Search Documents

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By A. M. McQueen

Activity in the oil industry in Peru was somewhat above normal in 1928. Probably the most significant feature was the interest displayed in the oriental region in the northeast part of the country (Fig. 1). This region, though little known, has long been considered potentially rich in oil! gold, coal and other minerals, lacking only transportation to make it the country's most valuable source of income. The Standard Oil Co. of New Jersey, through its recently formed subsidiary the Standard Oil Co. of Peru, has acquired various tracts along the Maranon and Ucayali rivers in the neighborhood of the Brazilian border. Standard Oil Co. interests have had geological and surveying parties in this part of Peru since 1921, and as a result of the work done, we understand they have under lease at the present time some 2,500,000 acres of prospective oil lands. Development in the coastal region continued along normal lines during the past year. Production figures for both the International Petroleum Co. and Lobitos Oilfields show a small increase over the last few years. Total production figures since 1924 for the International Petroleum, Lobitos Oilfields and Zorritos companies, only in a minor degree estimated, are as follows: 1924, 7,924,700 bbl.; 1925, 9,138,042 bbl.; 1926, 10,750,676 bbl.; 1927, 10,110,696 bbl., and 1928, 11,969,677 barrels. International Petroleum Co., Ltd. Operations on the La Brea-Parinas Estate during 1928 continued with satisfactory results; nearly all branches showing improvement over the previous year. The average daily production for 1928 was 25,966 bbl., compared with 21,282 bbl. for 1927, an increase of 22 per cent. During the last two or three years, production methods on the company's property have been improved in line with the advance in scientific technique throughout the oil fields of the United States. Extensive investments were made in compressor equipment for handling surplus gas with the result that the gas-lift and repressuring operations are in no small way responsible for the increase in the 1928 production. In addition, the company's three casinghead plants produced 24,847,708 gal. of gasoline compared with 17,240,865 gal. in the previous year.

Jan 1, 1929

By Sid T. Killan

The utilization of the reducing power of blast-furnace gas can be estimated by applying two rectifying calculations to the gas analysis. A resulting corrected CO/CO2 ratio varies inversely with furnace production. Directions for calculating the corrected CO/CO2 ratio are given, and a corrected CO/CO2 ratio is compared with actual furnace production. THE inadequacy of the normally accepted CO/CO, ratio as a measure of blast-furnace performance and furnace efficiency was discussed following the presentation of the paper by H. F. Dobscha.' In this outstanding example of careful observation on large scale blast-furnace operation, the changes occurring with beneficiated ores were: 1—A net gain in tonnage of 21.2 pct. 2—A decrease in net coke of 15.3 pct. 3—A decrease of 1.9 pct in the CO/CO, ratio. In this great change in furnace performance, the CO/CO, ratio proved itself worthless. The discussion of the inadequacy of expressing furnace performance and efficiency by the CO/CO, ratio led indirectly to the calculations forming the basis of this paper. At that time Dr. T. L. Joseph said: "We must consider difference in CO, from the stone in the two cases when we talk about the ratios of CO/C02." This statement is used for the second of the two CO/CO, ratio corrections forming the basis of this paper. The research work in attempting to find out why the furnaces could op-erate so differently with practically the same CO/CO, ratio lead not to the answer sought but, after a shift to the gaseous phase in the research work, the proof that the normal CO/ CO, ratio was outmoded and a new corrected ratio should replace it. To be of any value, any new corrected ratio should express approximate furnace efficiency and give an idea of practical furnace performance to be expected. This the normal CO/CO, ratio has failed to do. However, in the absence of anything better, some credence has been attached to the normal CO/CO, ratio. As far as the writer can ascertain, the present paper is the first attempt to change or improve the normally accepted index of

Jan 1, 1952

By L. O. Howard

The practice of using acid-lined converters at the plant of the Old Dominion, Copper Mining & Smelting Co. was discontinued early in January, 1913, and replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyeres. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the 'converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyeres must wait until such time as a slight falling off in.the matte supply allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter. The first 12-ft. shell was blown in on Jan. 6, 1913, and ran until June 27, 1913, when it was removed to patch the brick. A record of operations covering this period follows: Shell No. 1. First Campaign, Jan. 6,to June 27, 1913 Commenced blowing............................Jan. 6, 1913. Taken off stand for patching.....................June 27, 1913. Total blowing time..........................2,689 hr. 40 min. Total number of, blows made.............................. 664 Average time of blow............................ 4 hr. 3 min. Tons matte charged.................................. 18,157 Average copper content of matte................ 43.9 per cent. Average time blowing one ton. copper................ 22.5 min. Total copper made............................... 7,250 tons

