Search Documents

By Sylvain J. Pirson

The number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpretative techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method discussed here is being used actively in the Mid-Continent region and endeavors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter. The New Method Field Technique.—In sectionized territory where country roads are available every mile, shot points are preferably located every 1/4 mile when six detectors are available or every % mile when eight detectors are at hand. The disposition of individual spreads is represented on Fig. I; in each case a shot point is located at the section corners. Fig. 2a represents the layout of a spread between shot points, the vibration detectors being preferably equidistantly located. Normally in the 1/4-mile control, the distance between shot points is 1320 ft. and the distance between detectors 220 ft. When shooting from shot point S.P. I, detectors 1 to 6 are connected to the recording galvanometers and detector 0 (which indicates the vertical travel time of the wave corre-

Jan 1, 1940

By Sylvain J. Pirson

The number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpretative techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method discussed here is being used actively in the Mid-Continent region and endeavors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter. The New Method Field Technique.—In sectionized territory where country roads are available every mile, shot points are preferably located every 1/4 mile when six detectors are available or every % mile when eight detectors are at hand. The disposition of individual spreads is represented on Fig. I; in each case a shot point is located at the section corners. Fig. 2a represents the layout of a spread between shot points, the vibration detectors being preferably equidistantly located. Normally in the 1/4-mile control, the distance between shot points is 1320 ft. and the distance between detectors 220 ft. When shooting from shot point S.P. I, detectors 1 to 6 are connected to the recording galvanometers and detector 0 (which indicates the vertical travel time of the wave corre-

Jan 1, 1940

By Charles L. Mantell, P. P. Napolitano

High-purity tellurium oJ semiconductor grade may be prepared by a combination of electrowinning from tellurium oxide, electrorefining and controlled atmosphere melting, as detailed in the paper. SEMICONDUCTOR devices such as transistors and rectifiers depend upon extremely pure forms of silicon, germanium, and selenium. Although tellurium is chemically related to these elements, it has not been studied as a semiconductor because commercial forms are too impure. Highly purified tellurium would be an interesting starting point for a study of its solid-state characteristics. Tellurium shows a greater electrical conductivity in the direction of the helices or chains forming the crystals than at right angles to the chains, and thus is a semiconductor. Unlike selenium, the conductivity is only slightly increased by exposure to light. Impurities such as Ag, Cu, Au, Fe, Sn, As, Sb, Bi, Br, and I provide accepters and make extrinsic tellurium of the P type. So far, however, no elements have been found which, when introduced, would act as donors. Small amounts of tellurium dioxide enormously increase the thermoelectric power. Many extremely pure metals have been made by electrolytic refining or electrowinning procedures. Tellurium forms compounds in a number of valences, as indicated in Table I. The physical properties given in Table II do not show any unusual conditions which would interfere with the formation of elec- trodes, or the deposition of the metal on a cathode. Tellurium dioxide could be obtained in relatively high purities of 98 pct TeO2 or better at reasonable prices. Tellurium dioxide is soluble in caustic to form tellurites, which are conductive, ionizable, and from which tellurium metal may be deposited at a cathode. Preliminary solubility tests to saturation of tellurium dioxide in approximately 10 pct sodium hydroxide gave the results of Table III. The temperature range is a practical one for electroplating. Electrochemical test facilities were set up and these met the operating conditions of Table IV. For a determination of purity of deposits, there was available a Jarrell Ash Co. quantitative emission

