Search Documents

By L. Kaufman

An equation is derived relating AF a", the difference in free energy between austenite and martensite, to temperature and composition in the iron-chrmnium and iron-chromium -nickel systems. This equation is used to calculate at M,for low-carbon stainless steels. A method for utilizing the energetic equations to calculate M, in stainless steels is suggested. In addition, an explanation is given for the anomalous effect of chromium in forming a y loop concurrent with the lowering of M, in iron-base alloys. It has been demonstrated that the effect of alloying elements on the Ms temperature is strongly dependent upon the influence of the alloying element on the thermodynamic properties of the y and a phases. Notwithstanding the fact that alloying elements affect the Ms temperature by changing the lattice parameters, elastic constants, and inter-facial energies of the a and y phases, their primary role is a thermodynamic one. Thermodynamic analyses have been presented for the iron-carbon'-4 and iron-nickele systems in which equations are derived for Fa and FY, the free energies of the b.c.c. (or b.c.t.) and f.c.c. phases. These equations, which can be obtained with the aid of the equilibrium diagrams, can be used to help predict the Ms vs composition curves. This paper deals with a calculation of the thermodynamic properties necessary to compute AFffLY for iron-chromium alloys. In view of the lack of direct information concerning the activity of chromium in the a and y phases of iron, the regular solution approximationa,g was utilized to bridge the gap. After the necessary equations were derived for the iron-chromium system they were used to calculate AFff— Y for stainless steels by combining them with the previous results obtained for iron-nickel alloys. The results of these calculations offer a means of rationalizing the anomalous behavior of chromium in iron-base alloys. The latter depends on the regular solution approximation in contrast to the explanation offered by zener , which is based upon the "magnetic specific heat effect." THERMODYNAMICS OF THE IRON-CHROMIUM SYSTEM If y represents the atomic fraction of chromium in an iron-chromium alloy, then the free energy of the b.c.c. phase Fa, the f.c.c. phase FY, and the difference in free energy between the f.c.c. and b.c.c. phases of the same composition are given through [3] and Fmy represent the free energies of mixing of the a and y phases; while @era -' and uFea 4Y represent the difference in free energy between f.c.c. and b.c.c. chromium and iron respectively. The values of AEFe0ff4Y in the temperature range between 0" and 900K ( .

Jan 1, 1960

By J. H. Keeler

The tensile characteristics of Zr-Fe binary alloys containing up to 5 atomic pet Fe are reported for the temperature range —195o to 500°C. A linear relation between stress at constant strain and volume fraction ZrFe2 was found. The coincidence of data from unalloyed zirconium with zero volume fraction ZrFe2 indicated little or no solid solution in IL-zirconium, in agreement with Hayes, Roberson, and O'Brien.' The absolute increase in strength due to particle strengthening, although decreasing with increasing temperature, was a greater percentage at high temperature. ZIRCONIUM is of interest for use in nuclear reactors because of its low neutron absorption, good corrosion resistance, and high melting temperature. The alloying of zirconium with iron has been considered as a means of increasing the mechanical strength of zirconium without seriously increasing the neutron absorption " over that of unalloyed zirconium. The Zr-Fe system has a eutectic at 934°C and 23.7 atomic pet Fe and a eutectoid at 800°C and 4.0 atomic pet Fe. The zirconium-rich end of this system determined by Hayes, Roberson, and O'Brien' is shown in Fig. 1. The intermetallic phase coexisting with a and ß-zirconium has been reported as Zr2Fe3,1 with a,, - 7.04A, and as ZrFe2,2 face-centered-cubic, the phase being of the MgCu, type (C-15). It was more recently agreed to be ZrFe33 and face-centered-cubic. This intermetallic phase is essentially insoluble in a-zirconium, the hexagonal-close-packed modification; and the lack of solubility makes the system particularly interesting metallurgically. The system is strengthened almost exclusively by particles of in-termetallic phase, and there is very little solid solution strengthening to complicate the analysis. The Bureau of Mines, in its survey of zirconium-base alloys,' reported the tensile properties of Zr-Fe alloys made from chloride process zirconium, induction melted in graphite crucibles, and swaged at 850°C in iron sheaths. Additional data on these ZrFe alloys were given by Hayes, Roberson, and O'Brien.' Chubb and Muehlenkamp% have recently reported the strength of Zr-Fe alloys containing up to about 1.25 atomic pet Fe. These alloys were made from crystal bar zirconium, hot worked at 820°C, annealed at 700°C, and tested both at room temperature and at 316°C. Experimental Procedure The materials used in this investigation were high purity zirconium made by the iodide process and electrolytic iron. The composition of the zirconium as obtained by spectrographic analysis and the nominal composition of the iron are given in Table I. Alloy ingots weighing 100 g were made by are-melting under argon in water-cooled copper crucibles in a multihearth furnace."

