Search Documents

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,' sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.' The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By Waldemar Lindgren

THE purpose of this paper is to present certain facts relating to Cordilleran differentiation and metallization. Theoretical discussions concerning the exact modus operandi of differentiation, the causes that led up to it, and the original distribution of the magmas have been omitted because the author feels that his knowledge is deficient. These subjects have been adequately treated in the admirable works of Iddings, Daly, Harker, Tyrrell, Shand, and Wolff. The facts here set forth seem to indicate that differentiation and metallization form one continuous process during the eastward movement of the magmas, culminating in the alkaline province of the eastern border of the Cordilleran Ranges.

Jan 1, 1933

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By H. T. Clark, S. Feigenbaum

THE importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct- reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermo- chemistry of steelmaking. The problem is not merely one of making a small number of temperature measurements in the open-hearth furnace. This has been done by several methods to a degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open- hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800° to 3100°F. are encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protection of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of .brittle materials, unsuited for handling on the open-hearth floor. The lie of the equipment was short and maintenance was an important consideration. EARLIER WORK Any one of a number of physical proper- ties of liquid steel could conceivably be used as a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1946

By C. D. King

THIS year the American Institute of Mining and Metallurgical Engineers celebrates its seventy-fifth anniversary as well as the same anniversary of iron and steel in this country as we now know it. The society's span of life comprehends the very beginning and gradual development of the present-day iron and steel industry and its TRANSACTIONS are rich with the trials and achievements of the pioneers in this field. It is difficult to believe that in the first year of the Institute's existence there was produced in this country only 84,000 net tons of ingots, of which only 2000 tons was made by the open-hearth process; that the bessemer process was just barely beginning; that charcoal and anthracite were virtually the only blast-furnace fuels; that Mesabi ores had not been used in blast furnaces, and such pig iron as was then made was produced at a number of small units, each adjacent to its ore and fuel supply. The growth from 84,000 net tons production of steel ingots to 95,500,000 tons in 1945 eloquently tells the story of America's industrial growth.

Jan 1, 1947

By T. Egleston

The direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German b1oomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Notwithstanding the improvements which have been made in the constrnction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The name of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of' German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process.

Jan 1, 1880

By Thomas Fraser

There are large coal reserves in Argentina, Brazil, Chile, Colombia, Peru and Venezuela, and growing productive industries in Brazil, Chile, Peru and Colombia. The paper describes current activities in these coal fields, and improvement programs that are in progress, or are planned. Special emphasis is placed on improvements in mining and preparation practice, and expansion of production that have been accomplished by American equipment and technical assistance.

Jan 4, 1951

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,' formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery's' atomic

Jan 1, 1957

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado's intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By Robert Glass Cleland

THE MEMBERS of the Phelps-Dodge, Phelps-James co- partnership differed widely from one another in certain aspects of temperament and personality; but in one thing Anson Phelps, William Dodge, and Daniel James were fundamentally alike. They were all bred in the English Puritan tradition. Their creed, moreover, was the stern, militant, uncompromising creed of John Calvin and John Knox. The present generation, harshly intolerant of such a creed, has little understanding of the authority it exercised on the thinking and conduct of its adherents or of the contributions that those same adherents made to human welfare and social progress. The men who accepted its authority "were characterized by a blend of strong individualism and an equally strong sense of social duty, and they submitted their own souls to the same searching scrutiny that they applied to their business ledgers." To all three of the immediate founders of Phelps Dodge, their religion was the most real and important thing in life. It was with them day and night, in joy and sorrow, in loss and prosperity, in their most trivial personal affairs, in business transactions of the greatest moment. It was with

Jan 1, 1952

By L. A. Wright, H. L. McKinley

PINE Creek mine of Union Carbide Nuclear Co. is some 23 miles northwest of Bishop, Calif., in the Sierra Nevada Mts. Office and mill are 7800 ft above sea level, the 1500 level portal is at 9300 ft, the A level portal at 10,800 ft, and the 3050 portal at 11,500 ft. Original claims were located in 1916, and the mine worked intermittently until 1936, when it was purchased by Union Carbide Corp. Since then the property has been operated continuously, except for two brief periods when operations were suspended because of manpower shortages. Mine production through 1956 amounted to 2,792,425 dry tons of ore.