Jan 1, 1964

By Marcel Daly

(A contribution to the study of the conditions of equilibrium of the "free surface" of a water body inclosed in a porous medium.) IN a recent paper, on Geologic Structure in the Cushing Oil and Gas Field, Oklahoma,1 Carl H. Beal has pointed out some interesting peculiarities in the distribution of the hydrocarbons and the disposition of the "planes of separation" between the oil and the water (water surfaces). Mr. Beal's principal statements on this matter may be summarized as follows: I. In every important dome in the Cushing field, which has not been complicated by folding along its sides, the oil area in each, of the three oil and gas sands studied (Layton, Wheeler and Bartlesville) apparently extends farther down on the long axis. of the dome than it does on the steeper sides. The result is that water is encountered at a lesser depth below datum plane (sea level) on the steep sides of the dome than along the ends where the beds are more gently tilted. II. In the Layton and Wheeler sands (to which the detailed study of water surfaces has been almost entirely confined), the water surface is not level, but dips at a gentle angle (maximum dip 100 ft. to the mile) away from the center of the structure. This inclination existed prior to development, and it has been rendered greater by the rapid extraction .of oil and gas. To these statements, the following observations are added. The dominant structural feature in the Cushing field is a broad north and south anticlinal fold, along whose, axis the domes are distributed (Fig. 1, p. 1104), and the more important oil areas in each sand lie on the west side of the field. In many cases, gas has been forced to the east side of the structure, sometimes as far as the water line. From the distribution of the oil and gas bodies, Mr. Beal concludes that the hydrocarbons in this region probably migrated from the west or the northwest.

Jan 1, 1918

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By R. W. Raymond

AT the Pittsburg meeting of the Institute, in March, 1910, the death of Mr. Metcalf was announced, and Col. H. P. Bope, of Pittsburg, delivered in memory of him a brief but eloquent address, which, though expressing the sorrow of Mr. Metcalf's friends, and, in general terms,. the debt of gratitude which his country and his profession owed to him, was not intended to be a complete survey of his life and work. With Colonel Bope's permission, and with the aid of some of the statements in his address, I substitute for it, in our Transactions, this more detailed, yet still inadequate memorial. As Colonel Bope justly remarked, the men who could do justice to this theme-such men, as Jones, Chalfant, Bennett, Oliver, and Park-passed away before Metcalf, leaving him almost the last of the generation of great steel-makers who made Pittsburg the Sheffield of America, and who discharged a double function, as the rear-guard of the old metallurgical practice and the van-guard of the new. I knew many of them; would that I were better qualified to celebrate their achievements. William Metcalf was born Sept. 3, 1838, at Pittsburg, Pa., where his father, Orlando Metcalf, was an eminent member of the bar. At the age, of sixteen, he entered the Rensselaer Polytechnic Institute, at Troy, N. Y., from which he was graduated in June, 1858. Returning to his native city, he became an assistant engineer in the Fort Pitt Foundry, of which. he was made Superintendent in 1859. This famous establishment produced the largest castings and heaviest machinery then known in the United States;-and Mr. Metcalf's intense, intelligent and incessant study of his business prepared him as a manufacturer for a patriotic service to his country more valuable than, as a soldier, he could have rendered in the field. The call came in 1862, when the government needed, above all things, a supply of field, naval and siege artillery. The

Apr 1, 1911

By Mary Louise Theodore, R. G. Aspden, D. A. Colling

T RACES of sulfur have a marked influence on the physical and mechanical properties of many iron-base alloys. The commonly used combustion method for the determination of sulfur content is not accurate enough at the 50 ppm level by weight and below to be useful in determining the influence of sulfur. Kriege and Wolfe' have described a method for the determination of sulfur in iron alloys in which the sulfur is evolved as hydrogen sulfide followed by reaction with N, N-dimethyl-p-phenylenediamine, and iron (111) to form methylene blue which is measured spectrophoto-metrically. This method of determining sulfur has been used to study the activity of sulfur in Fe-Si-S alloys,' but has not been previously applied to the determination of sulfur in Fe-Ni alloys because of the insolubility of nickel in dilute hydrochloric acid. Dissolution of nickel in dilute hydrochloric acid, however, can be greatly accelerated by the addition of a small amount of platinic chloride.3 By combining these two techniques in a procedure in which 0.005 pct platinic chloride in 1:l hydrochloric acid is used as the dissolving fect on the strength of the material. However, ductility is influenced by the presence of discontinuous precipitation. In Fig. 5, percent elongation data at room temperature and 1400°F is shown for two sets of specimens of Waspalloy which were solution heat treated at 1950°F and either quenched or slow cooled to the aging temperature and then aged for 100 hr at 1292" and 1598ºF, respectively. At room temperature the existence of a discontinuous precipitation cell at grain boundaries (see data point marked by arrow) has no apparent effect on ductility. However, at elevated temperatures a pronounced lowering of ductility occurs when discontinuous precipitation has occurred in the specimen. It would appear that the morphology of discontinuous precipitation "cells" at grain boundaries would be highly conducive to the initiation of cracks which in turn lead to premature "grain boundary" failure.