Jan 1, 1957

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By M. T. Simnad, G. Derge, Ling Yang

STUDY of diffusion in molten substances is important in at least two respects. Diffusion data, combined with thermodynamic and kinetic information, throw light on the structure of the liquid state. Moreover, a knowledge of diffusion coefficients and their temperature dependence is useful in ascertaining the controlling step in many metallurgical reactions. Although diffusion measurements have been made on a number of molten salts, slags, metals, and alloys,'-'" the results available are still limited and widely scattered, especially for the high temperature melts. It is the purpose of this investigation to establish reliable procedures for the measurement of self-diffusion coefficients in high temperature melts and to use these procedures to determine the self-diffusion coefficients of iron in molten Fe-C alloys of different carbon contents. Experimental Measurement of self-diffusion coefficients in high temperature melts is usually carried out by using one of two methods. In the first, diffusion takes place between two cylindrical samples of the same material, one of which is made radioactive. The diffusion coefficient is calculated from the radioactivity penetration curve in the solidified sample after the diffusion. In the second method, samples contained in capillaries of an inert substance are immersed in an infinite reservoir of the same material. Either the material in the capillary or that in the reservoir is made radioactive and the diffusion coefficient is calculated from the change of the radioactivity of the sample in the capillary after the diffusion. The second method is simpler because a radioactivity penetration curve is not needed for the calculation of the diffusion coefficient; however,.it is valid only when no convection has occurred in the capillary during the diffusion. A radioactivity penetration curve is therefore always useful in indicating that the required conditions for the diffusion are ful- filled. Towers and Chipman" recently studied the self-diffusion of calcium and silicon in CaO-Al,O,-SiO, melts by using the capillary method. Instead of measuring the change of the radioactivity of the sample in the capillary, they autoradiographed the sample after the diffusion and calculated the diffusion coefficient from the intensity distribution of the autoradiograph. Their method is useful when the radioactive isotopes are weak ß-emitters, but is very difficult, if not impossible, to apply to cases involving strong ß or y-emitters. For such cases, sectioning of the sample according to the method of Morgan and Kitchener' may be used for the construction of the radioactivity penetration curve. The self-diffusion of iron in molten Fe-C alloys has been studied in this manner and the experimental procedures are described as follows: The diffusion apparatus is shown schematically in Fig. 1. The bath consisted of about 200 g of an Fe-C