Jan 10, 1957

By Wheeler P. Davey, Robert T. Phelps

A study of solid solutions has long been a source of interest because of the conditions controlling their formation. X-ray investigations so far have been conducted with the idea that there were two types of solid solutions. In the first type, an atom of the solute was supposed to replace an atom of the solvent in the crystal lattice. In the second type, an atom of the solute was supposed to lie in one of the interstices between the atoms of the solvent. These pictures both require that the sizes of the atoms must play an important part in the process of solution. It is the purpose of the present investigation to study the mechanism of solid solution, using pure silver as the solvent, and pure aluminum as the solute. X-ray measurements show that these elements have the same "shape" of atomic domains1 (they both crystallize as face-centered cubes) and that their atomic diameters differ by less than one per cent.' The results of the present investigation point toward a chemical rather than a physical picture of the nature of solid solution, and make the older pictures merely special cases of a more general picture. The new theory has the advantage, too, that it offers a rational explanation of certain phenomena which hitherto have been only interesting detached facts. The aluminum-silver system which was chosen for this study has been studied by various methods by several workers. By means of thermal analysis Gautier2 and Petrenko3 have determined the phase diagram. Hansen studied the aluminum-rich alloys by means of thermal and microscopic analyses. He showed that at high temperatures silver dissolved in aluminum to the extent of 47 per cent by weight at 560" C. But this solubility decreased to 1 per cent at 200" C. Westgren and Bradley5 made an extensive X-ray study of these alloys. They used the change in the lattice parameter of silver as a criterion of the solution State College, Pa.

Jan 1, 1932

NORTH AMERICA ALASKA Anchorage.-Strandberg, H. College.-Barber, R. J. Burns, W. T. Henricksen, R. Henton, H. M. Joesting. H. R. Comet.-Albertson, F. E. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Andregg. J. N. Coats. R. R.

Jan 1, 1938

By T. R. Graham, R. G. Feustel, J. R. Long, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By Frank W. Clinard, Oleg D. Sherby

The effect of multiple an transformations on diffusion in a dilute iron alloy was studied. Inter-penetration between iron and an Fe-Co alloy was evaluated, under thermal-cycling conditions chosen so as to transform only the iron-rich side of the diffusion couple. It is shown that a small but consistent diffusion enhancement by a factor of two results when data from the transforming side of thermally cycled specimens are compared with predicted inter diffusion coefficients based on isothermal data. No enhancement is found when data from the mntransforming side of such couples are compared with predicted diffusivities. It is suggested that short-circuiting by moving pain boundaries is the most likely mechanism contributing to the observed diffusion enhancement from multiple phase transJormations in iron. Transformation-induced Point defects, dislocation-pifie short-circuiting, and point defects generated by dislocation motion are less effective in contributing to enhanced diffusion under the experimental conditions utilized. SO far as is known, no studies have been made of the effect of allotropic transformation on diffusion. previous to this investigation. Studies have been made, however, of the influence of transformation on the diffusion-controlled processes of spheroidization and sintering. Cullen1 has described a method of accelerating spheroidization in an AISI 1030 steel. Partial transformation between a and ? phases was uti-

Jan 1, 1965

By J. Bartrum, I. S. Schache, H. J. Dobrowolski

Developments in milling of silver/lead/zinc ores at Mount Isa since 1970 have followed broad objectives to improve metallurgical performance and to increase plant capacities for Mount Isa ores treated through the No. 2 Concentrator. Pilot Plant work on a range of Hilton ores has led to detailed feasibility studies on application of heavy media pre-concentration and zinc reverse cleaning techniques on Mount Isa ores. The role of these developments in achieving metallurgical goals and effects of different ore characteristics are discussed.

