recognised methodology, so result comparisons can be drawn. As such, a far greater level of confidence can be achieved in the final flow performance results than using the traditional more subjective method. Further to this it is difficult and almost impossible to refute the results using this ancillary substantiation method.The accurate determination of fan flows due to the impost of the carbon tax has taken on much more significance given the financial impacts in Australia at this time. The methodology detailed herein can be applied equally for both fan flow compliance testing and the verification of mine airflow data for greenhouse gas emission evaluations.The paper utilises the results of one 24-point pitot traverse to demonstrate the various findings. These include the very wide range of velocity pressures, which were logged at most of the measuring stations. It also illustrates how the method is utilised and compares the results derived from both this method and the more subjective traditional method along with the benefits of logging the velocity pressure results during the testing process.CITATION:Rowland, J A, 2013. Removing some subjectivity from traditional BS 848 and ISO 5802 in situ fan flow tests, in Proceedings The Australian Mine Ventilation Conference , pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By S Brochot, M-V Durance

In many cases, current metallurgical accounting practice does not consider the errors associated with the measurements used in obtaining the metal balance. Considering all measurement errors, including errors associated at each step of the process - from sampling and analytical errors to measurement errors in circuit instrumentation, can improve the accuracy of the final metal balance - assisting in the improvement of process performance, optimisation and control.The consequences of the inclusion of measurement errors on metal balance for different circuit configurations and typical metallurgical accounting practice (two product and three product formulae) will be discussed in this paper.Examples of the tools, methodology of implementation, and periodical metal balance tasks are presented to illustrate the advantage of this approach in meeting the different requirements of each department.CITATION:Brochot, S and Durance, M-V, 2012. A new approach to metallurgical accounting, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 217-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021

By A L. Wills

Cliffs Natural Resources Pty Ltd (Cliffs) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three separate hubs and trucked to Koolyanobbing. There it is crushed and screened to lump and fines finished products and railed to Esperance port for export to Asian customers. Cliffs is renowned in the marketplace for its consistent product quality. In 2010, 9 Mt of ore was exported to Asia.Over the last three years, Cliffs has systematically refurbished its product quality system (PQS), to improve efficiency of production while maintaining its high standard of product quality. Particular attention has been given to reducing inventory, which has required significant modifications to the production process design.In redesigning the production process, emphasis was placed on maximising the application of the inherent blending in each of the production process steps and dedicated blending was only introduced where essential. Simulation modelling and statistical analysis of process capabilities were utilised to develop a system that optimises inventory, minimises rehandle, eliminates several decision-making steps and maintains a pull focus throughout the value chain.The new planning functions are now fully integrated and effectively control long-term grade variability rather than relying on long-term stockpiling. The production process design and the daily crusher blend plan are used to control short-term grade variability. With the upgrading of the planning processes the accuracy and consistency of algorithms for lump per cent and lump and fi nes grades became more important and an increased geometallurgical function has been added to the company.The continuous stockpile management system was upgraded to increase the effectiveness of the daily crusher blend planning process and is now the sole intervention point in the production process for grade-based decisions. Grade control systems were modified to utilise advances in software and geostatistics to deliver accurate short range planning models. The reconciliation and sampling systems have also been refurbished with an emphasis on practical application and feedback loops.Accountability and transparency are provided by management reports that are generated from a centralised data warehouse and the introduction of a corrective action system. Standardised reports are available to all stakeholders and a quarterly KPI scorecard assists the management review process.The successful rejuvenation of the PQS has culminated in operational efficiency through the implementation of an integrated end-to-end process flow. Shareholder value is maximised through maximising recovery of the resource and minimising costs. Customer focus is maintained by reliably delivering product with acceptable and low grade variability.