Jan 1, 1970

By A. S. Yue

Small-angle tilt boundaries have been observed in a lamellar eutectic structure. These boundaries are morphologically similar to a theoretical till boundary originally proposed by Burgers. The production of a small-angle tilt boundary in the lamellar eutectic structure is attributed to the formation of an indentation on a planar solid-liquid interface during growth. Constitutional supercooling due to the accumulation of impurity atoms ahead of the interface is primarily responsible for the generation of an indentation. The distance between two faults of like sign, designated as lamellar fault distance, is calculated by the Burgers equation for small-angle boundaries. It was found that the lamellar fault distance decreases exponentially and the tilt angle increases exponentially with freezing rate. SMALL-ANGLE tilt boundaries have been observed in many crystals in the as-grown states by etching techniques. However, a detailed substantial proof for revealing the presence of dislocations in the form of etch-pits was recently accomplished by Vogel. These boundaries are described as an array of dislocations of like sign. The angle of tilt associated with a boundary is treated theoretically by Burgers3 and is given by 0 = b/D for small tilt-angle where b is the Burgers vector of the dislocations and D is their average spacing. During the course of experimentation on the solidi fication of the lamellar Mg-32 wt pct Al eutectic a microstructure which was strikingly similar to a dislocation tilt boundary was observed. An example of the type of microstructure is given in Fig. 1, which shows a combination of transverse and top sections of the lamellar eutectic structure. The lamellae of the top section on one side of the apparent tilt angle are not parallel with those on the other side. Consequently, some lamellae must be terminated somewhere. Fig. 1 shows that the termination of lamellae is analogous to a dislocation tilt boundary in a crystal lattice originally proposed by Burgers. This work represents a closer look at such structures. The factors governing the production of the small-angle tilt boundary are discussed in terms of the freezing condition and impurity distribution in the melt. The effect of freezing rate on the distance between two faults, designated as lamellar fault distance, and the tilt angle is also described. In addition, the lamellar fault distance is determined by means of the Burgers equation for small-angle tilt boundary. EXPERIMENTAL PROCEDURE The slightly impure Mg-32 wt pct Al eutectic rods, 5/8 in. in diam and 12 in. long, were made from 99.99 wt pct Al and 99.98 wt pct Mg and were cast in a high-purity graphite mold. Some of these rods were purified by zone-refining the eutectic using direct-radiation helical-coil furnaces5 A molten zone about 2 in. long was passed through the cast rods at a speed of 5.3 x 104 cm per sec for ten passes of the molten zone. Before the freezing experiment was begun, 2-1/2 in. of the material from the head and tail ends of the zone-refined eutectic were removed from the rod to eliminate any impurity. The freezing experiments were carried out under controlled conditions,8 using a protective atmosphere of purified argon. At the end of each run, observation of the tilt boundary was made throughout the entire length of the rod with a light microscope on the top, longitudinal, and transverse sections (three mutually perpendicular sections) of the lamellar eutectic solid. The experimental data used for the determination of interlamellar spacing and tilt angle were taken from the middle portion of

Jan 1, 1964

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged: R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders' Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1951