Jan 1, 1957

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By Craig E. Saporito

INTRODUCTION Freeport-McMoRan Inc. has been very active recently with two major discoveries and its restructuring activities. This paper describes Freeport-McMoRan's businesses, the two major mineral discoveries, and exciting opportunities within the oil and gas operations. BUSINESS ACTIVITIES Freeport-McMoRan is the largest and one of the lowest cost fully integrated U.S. phosphate fertilizer producers. It is the second largest domestic Frasch sulphur producer. Freeport- McMoRan will become the largest domestic producer of Frasch sulphur when its Main Pass Block 299 sulphur deposit reaches full production in 1993. Furthermore, it is the largest transporter of sulphur produced by others. Its oil and gas activities rank among the largest U.S. independents in terms of production and proved reserves. The copper/gold operations in Indonesia are among the world's lowest cost. When expansion operations reach full capacity levels in 1992, the Indonesian copper/gold complex will be the fifth largest copper operation in the world. Operations are divided into three business segments that include: 1. Agricultural minerals, incorporating sulphur, phosphate rock and phosphate fertilizer activities; 2. Energy, including oil and gas activities; and 3. Metals, incorporating copper, gold and silver operations in Indonesia. In early 1989, Freeport-McMoRan announced the discovery of two world-class ore bodies; a sulphur deposit off the coast of Louisiana on Main Pass Block 299, and a copper/gold deposit -- the Grasberg in Indonesia -- approximately two miles away from the existing Ertsberg East operations. As a result of these major discoveries, Freeport- McMoRan decided to carry out a restructuring program. Its purpose was to sell $1.2 to $1.5 billion of non-strategic assets. Debt levels and associated interest expenses will be significantly reduced, and general and administrative expenses will be reduced, which will place Freeport- McMoRan in an excellent position to fund the development of the Main Pass Block 299 sulphur discovery, the Grasberg discovery, and oil and gas discoveries. This restructuring program also will allow Freeport-McMoRan to achieve the greatest future value for shareholders by focusing on its principal businesses (Figure 1). Strategic Restructuring • Sell $1.2 - $1.5 Billion Of Non-Strategic Assets • Significantly Reduce Debt • Significantly Reduce G&A • Fund Development Of Main Pass & Grasberg • Stronger Company; Positioned For Future Growth • Focus Is On Principal Businesses: - Sulphur/Phosphate Fertilizers - Indonesian Copper/Gold - Oil And Natural Gas Figure 1 - Strategic Restructuring AGRICULTURAL MINERALS Main Pass Block 299 Discovery The Main Pass Block 299 discovery has a proven reserve of 67 million long tons of recoverable sulphur. This is the largest known Frasch sulphur deposit in North America. The discovery increased Freeport-McMoRan's sulphur reserves more than five-fold, and is synergistic with the company's phosphate fertilizer assets. The

Jan 1, 1990

By O. Cuscoleca

The Austrian plants at Donawitz and Linz were the first to blow steel with high purity oxygen. The paper shows how the process was developed and gives a survey of the results achieved to date. Compared with open hearth steel of equal quality, the obvious advantages of oxygen steel are the low investment and conversion costs. The nitrogen content of oxygen steel is not higher than that of good open hearth steel. Rimmed and killed steel products made by the oxygen process are superior to rimmed and killed steel products made by the best open hearth process. TWO new steel plants using the principle of making steel with high purity oxygen went into operation in Austria, one at Linz (Vereinigte oster-reichische Stahlwerke) in November 1952 and the other at Donawitz (dsterreichisch-Alpine Montan-gesellschaft) in May 1953. An estimated 330,000 metric tons were produced by the two plants in 1953, the first year of operation. In 1954 production by Austrian plants- using the high purity oxygen approach will be raised to 450,000 metric tons. This will be in addition to facilities in Huckingen (Man-nesmann A. G., Düsseldorf, Germany), those planned and under construction at Hamilton, Ontario, Canada (Dominion Foundries and Steel, Ltd.), and elsewhere. It is expected that by 1955 a total capacity of one million tons of high purity oxygen steel will be available. At the close of the last century, because of increasing availability of scrap, open hearth steel production forged ahead at an ever increasing pace. This caused world steel production to rise faster than pig iron production and finally to overtake it. In 1911 65 million tons of steel were produced against 64 million tons of pig iron. World steel production was 209 million tons in 1951, while pig iron output was only 147 million tons. The 1951 breakdown for steel shows 118 million tons made from pig iron, while the balance, 91 million tons or 44 pct of the total tonnage of steel produced, was made from scrap. This increase in crude steel production on a basis of high scrap consumption led to the world market scrap shortage and soaring scrap prices. In the United States and other nations, production of converter steel has fallen far behind that of open hearth steel. The surplus of processing scrap, un-absorbable by converting mills and thus a welcome source for open hearth and electric melting shops in the past, together with regular scrap purchases, no longer can meet requirements of both open hearth and electric steel production in Europe. In addition, recent modification of the basic bessemer process, blowing with oxygenated blast, substantially raised the scrap capacity of these plants. Any further expansion of world steel production will necessitate utilization of self-containing processes in regard to scrap because of the shortage.

