Search Documents

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

By Moorrees C, Koh P. T, Tsambourakis G

Calcination of samples from the Savage River region of Thsmania containing varying magnesite/dolomite ratios under conditions optimized for the magnesite component, followed by carbonic acid leaching at elevated pressures, leads to leachates of varying composition. For a 3 per cent solids slurry leached at 15.5°C and 700 k Pa carbon dioxide, the leachates have magnesium concentrations in the range 0.71 - 13.2 g/litre. The corresponding magnesium extraction data are 12.5 - 86.4 per cent. The variation in leachate composition would be unacceptable in terms of continuous processing, so that a feed of "constant" composition is essential. Selective mining and physical beneficiation to remove the bulk of the dolomite do not appear to be practical. It is concluded that the most appropriate method of feed preparation is to carry out extensive blending of the magnesite/dolomite ore and the resultant calcine.

Jan 1, 1987

The following paper deals with a method for the" Proximate Analysis" of Chloridized Ores, which are free from arsenic, antimony and lime. When these are present the analysis is rendered far more complicated, and many of the methods which I am about to describe could not be applied. Sufficient scope is therefore offered for discussing the analysis, when these metals are present, in a separate paper, which I hope to contribute at a future date.I am fully aware that this method is far from being perfect. No doubt many, modifications and improvements will suggest themselves to my readers, and I trust that this paper will be the means of giving a certain impetus to the study of Proximate Analysis which at the present time is practically dormant. For the benefit of my readers who are not initiated into the details of ordinary estimations, I have briefly described well known methods, which, however, will be found fully described in most text-books of analysis. Assuming that the ore contains. sulphates and chlorides of soda and magnesia, sulphates, sulphides, chlorides and oxides of copper, lead, iron, zinc, manganese and silver chloride, the analysis would be conducted as follows. The first compounds to estimate are the chlorides and sulphates of soda and magnesia.

Jan 1, 1901

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

The copper-clay deposits consist largely of goethite and clayey mudstones carrying native copper, cuprite, and chalcocite. The mudstones are of Ordovician age, are interbedded with Fe-Mn carbonates, and probably contained syngenetic iron and copper sulphides. The secondary copper minerals have been derived from post-Devonian weathering in situ and also by deposition from surfaee and underground waters draining the adjacent mineralized volcanic rocks.

Jan 1, 1969

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

The ultraviolet spectrum of isopropyl ethylthionocarbamate (the principal constituent of Dow flotation collector Z-200) in water and of Z-200 itself in water was found to have an absorption peak at 242 nanometers(nm). The height of this peak was found to be directly proportional to isopropyl ethylthionocarbamate concentrations up to 15 p.p.m. Z-200 contains about 90 per cent isopropyl ethylthionocarbamate and the heightof the peak was proportionately lower, but obeyed the straight line relationship up to 15 p.p.m. This showed the potential value of spectrophotometric measurements for the determination of Z-200 residuals in flotation liquors.Methyl ethyldithiocarbamate (an impurity in Z-200) increased the peak height slightly, but other impurities in Z-200, xanthates, and most inorganic salts present in flotation liquors do not interfere. However nitrate ion and thiosulphate ion have absorption peaks which overlap the isopropyl ethylthionocarbamate peak.The simplest general method to overcome this effect is to extract the isopropyl ethylthionocarbamate into cyclohexane and to measure the absorbance of the extract.The maximum absorbance of the cydohexane extract was at 247 nm and the peak height at this wavelength was found to be directly proportional to the isopropyl ethylthionocarbamate or Z-200 concentration in the original aqueous solution. An alternative method is to measure the spectrum of the original aqueous solution using the aqueous raffinate from extraction as a reference solution. This gives the spectrum due to isopropyl ethylthionocarbamate alone and measurement of the absorbance at 242 nm gives the concentration in the original aqueous solution. Both methods give the same value for the concentration of isopropyl ethylthionocarbamate in the original solution.

