Search Documents

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Fowler

The unpredictability of the location, grade and width of narrow-vein deposits presents difficulties for mine geologists and engineers attempting to estimate, schedule, forecast and mine their deposit profitably. This unpredictability stems not only from the grade distribution within a vein, but also the irregularity of vein geometry in three-dimensional (3D) space. Traditional deterministic methods of modelling vein geometry do not account for the inherent variability of the veins, resulting in significant errors when using limited drill hole information. This paper presents a probabilistic method of modelling narrow-vein deposits using sequential gaussian simulation (SGS), which can quantify this variability and improve production forecasts. Vein geometry, thickness and grade are simulated to provide a number of different equi-probable realisations that each honour the drill hole and face sample input statistics. An example is presented from the Augusta narrow-vein Au-Sb mine in central Victoria, where the simulation results are validated against the input data and survey pick-ups of the veins along ore drives.

Aug 22, 2011

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By D R. Seaman, Y Peng, F Burns, D J. Bradshaw

Telfer Gold Mine is a gold-copper mine in the eastern Pilbara of Western Australia, owned and operated by Newcrest Mining Limited. TelferÆs ores are processed by a dual train, 21 Mt/a, concentrator where gold is primarily recovered by gravity concentration and the flotation of a gold-bearing copper concentrate. A minor portion of TelferÆs gold is also recovered to a pyrite concentrate that undergoes treatment via carbon-in-leach (CIL) cyanidation. The gold recovery of the CIL circuit is below the industry standard and operates with a high reagent consumption rate.With a new fine-grinding facility, the Telfer process plant will have the ability to liberate copper and gold from the pyrite concentrate and recover these by flotation prior to the existing leaching circuit. This process will improve overall gold and copper extraction, while reducing reagent consumption in the CIL circuit.This article is an overview of the development of this methodology. Size-by-size analysis and mineralogical studies of monthly composites identified factors limiting the CIL gold recovery and the causes of high reagent consumption. Laboratory studies confirmed a relationship between the regrind product size and gold leach recovery. The addition of an intermediate flotation stage ensured that the regrind circuit will improve overall recovery while at the same time reducing operating costs. Without the addition of a flotation stage, the additional reagent consumption from regrinding alone would be prohibitive towards increasing recovery. Pilot scale studies confirmed the conditions required to selectively recover gold and copper from the pyrite concentrate as well as establishing the full scale regrinding energy requirements. Construction of this facility at Telfer is currently underway.CITATION:Burns, F, Seaman, D R, Peng, Y and Bradshaw, D J, 2012. Development of a pyrite regrind circuit at Telfer Gold Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 45-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By E C. Holloway

"The financial valuation of mining assets has a number of fundamental differences to the valuation of many other asset groupings. One such difference is that typically, the greater proportion of both the cost and revenue sides of the cash flow are inherently governed by systemic market forces.As a result, the range of outcomes for the valuation of each mining asset is more unpredictable, with higher levels of risk and uncertainty. In contrast, the management function of many other non-mining businesses or industry groups can control at least a portion of the cash flow by maintaining the margin or controlling the sales price. The management teams of mining businesses and operations typically have limited options, and are thus price-takers for both costs and revenues. As mining is an inherently cyclical industry, large, long-life operations can exist through several price cycles, making valuation both subjective and challenging.The outcomes of both static- and stochastic-based valuations, as well as the internal probabilities of the associated cash flow statements, are significantly impacted when the correlations between the appropriate parameters are quantified, modelled and incorporated into the valuation framework. The appropriate parameters for correlation modelling primarily include those that are governed by systemic market forces. Applying this process results in a different risk profile for the asset by allowing the risks resulting from systemic market movements to be more accurately quantified and then objectively minimised. This process also reduces the level of residual uncertainty in the valuation outcome.This paper presents a valuation methodology to pragmatically incorporate this level of valuation sophistication and statistically quantify the associated increase in the level of confidence of the valuation outcomes reported.CITATION:Holloway, E C, 2016. Correlated valuation methodology, in Proceedings Project Evaluation 2016, pp 181–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

THE Company's smelting equipment consists of three blast furnaces, supplied with blast from two sets of vertical piston blowers, each capable of delivering 8000 cub. ft. of air per minute at a pressure of 60 oz. per sq. in. Each blower is belt-driven by a 1:30 h.p. motor. The maximum speed of the blowing engine is 35 r.p.m.No. 1, the largest of the three blast furnaces, has a crucible area of 49.5 sq. ft., and measures 11 ft. 6 in. x 5 ft. at the tuyeres.From tapping floor to feed floor measures 35 ft. 9 in., and holds, when full, 100 tons of charge. Blast enters through thirteen 3-m. tuyeres at 60-oz. pressure. Working normally, this furnace is capable of treating :300 tons of charge, exclusive of returned slag and coke, per 24: hours, with an output of 100 tons of lead. Tapped slag flows into a C.l. forehearth mounted on wheels, where any lead and matte is caught, and the slag overflows into a 3-ton cast-iron pot, in which it is drawn away by an electric locomotive and poured over the dump.

Jan 1, 1918

By Kyle J. H, Misra V. N

The recovery of copper from a flotation concentrate using ferric chloride leaching has been investigated. The concentrate from the Horseshoe Lights Mine near Meekatharra, Western Australia, contained mainly digenite, pyrite and talc minerals. Over 95 per cent of the copper was dissolved in an acidified ferric chloride solution in one hour at 70¦C and ambient pressure. The pyrite and gangue minerals did not react. The leaching process was found to consist of four separate reactions and the shrinking core model was used to describe the process. The effects of particle size, temperature, concentration of FeCls, stirring speed and leaching time on metal dissolution were investigated. The apparent activation energies in the second, third and fourth reactions of leaching of copper concentrate were 28.8, 11.9 and 53.9 kJ/mol, respectively. The optimum conditions for the leaching of copper from the concentrate, within the range of conditions studied were: particle size 63 per cent minus 38 ¦m, a ferric chloride concentration of 1.48 M, a temperature of 70¦C, and a stirring speed of 800 rpm.