By H. A. Deans

A three-parameter mathematical model for one-dimensional flow in porous media is developed. The objective of the model is to predict accurately the longitudinal dispersion associated with the flow of either gases or liquids over a wide range of Reynolds number. A qualitative analysis of the model parameters is given. Published experimental pulse-response curves are compared with results predicted by the model. Several general types of problems are given for which the model can be used. INTRODUCTION The problem of multicomponent single-phase flow through porous media is encountered in the study of petroleum reservoirs, gas chromatographic and ion-exchange columns, industrial fixed-bed con-tacters and elsewhere. These particular examples span the wide range of flow conditions possible; Reynolds numbers of less than l0-4 are not unusual in oil-production problems, while values in excess of 103 are common in large fixed-bed operations. The study of flow-dependent transport phenomena is complicated both by the changes in the character of the flow over this range, and by the irregularity of the flow boundaries inherent to porous media. Dispersion is one of the important phenomena known to depend fundamentally on flow conditions as well as on fluid and medium properties. As used in this paper, the term "dispersion" refers to the observed mixing of fluid elements of different composition which occurs in flow systems. The actual mechanism may be one or more of a number listed below. Only dispersion in the direction of the mean flow (referred to as axial or longitudinal dispersion, or mixing) is considered here, although lateral dispersion arises as part of certain coupled mechanisms. MECHANISMS FOR LONGITUDINAL DISPERSION A number of distinct mechanisms are known3,5,7,8 to contribute to the phenomenon of longitudinal dispersion. The more important of these are as follows. 1. Molecular diffusion in the flow direction. 2. Turbulent (cell) mixing. 3. Lateral transport processes coupled with velocity and/or residence time distributions, including: (a) "Taylor" diffusion caused by the interaction of velocity profiles in individual voids with lateral molecular diffusion; (b) separation and remixing or interdiffusion of streams having different velocities around particles; and (c) the couplipg of gross velocity profiles, caused by viscous instability or inhomogeneous porosity, with lateral dispersion. 4. Finite mass-transfer rate between a porous matrix and the flowing phase, and finite diffusion rate inside elements of the porous matrix. It is a well documented fact that these mechanisms, whether acting individually or in combinations, produce essentially similar integral effects. The observed dispersion can be described approximately by solutions of the diffusion equation with a properly chosen dispersion coefficient. Necessary conditions for equivalence between dispersion and diffusion are discussed by Klinkenberg and Sjenitzer.7 Apparently these conditions are not satisfied exactly in many real systems. "Best fit" solutions of the diffusion equation often depart appreciably from measured breakthrough curves for the usual pulse- or step-forced experimental systems. In particular, pulse response curves usually show some degree of asymmetry and "tailing" which cannot be reproduced by the one-parameter diffusion model. The three-parameter model proposed herein attempts to produce these effects in a realistic manner. Asymmetry and tailing are predicted for certain sets of parameter values, while for other sets the new model agrees with the diffusion model. VELOCITY DEPENDENCE OF DISPERSION Molecular diffusion apparently controls at sufficiently low Reynolds number in both gas and liquid systems.*l3 At Re > 20, turbulent cell mixing is dominant for gases flowing at low pressure; the data of McHenry and Wilhelm8 show that the mixing cell is approximately 1 particle diameter long in random sphere packs. on the other hand, the data

