Search Documents

By Q Wang

Net present value (NPV) has been the main criterion in mining project evaluation and production plan optimisation. It is a common practice in NPV calculations to take into account only the tangible cost items in the corporate accounting system. The costs incurred due to damage to the local ecosystem and environment are left out and treated as externalities. Such practice on the one hand underestimates the total cost of a mining operation and, on the other hand, ignores the difference in ecological/environmental impacts between different mine plan alternatives. This paper attempts to measure the ecological costs of mining and to incorporate such costs into the evaluation scheme in mining project evaluation and mine planning. The ecological costs of mining are estimated based on the areas and types of land (eg forest land, grazing land, crop land) damaged by mining activities and the carbon emission from fossil fuel consumption. For the land areas (and their associated ecosystems) directly damaged by mining activities, the ecological costs are measured by the prevention and restoration costs, the lost values of eco-services of the damaged land, including bio-product production, soil erosion control, water run-off control, oxygen release, air pollutant absorption and formation of soil nutrients. The ecological cost of carbon emission from the energy consumption of a mining operation is measured by the cost of cultivating the equivalent forest land required to uptake the emitted carbon. A case study on a large-scale open pit mining project is presented to demonstrate the influence of ecological costs on the mine planning outcome.

Sep 26, 2011

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

About 74% of global seismic energy release occurs in the Circum-Pacific zone. Worldwide, about 71% of seismic energy release is in the form of shallow earthquakes, 27% as intermediate, and 2% as deep earthquakes. Seismic energy release is variable in time and has been shown to correlate with the amplitude of the Chandler wobble. It was high during the period 1949 to 1967, and is now at a rather low level, with the latest earthquake over M = 8.0 having taken place in Indonesia in 1971. The average worldwide recurrence rate for the expected largest magnitude earthquake (M "9.5) has been estimated as several tens of years, in marked contrast to the several tens of thousands to hundreds of thousands of years separating the largest volcanic eruptions. Geological studies are needed to establish reliable mean intervals between large earthquakes, and to detect the e;:istence of long-term fluctuations in the ste of occurrence. Seismic gaps have proved seful in static forecasting of large earthquakes, by identifying places where closer study of the variation with time of seismicity, deformation, and other parameters, may lead to the dynamic p_ediction of time, place and magnitude of earthquakes. The model of stress concentration at asperities explains the main features of seismicity in the Circum-Pacific. Slow earthquakes have been detected instrumentally, notably an event immediately preceding the 22 May 1960 Chile earthquake, the largest this century. It seems likely that this type of deformation may explain both instrumentally detected and macroscopically observed pre-seismic deformation, as well as unusual animal behaviour reported before some earthquakes. Seismic and volcanic events are interdependent, with large earthquakes commonly triggering eruptions. Melting of rock and intrusion of magma is likely to accompany many earthquakes.

Jan 1, 1987

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979

By D Q. Zhu

In this paper, the pretreatment of concentrates by roller press was present to improve the granulation of blends comprising some 30 per cent iron ore concentrates and enhance the sintering performance. It is shown that by pretreatment of fine concentrates through roller press, the content of +3 mm fractions of granulation mixture and sinter mixture permeability are elevated by ten per cent and 35 per cent. In the meantime, a sinter productivity increase from 1.51 - 1.62 t.m-2.h-1 is attainted in pot tests with similar sinter tumble index and at lower coke rate. The mechanism of the pretreatment of concentrates process to improve sintering performance of fine iron ore concentrates was demonstrated by mineralogy that better permeability help form more calcium ferrite and good microstructure of sinter, further proven by the better metallurgical performance of sinter.