Jan 1, 1977

By T. F. Kassner

The dissolution kinetics of type 304 stainless steel in the Bi-Sn eutectic alloy have been investigated under the well-defined hydrodynamic conditions produced by the rotating-disc sample geometry. In addition, the mutual solubilities of iron, chromium, nickel, and manganese from 304 stainless steel in the eutectic alloy were determined over the temperature range 450" to 985°C. The convective -diffusion model for mass transport from a rotating disc was used to interpret the experinlental dissolution data. The dissolution process was found to be liquid-diffusion-controlled under specific conditions of temperature and Reynolds number. Liquid penetration into the 304 stainless steel resulted in a reduction of the di,ffusion-controlled mass flux and thus precluded the calculation of the diffusion coeficients of the four components from 304 stainless steel in the Bi-Sn eutectic alloy. The convective-diffusion model for diffusional limitations of electrode reactions and mass transport at the tationssurface of a rotating disc set forth by Levich 1,2 has found wide applicability in the investigation of electrochemical and dissolution phenomena in aqueous systems. Riddiford 3 and Rosner have reviewed the model and also include numerous references on work of this nature. More recently the rotating-disc system has been applied to the investigation of hetereogeneous reactions in liquid-metal systems. Shurygin and Kryuk 5 have measured the dissolution rates of carbon discs in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Shurygin and shantarin6 also studied the dissolution kinetics of iron, molybdenum, chromium, and tungsten, and the carbides of chromium and tungsten in Fe-C solutions with a rotating-disc sample geometry. In these systems it was possible to distinguish between diffusion and reaction control mainly through experimental confirmation of the velocity dependence of the dissolution rate predicted by the model. However in the absence of dependable solubility data and the virtual lack of diffusion data in these systems, a quantitative check of the magnitude and the temperature dependence of the rate was not possible. In many instances, estimates of the activation energy for solute diffusion and the diffusion coefficient based upon the experimental dissolution data are not credible. A recent study by this author7 has resulted in a critical test of the model in a liquid-metal system. The solution rates of tantalum discs in liquid tin were measured over a wide range of temperature and velocity conditions. In addition, the solubility and diffusion coefficient of tantalum in liquid tin were determined as a function of temperature. The latter data were used with the model to predict both the magnitude and the temperature dependence of the dissolution flux. In that work it was also deemed necessary to reevaluate the solution to the convective diffusion equation to incorporate the effect of the lower range of Schmidt numbers encountered in liquid-metal systems. Good agreement between the model and the experimental dissolution data in the region of diffusion control was obtained in the Ta-Sn system. The Bi-Sn eutectic alloy is used as a seal between the reactor head and the reactor vessel in the Experimental Breeder Reactor-11. The alloy is fused periodically prior to fuel-handling operations. In that connection, it was necessary to investigate the compatibility of the liquid alloy with the type 304 stainless-steel containment material. The results of a rotating-disc study in this multicomponent system are presented. EXPERIMENTAL METHOD The 5.08-cm-diam discs were machined from 0.317-cm-thick plate. Chemical analysis information for the type 304 SS material is given in Table I. The discs were ground flat on metallographic paper and given a final polish on Linde B abrasive. A thin support rod was threaded into the disc and the region around the threads was fused under an inert gas. The support rod was fitted with a quartz protection tube and then was attached to a supporting shaft which passed through a rotary push-pull vacuum seal. The disc and supporting shafts were dynamically balanced prior to insertion into the furnace tube. The apparatus is shown schematically in Fig. 1. The 58 pct Bi-42 pct Sn eutectic alloy melts were prepared from 99.995 pct pure Bi and Sn by fusing the components in a 7-cm-ID Pyrex crucible. The system in which the melts were made was evacuated to a pressure of 1 x 10-6 Torr and back-filled with purified argon several times before melting the charge. The ingot was reweighed and placed in a slightly larger-diameter Vycor crucible used in the dissolution runs. A run was started by lowering the disc into the liquid

Jan 1, 1968