By J. D. Livingston, H. E. Cline

Cu-Pb alloys in the vicinity of the monotectic composition have been directionally solidified under a high temperature gradient at rates up to 2 X l0-' cm per sec. Over a wide range of compositions, high growth rates yield a composite structure consisting of continuous rods of lead in a copper matrix. This range of compositions increases with increasing growth rate, in agreement with arguments based on the relative velocities of composite growth and the growth of copper dendrites or lead drops. The breakdown of the composite structure at slow growth rates is explained in terms of the relative interphase surface energies. The observed interrod spacings of the composite structure are large compared with the predictions of the Jackson-Hunt equations of eutectic growth. ThE directional solidification of many eutectic alloys produces fine composite structures of parallel lamellae or rods. There has been considerable interest not only in the fundamentals of this two-phase solidification process,'-3 but also in the interesting physical properties produced by such regular and aniso-tropic microstructures. Composite structures can be grown only over a limited range of composition, beyond which coarse primary dendrites of one phase appear. In organic eutec-tics, this composition range of composite structures has been shown to increase with increasing growth rate.7"10 These results were explained in terms of the relative velocities of composite (coupled) growth and dendritic growth. Although similar arguments should apply to metallic eutectics,11-13 suitable experimental results are lacking. In contrast to the work on eutectics, the directional solidification of monotectic alloys has received little attention. (The monotectic reaction is similar to the eutectic reaction, except that one of the resulting phases is a liquid, which subsequently solidifies in a separate reaction at a lower temperature.) Directional solidification of some monotectic alloys'4715 yields regular rodlike microstructures, whereas in other cases macroscopic separation of solid and liquid phases occurs.16 chadwick17 rationalized these results in terms of the probable relative magnitudes of the various interphase surface energies. A recent study of chill-cast Cu-Pb alloys18 revealed a fine rodlike microstructure in alloys near the monotectic composition. It was decided to investigate the directional solidification of such alloys, and to determine the range of composition and growth conditions yielding composite structures. The Cu-Pb system is convenient for such a study, both because it is simple metallurgically, with no compound formation and negligible solid solubilities, and because its basic properties are well-documented. Recent literature on the Cu-Pb system includes studies of bulk thermo-dynamic properties,'g surface energies,20"21 densi-ties,25 and diffusion constants.a6 A similar study of the directional solidification of Cu-Pb alloys was recently undertaken, independently, by Kamio and Oya." EXPERIMENTAL Alloys were prepared by melting 99.999 pct Cu and 99.999 pct Pb in a graphite crucible, stirring well, and pouring into a cold graphite mold. Rods 0.175 in. in diam were machined from the ingots. Alloy compositions studied ranged from 25 to 55 wt pct Pb. Samples were placed in graphite crucibles 5 in. long with 4 in. OD and 0.035-in. walls. They were melted under flowing argon in a vertical, two-zone. platinum -wound furnace. A voltage stabilizer was used to minimize fluctuations in input power. The narrow specimen diameter minimized convection. Directional solidification was achieved by driving the crucible downward into a +-in. hole in a water-cooled copper toroid. The toroid was located immediately below the narrow end zone of the furnace. The end zone was separately powered to maintain high local temperature. Therefore a high temperature gradient (approximately 300 deg per cm) was maintained in the specimen throughout the run. The crucible motion was screw-driven. and a wide range of drive speeds were available. The limited rate of heat removal caused a thermal lag in the specimens at high drive rates. However. temperature-time curves from thermocouples imbedded in a representative sample indicated that the average growth rate still approximately equaled the drive rate. Although the specimens were initially homogeneous, melting and re solidification redistributed the lead. producing composition variations of several percent along the specimen length. (During melting. lead melted first and ran down the sample surface. Rapid freezing tended to reproduce the resulting composition gr~dient, but slow freezing did not because a slow-moving interface tended to reject lead. as discussed later.) To determine local composition. ;-g samples were cut from regions exhibiting various microstructures and were chemically analyzed for lead content. Micrographs were taken on as-polished or lightly etched surfaces. Three-dimensional structure of the lead network was viewed with a scanning electron microscope after removal of some of the copper matrix with nitric acid. RESULTS Several different microstructures are observed, depending on composition and drive rate. Because melting and resolidification produced composition gradients, results are best presented in t&ms of final local composition, rather than initial or average composition. The ranges of local compositions and drive