Jan 1, 1991

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Galli

Traditionally pit optimisation and scheduling is carried out assuming that the resources, the commodity prices and production costs are all known. Once the pit contour and the mining schedule have been determined, geostatistical simulations can be used to assess the impact of the uncertainty in the resources on the pit design and the schedule, and likewise stochastic simulations can be used to test its robustness to fluctuations in costs and prices. But it would be more interesting to have a dynamic procedure for optimising the pit as the resources become better known and as economic factors such as commodity prices and costs evolve over time. This paper presents a novel approach for doing this. Rather than working with millions of small selective mining units, it was decided to work with large blocks, called macro-blocks. Mining sequences are defined as the quantities to be extracted from each macro-block in each time period. Feasible mining sequences are mining sequences that respect the accessibility constraints, and also the geometric constraints on the amounts that can be extracted from any one block over time, or from all the active blocks at a given time. Having defined feasible mining sequences, their mathematical properties were studied. It was found that natural breakpoints occur in the sequences when one set of blocks have been completely mined out, thereby opening up access to others. It was discovered that families of sequences exist, and that they are convex and closed under certain types of row permutation operations. Convexity is an advantage when optimising. The closure property opens up the possibility of mixing and matching subsequences of rows in the sequences. Another interesting property is that the sequences form branching families, rather like the binomial and trinomial trees used to model prices in finance and in real options.It is easy to generate large numbers of feasible mining sequences randomly. A two-step procedure is used to find the best one (or the best few) using three economic criteria: expected NPV,the probability of a negative NPV, and the percentage of years when the cash flow is negative. The procedure was tested on a synthetic gold mine based on the characteristics of the Essakane mine in Burkina Faso. The results were encouraging.

Sep 26, 2011

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L S. Shekhawat, M P. Roy, R K. Paswan, P K. Singh, A Joshi

Blasting in the mining industry is being transformed, and can no longer be treated as an art or a practice purely dependent upon experiences of individuals. Examples of key drivers that have demanded consistent and more accurate blast results are initiatives to control pit-wall damage to help mine steeper pit slope angles, to control damage to underground opening operating in close vicinity of the open pit mine. Such situation exists at Rampura Agucha open pit lead zinc mine, which is producing 5.7 Mt/a of ore and has started its underground part, which is slated to produce initially 2–2.4 Mt/a and 4.5 Mt/a in the near future. The open pit mine is currently working at 326 m depth and is designed to reach 421 m deep. It has been planned to operate the underground mine maintaining 50 m parting from the planned ultimate level of the open pit mine.Presently, open pit and underground mines are being operated simultaneously. The present average depth of underground working lies between 370 and 410 m below the surface level. Sometimes explosives up to 95 978 kg are being detonated in a blast round in open pit mine. These blasts are often apprehended as a danger to the safety and stability of underground openings. It was decided to document the impact of open pit blasting in the openings of underground workings, so that preventive measures may be taken for the safety and long-term stability of the underground mine. The impact of 86 open pit blasts has been documented in the underground openings and 258 blast vibration data has been recorded. The vibrations were recorded simultaneously in the roof, side walls and at floor levels. The highest levels of vibrations were recorded in the roof and the lowest levels at the corresponding floor levels. The pillars experienced lower level of vibrations than the roof. Blast designs were optimised at open pit mine to control vibration in view of long-term safety and stability of the underground openings. The vibrations generated due to detonation of explosives with shock tubes and electronic delay detonators have been recorded in underground openings for comparative assessment. Ground vibration recorded at roof, pillar and floor were analysed separately and threshold value of the vibration for the safety of underground workings has been determined based on the rock mass rating of the roof rock.CITATION:Singh, P K, Roy, M P, Paswan, R K, Shekhawat, L S and Joshi, A, 2015. Protection of underground mine structures due to adjoining open pit mine blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 279–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S J. Schafrik, Z Agioutantis, E C. Jong, K Luxbacher

Real-time monitoring of mine operating parameters is available at most mines. However, access to these data for an individual operation is typically underutilised by mine managers and technical personnel. Such monitoring systems are typically designed to provide data streams and alarms to a responsible person, but they are not utilised to extract underlying trends or correlate different data groups. Furthermore, multiple monitoring systems are usually implemented at a given site without interconnection between vendors’ systems or connection to any central management, and mine personnel are only exposed to a minimal subset of such data. Thus, it is not easy to analyse and correlate individual data streams and generate information to enhance day-to-day operational decision-making and improve safety and efficiency.This paper addresses the primary challenges associated with centralising data management and effecting greater utilisation of the vast amount of collected data, while at the same time reducing the time and effort required to manage such large data sets. Furthermore, it presents the conceptual design of a database application that can organise, present and analyse data collected by multiple sensors in different environments. The database is designed to operate in a passive manner so that active mine data management systems are not impacted. An example is given where this database is used for managing atmospheric data collected at an underground coalmine operation in the US. These techniques have a universal application and can be incorporated in a wide range of mining and construction projects.CITATION:Agioutantis, Z, Schafrik, S J, Jong, E C, Luxbacher, K and Karmis, M, 2015. A platform for managing and analysing atmospheric data in underground coalmines, in Proceedings Third International Future Mining Conference, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015