Jul 11, 2011

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

By M Badawi, Y Foucaud, C Veloso, J Laine, A C. Araujo

Iron is one of the most exchanged commodities worldwide. Its use for steelmaking explains the growing demand in the metal which remains mainly produced by the mining and the beneficiation of iron ores. Flotation is the most used mineral separation technique worldwide, processing several billion tonnes (Bt) of ore annually, including, in some cases, hematite and magnetite ores. Based on the physicalchemical properties of mineral surfaces, flotation aims to selectively adsorb molecules that render mineral surfaces either hydrophobic or hydrophilic, known as collectors and depressants, respectively. Hydrophobic particles are then recovered in the froth by the injection of gas bubbles travelling up in the cell and attaching the hydrophobic particles. However, despite the popularity and the good performances of flotation, mining industry faces new challenges of decreasing grades and increased mineralogical complexness in ores. Many flotation variables, especially when related to reagent adsorption, remain poorly understood and it becomes necessary to gain knowledge to enhance the existing processes. Molecular modelling techniques like the density functional theory or molecular dynamics simulations (ie Classical molecular dynamics or Ab initio Molecular Dynamics) currently represent powerful tools for different applications in material sciences, like catalysis or depollution purposes. They have recently been successfully applied in the flotation area, with an increasing number of publications dealing with this topic every year. These tools provide crucial information on bulk and surface properties as well as on the adsorption mechanisms of reagents on mineral surfaces, key step in the flotation process, and synergetic effect of collector mixtures. A better understanding of the adsorption mechanisms of flotation reagents, provided by molecular simulations, will help to finely choose flotation reagents, and even lead to the development of new reagents formulations. Overall, these tools enable the discovery of practical and industrial solutions to improve the flotation process, which will undoubtedly help the mining industry to face its future challenges.

Nov 8, 2021

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

By F Rashidinejad

Iran has had an active mining sector for some 7000 years. Exceptional in terms of its mineral diversity, Iran produces 62 minerals, and is ranked among the world’s 15 most mineral-rich countries. Many people around the world know Iran as one of the major petroleum exporters. Oil and natural gas dominate Iran’s economy, and oil exports provide the principal source of income, contributing more than 80 per cent of foreign exchange earnings. Transformation of Iran from an oil exporter to an independent country to oil has been on the table for many years, even before the Islamic Revolution of 1979. Development of the Iran’s mineral industry is one of the major replacements for petroleum exports. In the last decade, Iran invested billion dollars in the mining and mineral industry sectors and to increase the added value, tried to export processed minerals instead of the raw materials. In accordance with the ‘20-year Perspective 2025’ that targeted by the Supreme Leader, Iran will be a country with the first rank in economy, science and technology in its region. The objectives over this perspective include briefly increasing annual production to 55 Mt of crude steel, 800 000 tonne of copper cathode, 1.5 Mt of aluminium, 200 Mt mineral products, 300 000 tonne of zinc and 5 000 kg of gold. These goals are achievable in normal circumstances, but concurrency of the 20-year Perspective 2025 with commencement of the UN Security Council sanctions against Iran, frustrated objectives of the perspective, at least the ones related to the mining and mineral industry sectors. This paper tries to elaborate the development programs and following challenges for the mining activities of Iran by 2025.

Nov 22, 2011

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By P Ring, B Cooper, C Carr, G Laing

The Nova Ni-Cu-Co Operation, located in the Fraser Range of Western Australia, commenced commercial production in July 2017 only five years after discovery. Owned by Independence Group NL (IGO), the operation has successfully ramped up over an accelerated schedule and currently deploying leading technologies. This paper begins with a description of the Nova Operation, and its journey to achieve full production in such a short time frame. It includes discussions on development and production design, selection of fixed plant infrastructure, and the features challenges of running a low-pressure primary ventilation circuit. The paper also discusses key technologies that have improved overall safety for the underground workforce, and improved operational efficiencies. Investigations continue into the implementation of further technological applications for safety and productivity enhancements. This paper also discusses the findings from a study into transitioning from a diesel to an all-electric underground mining fleet, based on a review of Nova if it were to be developed today with the current EV offerings. The study indicates compelling savings will be available to future mines when considering development design, project schedule, capital outlay and operational savings, and the ‘next Nova’ is expected to be all electric.