Jan 1, 1969

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

From time to time lead, which is normally considered to be a soft ductile metal, fails by cracking. The cracks which form appear to be of two distinct types-(a) those which follow a zig-zag course around the boundaries of crystals and (b) those which follow a more direct path, frequently two systems of cracks appearing at right angles.The former appear definitely to be associated primarily with the properties of the crystal boundaries, whilst the latter appear rather to be determined by the system of stresses applied. In both cases the lead appears to be a brittle rather than a ductile metal, for the failure occurs without the large amount of deformation usually associated with the tensile breaking of lead. The latter is, however, a function of time and when lead is deformed by long applications of stress, the metal appears to- be less ductile than when the stress is applied suddenly. Thus, if a given test piece of commercial lead is broken by a stress of 1100 lb. per sq. in. in several hours, it may extend 40 to 50%before failing, whereas when broken by a stress of 500 lb. per sq. in. acting for 12 months or more it willshow an extension of only 15 to 25 %. With lower stresses still, failure would take much longer and undoubtedly lower extensions would be obtained.As the stress is lowered it is found that the marked local contraction characteristic of ductile metals becomes less noticeable, and failure, instead of being by extension of *Lecture delivered to the First 'Ordinary Meeting of the Australasian Institute of Mining and Metallurgy, 21st August, 1935.

Jan 1, 1935

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

The selection of Sydney and Port Kembla for the First Ordinary Meeting of the Institute for 1938 was, no doubt, a recognition of the celebrations marking the 150th Anniversary of the first settlement of this country. In selecting a theme for my Presidential Address, I propose to depart from the precedents of my distinguished predecessors, as I feel that this year of celebration is the natural year for a brief review of the history and progress of the Institute.In July, 1892, the Amalgamated Mining Managers' Association of Australasia held its Annual Conference in Ballarat, Victoria, when Mr. Uriah Dudley, who attended as a delegate from Broken Hill, brought forward the advisability of the formation of an Australasian Institute of Mining and Metallurgy. Mr. Dudley was authorised to take such action as he thought fit, and the result was the formation of a Provisional Committee in Broken Hill of men who were mostly members of the American Institute of Mining Engineers. Broken Hill was therefore really the birthplace of the Institute.A circular headed Broken Hill, September, 1892, with the signature of Uriah Dudley, Acting Hon. Secretary, Provisional Committee, which was sent to those likely to take an active part in the formation of an Institute, read as follows:-The Mining Managers' Association of Australasia has suggested that the time has now arrived when an Australasian Institute of Mining Engineers should be established, having objects similar to the American Institute, of which all of the Thirty-one Colonial...

Jan 1, 1938

By D Brett

The Paper presents the authors thoughts on how the mining industry should be improving the education of site personnel so they can provide a greater level of effective control of tailings dam safety including empowerment to develop their own documentation, monitoring and surveillance systems and to better liaise with specialist external technical staff or consultants.

Jul 1, 2021

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

Your Excellency, on behalf of the Council of the Australasian Institute of Mining and Metallurgy, and, indeed, on behalf of everyone present, I extend to you a welcome, and our thanks for your gracious acceptance of the invitation to be here to-day and, later on, to present Honorary Membership Certificates. I also welcome the several official representatives of our Allies, of Great Britain and our sister Dominions.To Messrs. E. C. Driffield and E. J. Rigby, two of the original Foundation Members, who are with us to-day, I extend greetings.The present occasion is opportune to express, on behalf of a representative body of professional men, deep appreciation of the sacrifice which His Majesty the King has made, and will continue to make, by appointing His Royal Highness the Duke of Gloucester as Governor General of Australia and, therefore, His Majesty's senior personal representative in this country.I suppose, that as the primary reason for our assembly to-day is to celebrate the Fiftieth Year of the Institute's existence, I should properly on this occasion, give an account of its history and development. However, as this subject was ably covered by Mr. L. V. Waterhouse, in his Presidential Address in 1938, I trust I may be excused for selecting some other subject. I shall, therefore, exercise my privilege as President and give you a short history of the Mining and Metallurgical Industry of this country with special reference to its effect on the development of the Commonwealth and on the national economy. I apologize in advance for any statistics which I inflict upon you; some of these will be three or four years out of date, because of censorship restrictions. I shall as far as possible refer firstly to the industry prior to and including 1893, the Institute's foundation year, and then to subsequent development.Australia, is pre-eminently a pastoral and agricultural country and it leads the world in the production of wool. Nevertheless, it has an international reputation as a producer of gold and various metals and of minetal products.The development of gold mining in the decade 1840-50 was an epoch-making event in Australia's history, because, to quote one writer's apt phrase, "it precipitated Australia into nationhood." It was certainly responsible for a rapid increase in population. Thus, during the period 1841-1861 the population of Australia increased fourfold, from 221,000 to 1,170,000.The effect of the discovery of gold in Western Australia was even more striking. In 1890 the population of that State was 49,000 and in 1900 it was 180,000.Statistics in respect of gold are reasonably complete, even for the years prior to Federation, and it is interesting to note that the gold declared as...

Jan 1, 1944