Jan 1, 1955

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By N. Tiner

In an article on magnesium and its alloys, Gann and Winston! stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 675°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I). This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of, these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing 0.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C. and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. Experimental Method The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

Discussion of the paper of G. K. Burgess and J. J. Crowe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2537 to 2591. HENRY M. Howe, New York, N. Y. :-I think we can hardly rate the importance of the entry of the Bureau of Standards into our field. There is no body in the world that is better fitted to undertake this work than that Bureau, and it is work which really calls for the aid of some national organization. The skill and care with which this work has been done speaks for itself. It is very striking that within a very few months the distinguished English investigator, Professor Carpenter, of whom I spoke before, thought that he had disproved the existence of beta iron by proving that the A2 retardation which Professor Burgess has now demonstrated did not occur. Dr. Burgess's demonstration of the existence of. this retardation makes the existence of beta iron very probable, in my opinion. Osmond used to call beta iron " decipuum." You knew of its existence as you know of the existence of certain planets, only by the perturbation which it caused. Certain phenomena could not be explained, except by assuming the existence of a third allotropic form, beta iron. The evidence that you got was always evasive and susceptible of other explanations, except that which we have to-day, which it seems to me is not capable of other explanation. Professor Carpenter proceeded in the same way that Dr. Burgess has, by taking the heating and cooling curves of exceedingly pure iron, and thought that he had shown that there was no thermal change, no absorption or evolution of heat at the supposed A2 point, and hence that the A2 point did not exist. This he did by a piece of reasoning which I think seems to most of us rather surprising. That is to say, if of ten witnesses, three have seen a thing and seven have not, the evidence of the seven who have not is set aside, and that of the three who have seen stands. In Dr. Carpenter's own experiments under certain conditions he found the A2 change, the heat evolution., under certain others he did not. That is like the three witnesses who saw and the seven who did not see. You can arrange your test so that this change will not become visible or so that it is masked. But though an existent change can be masked a non-existent one cannot be shown. So that the reasoning seemed to me wholly fallacious.

Jan 12, 1913

By P. van Meurs

This paper describes a technique which permits visual observation of oil displacement processes througlrout the interior of a porous structure as thick as 2 in. A model having glass walls is filled with finely powdered glass. Such a model becomes completely transparent if the powdered glass pack is saturated with an oil having the same refractive index as the glass. When water or gar, with a refractive index different from that of the oil (glass) is injected, the model becomes opaque in the space occupied by the water (gar). visual observation and photography of these displacement processes are thus rendered possible. The following processes have been studied: (I) displacement of oil by water (linear drive) in a homo-geneous formation and in a stratified formation, (2) water flooding (five-spot well pattern), (3) solution gas-drive process, and (4) oil-bank formation. INTRODUCTION Most of the scaled model experiments heretofore carried out in the Koninklijke/Shell Laboratorium, Amsterdam, have been done in steel containers, in which oil-saturated sand packs represented the oil-bearing formation. In such experiments, for instance those on the displacement of oil by water, the cumulative oil production was measured as a function of the cumulative water injection. In order to interpret the measured production data, a need has for some time been felt for a means of observing visually what happens in the course of such experiments. Some information of this kind was obtained earlier by observing the water-oil distribution in various cross sections of the sand after the conclusion of the experiment.' However, the technique used did not guarantee that the fluid distribution remained undisturbed. Moreover, the procedure was somewhat elaborate and the information obtained limited. Therefore a new technique has been developed, which is described below. DESCRIPTION OF EXPERIMENTAL TECHNIQUE AND APPARATUS Glass models simulating part of an oil reservoir are filled with ground Pyrex glass of a specific grain size, representing the porous structure of the prototype. Before an experiment is started, the porous formation has to be saturated completely with an oil having exactly the same refractive index as the Pyrex glass powder. All light-scattering surfaces of the glass grains become invisible and the formation is then transparent. If the oil is displaced by another fluid (e.g. by water in a water-drive experiment, or by gas liberated from the oil in a solution gas-drive experiment) the formation becomes opaque in the region where the oil is expelled from the rock.* The back of the apparatus is painted black and illumination is from the front; therefore, in the photographs of the experiments, the oil-bearing formation appears black, whereas the water- or gas-invaded areas are white.