Mar 15, 2021

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

By Y Cui, G Cao, H Zong, J Zheng, J Wang, S Yue, J Zhao, B Li

The iron (Fe) concentration in nickel slag is high, making its recovery and utilisation a hot and challenging topic. In the nickel smelting process, using CaO instead of SiO2 to adjust slag’s composition, and then directly reducing Fe from the output of molten slag is a more feasible method in practice for Fe recovery in nickel slag. The adjustment of slag’s composition in the nickel smelting process will have an impact on the distribution of impurity elements such as Pb, Zn, and As. In this paper, the slag adjustment of nickel smelting process was carried out with the oxygen-enriched topblowing system. The distribution of impurity elements in the smelting products with each composition slag was conducted by using thermodynamic software. Experimental verification was performed with rich oxygen top-blowing, and the distribution characteristics of impurity elements in the smelting products were characterised to explore the differences in mineral phases of impurity elements with each smelting conditions, elucidating the distribution patterns of Pb, Zn, and As in each phase. The results indicate that after slag adjustment, impurity elements are more easily to volatilisation and removal into the gas, reducing their total concentration in slag and matte. In the slag, the existence form of Pb, Zn is changed from silicate to ferrate, and As is changed from arsenate to low-valent arsenic oxide. It is easier to decompose the impurity-containing mineral phase and remove the impurity elements in the subsequent iron extraction process.

Jun 19, 2024

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The state of sampling practice in South African minerals industry must be appreciated in the context of the changes that the country has recently lived through. These include the entrepreneurship and investment in local mineral developments, the 'unbundling of mineral assets', the rising foreign control of South Africa's mineral assets, developments in the regulatory environment, and the training that has come to the industry through international experts. In terms of their financial contribution the five most important commodities in the South African mining industry include gold, platinum, non-ferrous metals, ferrous metals, and coal. International Organization for Standardization (ISO) standards form the basis for international trade in two of these commodities and have had a steadying influence on sampling practice over the years. The contribution of the minerals industry to the economic well-being of South Africa and the strong financial links between good sampling practice and minerals marketing, has acted as a driver for improved sampling practice. The state of sampling practice at mining operations of the five main commodities was found to be quite widely divergent with 'pockets of sampling excellence' in each of the commodities. The stages of mineral development at mines for each of the commodities have been described in terms of the sampling sites, sampling mechanisms, and associated problems at different stages of mineral production from exploration, through face sampling, blasthole sampling, and in-mine grade control, ore processing and handling, metallurgical subsampling, process subsampling, and subsampling in the laboratory. In each case the principal errors were identified and their potential impact on value erosion was estimated. In the final analysis it is evident that the greatest problems arise in the early stage of mineral development, and that ferrous metals and coal are particularly susceptible to loss of value through poor sampling practice. Several examples of value lost through poor sampling at the marketing stage that arise from breaching contract specifications, either in terms of grade or sizing, are described. The conclusion is that larger companies with larger ore deposits and greater human, financial, and capital resources are probably more compliant with 'best sampling practice' than smaller companies. Finally the message that equipment suppliers are sending is that business is booming and the awakened awareness of the issues around sampling practice are translating into rands and cents spent on improved sampling equipment.

Mar 1, 2010

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By S M. Gover

Estimating the probability of failure for embankments is not intuitive. It requires not only an appreciation of the strength of the embankment, but an understanding of the variability and uncertainty in the strength parameters as well. These additional aspects are, in themselves, relatively new to most practicing engineers, and therefore require some discussion.This paper discusses the concepts of probability and uncertainty, and presents a reliability-based numerical experiment, together with a literary study and collation of some of the author’s historical slope stability analyses, to investigate whether a direct relationship between safety factors and probabilities of failure exists for certain levels of uncertainty in strength parameters. In doing so, a useful tool is presented whereby knowing the safety factor of a simple slope or embankment with a consistent level of uncertainty, one can infer an approximate probability of failure.CITATION:Gover, S M, 2018. Linking safety factor to probability of failure, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 384–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018