Jan 1, 1970

By M. J. Pool

The partial molar heats of solution in liquid tin of cadmium, silver, tellurium, and zinc have been measured at 655°. 700°, and 750°K by liquid-metal solution calorimetry. Silver, cadmium, and zinc are endothermic at these temperatures while tellurium is exothermic. Only the heat of solution of silver depends on composition while all four elements show a temperature-de pendent heat of solution. The heat of solution of tellurium is constant up to 0.6 g-at. pct, becomes increasingly more exothermic, and reaches a limiting value at 1 g-at. pct Te. The limiting value has been used to calculate the heat of formation of SnTe at 750°K. The heat effects associated with the dissolution of the compounds Ag2 Te, CdTe, and ZnTe in liquid tin were measured at 750°K. These values are cotnOined with the measured hat effects at 750°Kfor silver, cadmium, tellurium, and zinc to detertrline the heats of formation of the telluride compounds. Cadmium lelluride exhibits a heat of dissolution which has a compositional dependence. THERE is a considerable amount of interest in the compounds of tellurium because of their electronic properties. Both cadmium and zinc tellurides are thermoelectric materials and considerable work has been done on their electronic properties but a limited amount of data is available on their ther-modynamic properties. This work was undertaken to elucidate the heat of formation data on cadmium and zinc telluride. Since both cadmium and zinc are in Group II it seemed to be of interest to compare the values obtained for them with the heat of formation of a Group I telluride. Silver telluride was selected for this comparison. In the course of the work it was also possible to determine the heat of formation of tin telluride and therefore to make a comparison of some of the Group I, 11, and lV tellurides with the metallic elements silver, cadmium, and tin being in the same period. There is also a great deal of interest in the energetic changes which occur upon addition of solute elements to a common solvent. This investigation provided an opportunity to study the partial molar heats of solution of silver, cadmium, tellurium, and zinc in liquid tin. The partial molar heats of solution are of theoretical interest because solute-solute interactions are a minimum in dilute solutions and application of solution models is simpli- fied. In order to complete the analysis of solute-solute and solute-solvent interactions the temperature dependence of the partial molar heats of solution was also measured. MATERIALS AND EXPERIMENTAL PROCEDURE All materials were of the highest purity available. The silver, zinc, cadmium, and tellurium were obtained from American Smelting and Refining Co. and were reported to be 99.999 pct pure. The silver telluride, zinc telluride, and cadmium telluride were obtained from Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp., and were electronic-grade material of 99.999 pct purity. Tin used for the solvent bath and for calibration was obtained from the Vulcan Manufacturing Co. and was reported as being 99.99 pct pure. The liquid-tin solution calorimeter used in this work is similar in principle to the differential twin-type calorimeter described by K1eppa.l Two of three identical calorimeter wells are used together during any set of experiments, one well being active and the other being passive. The wells are positioned 120 deg apart in an aluminum calorimeter block. Each well contains a multijunction thermopile and a Pyrex test tube to hold the liquid metal bath. Forty-eight of the thermopile junctions are distributed over the surface of each calorimeter well adjacent to the test tube and serve to integrate the heat effects occurring. The other forty-eight are next to the aluminum calorimeter block. The thermopiles for the three wells are connected differentially so that any change in temperature at the outer junctions (which will be the same for both wells because of the high conductivity of the aluminum block) will oppose for the two wells and result in no shift of the zero. The electrical output represents the true temperature difference between the two reaction vessels. A reaction occurring in the active well gives a comparison with another body of very similar thermal properties. In this way, any spurious heat effects due to slight temperature drifts within the entire calorimeter block are eliminated. The output of the differential thermopile goes to a dc amplifier with multiple ranges of from * 10 pv to 1 30 mv. The output of the amplifier is then fed into a Leeds and Northrup strip-chart recorder. The adiabatic temperature change is then calculated using the technique of Howlett, Leach, Ticknor, and ever.' The aluminum calorimeter block is contained in a cylindrical furnace with main and control heaters