Jul 11, 2011

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R Jacobs

"The Jaguar project is relatively unique in that it was evaluated, financed, built and operated to completion within the last ten years, providing the opportunity to holistically review and reconcile expectations against the actual outcomes. It is a case study that allows wider conclusions to be drawn with respect to the risks and opportunities involved with project evaluation and execution.Jaguar is located in the Leonora Mining District of Western Australia and was commissioned in mid-2007 as an underground accessed, single high-grade volcanic-hosted massive sulfide (VHMS) deposit with an on-site concentrator, producing copper and zinc concentrates exported via the Port of Geraldton to South-East Asian markets.The feasibility study (FS) had several iterations (JML, 2005a); the last dated July 2005 was specifically targeted to secure project funding, and summarised the reserves-only portion of the resource and its planned exploitation. The commissioning of the mine was the transition for the owner Jabiru Metals NL from junior explorer to producer and the project was the dominant asset of the company.Jaguar operated through several significant deviations from the linear project plan set out in the FS, including the Global Financial Crisis (GFC), a corporate takeover and disruption to the mine plan from the onset of material geotechnical issues. Whilst the GFC or mining disruption were not specifically predicted in the FS or peer reviews, the generic effects of the events were assessed in the project risk assessment and they influenced subsequent management decisions. In parallel to the internal project-specific risks, the short planned life of Jaguar was a risk to the continuation of the corporate entity which was being addressed by significant investment into brownfields exploration to extend or replicate the project, and ultimately added value such that attracted a corporate takeover.Holistically, the project delivered the returns predicted in the FS, but in a much different guise than was expected. This paper will describe the reality of operations compared with the study predictions and expectations through the perspective of the project and corporate risk assessment.CITATION:Jacobs, R, 2016. Jaguar base metals project case study – has reality reflected the study?, in Proceedings Project Evaluation 2016, pp 86–97 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A S. Derrington

In some parts of Australia, mine air cooling may not be needed until a depth of 1300 m below surface is reached. In other locations, it may be essential at a depth of only 300 m below surface. The reasons for these differences are multifaceted. This paper discusses the main factors and describes a simple method to assess whether or not mine air cooling will be required. The method uses a graphical relationship that considers depth below surface, geothermal gradient, surface climatic conditions and directness of the mine intake routes. This relationship has been developed, tested and refined over a period of more than ten years using data collected from most of Australia’s deeper metalliferous mines. The method provides a ‘first-pass’ indication of whether more detailed cooling studies may be needed. Perhaps more importantly, the method’s underpinning by benchmarking against other mines improves confidence in the assessment results. Like any empirical method, the context must be understood and this aspect is also discussedCITATION:Derrington, A S, 2014. Will your mine require cooling?, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 181–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A G. Guinea

Every person in an organisation has what could be called ‘a different take’ on what it means to be a safety leader. The directors will tell you they are ultimately responsible for everyone’s safety and that they can be imprisoned as a consequence of a workplace fatality. Managers, take more of a focused approach and would explain that they are totally responsible for the safety of their teams. And then there are front-line leaders. Those that not only have the responsibility (like directors and managers) but they also have the accountability, and the ability, to influence how safely their teams work. But it is not just physical safety that leaders should be concerned with.

May 5, 2022

The production of synthetic rutile from ilmenite using hydrochloric acid leaching is investigated. Previously published data is used to comment on the optimum process conditions. It is shown that the most important aspect to consider is the maximisation of impurity dissolution and the minimisation of titanium losses.

Jan 1, 2001

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J M. Wallis

Heavy mineral sand exploration drilling prior to the 1970s generally utilised open hole auger and air-blast type drilling. However, mining reconciliations were poor and limitations on accuracy and precision of drilling results were severe.Working with the exploration companies, Wallis Drilling principals designed various systems, including what was termed the ‘Eneabba System’ and then the ‘Capel Twin-Tube System’. Eventually the company with its improvements developed and patented the Aircore Drilling System.Aircore drilling has subsequently become recognised as an excellent drilling system for exploration and mine-sample drilling that gives good precision and accuracy in sampling both above and below water. Its use has also been extended to many other commodities and is used in a number of overseas countries.This paper documents anecdotally the development of the system, identifying problems encountered during the times it was evolving and of the means to overcome the problems as being the documentation of the story by the inventors and developers in Wallis Drilling Company. Aircore drilling system is a Western Australian technological development owing its existence to the designing and incorporation of a number of discrete improvements along the way and recognises the tenacity and inventiveness of all who contributed to the system, in both Wallis and also in a number of companies that gave the impetus to succeed.

Oct 5, 2011

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021