Jan 1, 1958

By Edward C. J. Urban

The nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than 10 years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini- tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. Development of Rock DriI,I.s Thc earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its Piston-Type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1949

By John T. Eash

DURING the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin, 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. SELECTION OF COMPOSITION While the final criterion of the suitability of an alloy for a bearing must 0f course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstructure, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig. I. In addition, the tin bronze contains the hard alpha + delta eutectoid constituent distributed through-

Jan 1, 1945

By Paul F. Fulton, Robert K. Estes

INTRODUCTION Relative permeabilities are factual data necessary to any prediction of reservoir production behavior. One important problem in determining relative permeabilities of porous media to gas is the effect of gas slippage on these determinations. Since certain aspects of the slippage phenomenon still remain unknown, this study is particularly concerned with that problem. The validity of the theory of gas slippage as it is applied to the flow of gas through porous media has been well established. 1,2,3 Therefore, in determining the permeabilities of porous media to gas by ordinary laboratory procedure, i.e., at atmospheric pressure, the slippage correction should be considered. Rose3 performed experiments on gas relative permeabilities which indicated that the effect of gas slippage on the measured effective gas permeabilities at various liquid saturations decreased with an increase in liquid saturation. Following Rose, it was substantiated experimentally' that the effective gas permeabilities at the various liquid saturations extrapolated to infinite mean pressure were the same as the non-wetting liquid permeabilities at the same saturations. This same paper also presented data which showed that the magnitude of the slippage between those values of gas effective permeability determined at atmospheric pressure and those found by extrapolation to infinite mean pressure decreased with an increase in liquid saturation. However, these experiments were not performed at liquid saturations above 30 per cent. Therefore, the purpose of this experimental work was to determine the effect of gas slippage on permeability measurements at liquid saturations in excesh of 30 per cent. APPARATUS Five core samples were used In this work: two synthetic Alundum samples (A-1, and A-2). a Nichols Buff sandstone sample (NB-13), and two samples from producing formations, a Soso sandstone (S-1), and a vugu-lar dolomitic limestone (R-7). The core samples ranged in permeability from 32 to 663 md. These cores were chosen because they represented a fairly wide range of permeabilities and probably a considerable difference in pore size and pore size distribution. Fig. 1 is a schematic diagram of the apparatus which consists of an air dehydration filter A, two Moore null-matic sub-pressure regulators B and C, the differential oil manometer D, the core holder E, the flowmeter F, the soap reservoir G, and a mercury manometer H measuring the downstream pressure. The interesting features of the apparatus are the two Moore vacuum-pressure regulators. The regulators permit the rapid establishment and easy control during flow at sub-atmospheric pressures of both the differential and downstream pressures, and prevent the surging action of the vacuum pump from disturbing the system during flow. Provided there are no leaks in the system, these regulators will maintain without measurable change selected downstream and differential pressure. Specifically, regulator B controls the downstream pressure and regulator C controls the differential pressure. In opera-

Jan 1, 1957

By Edward C. J. Urban

THE nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than to years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini¬tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. DEVELOPMENT OF ROCK DRILLS The earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its piston-type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1947

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.' Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962