Jan 1, 1965

By P. L. De Bruyn, R. J. Charles

THE transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact. Experimental Method: Longitudinal impact of a rod with a fixed end was chosen as the impact system for investigation. The rod was mounted horizontally and the fixed end was formed by butting one end of the rod against a rigidly mounted steel anvil. The rod, of pyrex glass, was 10 in. long by 1 in. diam with both ends rounded to a 6 in. radius. The rounded ends permitted reproducible impacts on the free end of the rod and assured a symmetrical fixed end. Pyrex was selected as the rod material because of the marked elastic properties of such glass and the similarity of fracture between pyrex and many materials encountered in crushing and grinding operations. The frequency of natural longitudinal oscillation of the rod was 10 kc, and thus simple electronic equipment could be used for observation of strain changes occurring in the rod at this frequency. As shown in Fig. 1, impacts on the free end of the rod were obtained either by a pendulum device or by a spring-loaded gun. Relatively heavy hammers (100 to 600 g) of mild steel were used in the pendu- lum impacts, while fairly light projectiles (20 to 80 g) were fired from the spring-loaded gun. One of the main objects of the experimental work was to obtain the strain-time history of the rod as a function of the mass and kinetic energy of the impacting hammers. For this purpose a technique involving wire resistance strain gages and a recording oscilloscope was employed. Five gages were applied at equidistant sections along the rod, and by means of a switching arrangement the strain-time history at any section, and for any impact, could be obtained in the form of an oscillograph with a time base. The equation relating strain and voltage change across a strain gage through which a constant current is flowing is as follows: e = ?v/iRF [1] ? = strain, ?v = voltage change, i = gage current, R = gage resistance, and F = gage factor (from manufacturer's data — SRA type, Baldwin Lima Corp.). With the above equation an oscillograph depicting voltage change vs time on a single trace can be converted directly to a strain-time diagram if a calibration of the vertical response on the oscilloscope screen for specific voltage inputs is available. In the present case the calibration was obtained by photographing precisely known audio frequency voltages on the same oscillograph as that on which a voltage-time trace from a strain gage had been made. Synchronization of the beginning of the single trace with the beginning of the impact was accomplished by permitting contact of the impacting objects to close an electrical circuit from which a voltage pulse, sufficient to initiate the trace, was obtained. The struck end of the rod was lightly silvered for purposes of electrical conduction so that it would form one of the electrical contacts. Markers every 100 micro-seconds on the traces served for a time base calibration. Determinations of the kinetic energies of translation prior to impact were made in the case of the pendulum hammers by measuring the height of fall of the hammer and in the case of the projectiles by measuring the exit velocity from the gun barrel by means of an electrical circuit employing light sources, slits, and phototubes.' During the experimental work it became evident that the time of contact between the impacting object and the rod was an important variable in the impact process. Measurements of the times of contact were made, therefore, for every impact for which a strain-time record was obtained. The time of contact was determined by permitting the impacting components, when in contact, to act as a closed switch and discharge a condenser at relatively constant voltage. The discharge was observed and photographed with a time base on the oscilloscope screen.

Jan 1, 1957

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows : W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged : R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders' Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1964

By Henry Louis

The present paper comprises two parts, which have but little con nection with each other. The first is practically a continuation of the investigation on the specific gravity of gold liberated by means of acids from its alloys, on which subject I had the honor of presenting a brief note to the Institute in 1893 (Trans., xxii., 117); the second describes a series of experiments on the behavior of amorphous gold under the action of heat. By the kindness of Prof. W. C. Roberts-Austen, C.B., F.R.S., chemist to the Royal Mint, I have been permitted to conduct these experiments in the mint assay-office, all the splendid resources of which institution were freely placed at my disposal. I desire at the outset to express my obligations to Prof. Roberts-Austen and to all the staff of the mint assay-office for their kind assistance at all stages of my experiments. I.—The Specific Gravity of Gold in Alloys. In the note already referred to, I published my discovery that the gold left on dissolving out the silver from an alloy of gold and silver (which I shall here term " residual amorphous gold ") has a higher specific gravity than ordinary molten gold. I also pointed out that I had worked on very small quantities of material and with balances and weights on the accuracy of which I could not implicitly rely, and that in so far my numerical data were inconclusive, although I had but little doubt of the correctness of the broad fact. The experiments now recorded were made under the most advantageous circumstances and with various refinements. Particularly, I found that the ordinary form of specific-gravity bottle was responsible for several small sources of error; and I accordingly designed an improved form (Journal of the Society of Chemical Industry, April 30,1894, vol. xiii., p. 322), which I used for this work. The

Jan 1, 1895

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.' Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.'' As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By R. S. Shoemaker

Mines are closed for two reasons; exhaustion of ore or insufficient price for the mineral. On the other hand, the reopening of an old mine can be the result of any one of three events; the discovery of more ore, a sudden rise in the price of the product or the use of a new low-cost method of mining or milling the ore. Examples of the latter would be the open-pitting of an orebody previously mined underground as recently happened at Tyrone, N.M., or the adoption of acid leaching of an old pit as has been done at Miami, Ariz. The unique native copper mines of the Keweenaw Peninsula of upper Michigan have not been so fortunate. These deposits, which were first worked by prehistoric Indians, have been mined continuously from the early 1840's to 1968 when the last mines of Calumet and Hecla were closed and the Ahmeek mill. still using eight Nordberg steam stamps, was shut down. There are two types of deposits from which native copper is obtained; amygdaloid, which is a lava flow, and conglomerate, a sedimentary deposit of sand, rock fragments and pebbles cemented together. "In the amygdaloid, the copper is disseminated, or distributed much like the raisins in a cake; but in the rich Calumet conglomerate, the copper is more like a malleable rope or thread cementing the pebbles together." (C. Harry Benedict. Red Metal: The Calumet and Hecla Story, (Ann Arbor, Michigan, 1952), p. 42.) These deposits produced almost all of the copper used by the North in the Civil War and were substantial contributors to the copper needs of the United States in both World Wars. Some were mined to depths of as much as 9500 ft along the dip of the vein structure and 7500 ft vertically. Few of the mines ever really became worked out, but became uneconomical because of depth, pinching of veins or grades which dropped to about 1%.

Jan 5, 1972

By Franklin R. Carpenter, W. P. Headden

TWO notes have already appeared in the Transactions concerning the columbite or tantalite of the Black Hills tin-mines. In vol. xiii., page 232, Prof. Schaeffer speaks of the mineral as tantalite, and concludes by saying that its separation from the tinstone "is a matter which will, I believe, prove puzzling to the wisest metallurgist." He also observes that he is unable to find by analysis in his specimens the least trace of columbic acid. Prof. W. P. Blake, in the same volume, at page 696, says: " Even if it [tantalite or columbite] were present to a considerable amount, it would not injure the tin in smelting. It does not alloy with tin, but carries a small percentage of tin, which would probably be liberated in smelting." He calls the mineral columbite from the fact that a great number of specificgravity tests invariably indicated that it should be so classed. We have made chemical tests as well as specific-gravity tests upon many samples from many different parts of the Hills. Our analyses have always shown the presence of columbic acid, and the specificgravity tests have always indicated columbite, as we have elsewhere shown.* As Prof. Blake has already observed, it is not found in such close association with the tin as to prevent separation by a rough handsorting, but it is usually present with the stream-tin. As Prof. Schaeffer says, it cannot be separated by ordinary concentration; and while, as declared by Prof. Blake, its columbic acid may not unite with the tin in any form, yet its iron and manganese oxides may be reduced, and thus lower the quality of the tin produced, as is also the case when the smelting charge contains wolfram. To determine the effect of columbite in the ordinary potassium cyanide assay, there were assayed at the Dakota School of Mines four samples containing different proportions of columbite. The results, published in the report of the school for 1888, seemed to indi-

Jan 1, 1889