Jan 1, 1915

By L. Adler

Analysis of a mine roof can be based on fixed-end beam behavior. The author here analyzes the effects of zero restraint at deflecting beam supports. Formulae are given for determining permissible support deflections. Analysis of a mine roof in a bedded deposit usually follows the assumption that the behavior of the roof is analogous to a beam with both ends fixed. Yet it is recognized that the end restraint itself varies with the thickness of cover, so that at shallow depth the restraint is minimum, and at great depth, maximum.' Consequently, an analysis on the basis of fixed ends or full restraint represents only one extreme in the possible range of conditions. Since the actual amount of restraint is difficult to ascertain, a more rational approach is to consider the two extreme cases of end restraint. Such situations regarding uncertainty of the restraining effects of supports are not uncommon in structural analysis, and are handled in a like manner.' Since previous studies9)4 have dealt with full restraint, this paper will analyze the effects of zero restraint at deflecting beam supports. In such a case a mine roof with several intermediate supports becomes analogous to a uniformly loaded continuous beam on simple supports, as shown in Fig. 1A. Such a structure is statically indeterminate to a degree equal to the number of intermediate supports, n. Therefore, with the three equilibrium equations, n additional equations are needed. A number of methods exist to analyze this problem, but The Theorem of Three Moments is Simplest. The continuous beam is divided at each support into a sequence of simply supported single span beams, with the unknown end moments, as appears in Fig. 1B. Continuity requires that the common ends of adjacent beams have the same slope (Fig. 1C). eiB= B(i+l)~= ei(i+l)and MiB= Mti+I)A= Mi(i+i). [1I A Glossary of all terms is given in Table I. Furthermore, if we first consider that the supports do not deflect, the slope at a support is the sum of the slopes due to each of the individual loads shown in Fig. 2, yielding:

Jan 1, 1961

By Howard Eavenson

THE eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) is width, the hill sides slope from 25° to 33°, and the tops, from 600, to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate, the use of a large number of local pumps or of numerous drainage ditches to keep the mine free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In hew workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and. unless from three to four times as many pumps are installed as are normally needed, considerable', output is lost. In most cases the water will .flow from the mines, so the obvious solution is to provide drainage .ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places.

Jan 1, 1921

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By C. R. Sandberg, N. Stein, L. D. Wiener, E. B. Elfrink

this paper presents the results of a study of the slip velocity of gases rising through liquids in vertical tubes, inclined tubes, and vertical annuli. The data were obtained in gas-liquid systems which included combinations of air, propane and natural gas (over 97 per cent methane) with water, lubricating oils, and crude oils. The 214 data points obtained in this study along with 11 data points reported in the literature are incorporated in an empirical correlation which relates the mean slip velocity of gases flowing through liquids with the parameters gas rate, tube size, ratio of liquid viscosity to liquid density, gas density, liquid density, and the angle of the tube from the vertical. The average numerical deviation of the measured slip velocity data from values obtained from the correlation is 9.2 per cent. The average algebraic deviation between measured and Predicted data is 0.31 per cent, an indication that the correlation is a satisfactory representation of the data. The correlation presented in this paper will be useful primarily in the design of subsurface gas-oil separation equipment for increasing the efficiency of oil-well pumping installations. but may perhaps be extended to other situations of gases rising through liquid columns. INTRODUCTION The production of oil by pumping is often complicated by the presence of free and dissolved gas in the oil at bottom-hole conditions. This gas can be drawn into the pump barrel and result in "vapor locking" the pump, thus reducing the efficiency of the pumping operation. Large amounts of free gas may be excluded from the pump by the use of a gas-anchor, which is designed to allow the separation of free gas from the oil before it is drawn into the pump. The design of a suitable gas-anchor depends on a knowledge of the difference between the velocity of the free gas and that of the oil as the oil travels down toward the pump intake. This rate of gas rise through the oil is termed "slip velocity." AS a first step toward the full understanding of this roblem, the mean slip velocities of gases flowing through static

Jan 1, 1952

By C. W. Mason

TIN has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphur. The notorious "tin disease," which Cohen1 has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white 0 tin to cubic gray a tin, has apparently encouraged the expectation that one or more addi-tional polymorphic modifications might exist. The search for confirma-tion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but for previous assumptions. The ball apparently was started rolling in 1880 by Trechmann,' who reported a new modification of tin (y tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be y tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller.3 Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,6 by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) and stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencer3 in 1921 examined the above evidence critically; he found similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on a second lot of crystals, not described crystallographically.)

Jan 1, 1939

By R. E. J. Putman

Introduction Self-tuning regulators are a class of controllers built around the concepts of sampled data theory, and are especially suitable for implementation in a digital microprocessor or minicomputer control system. The algorithms used are distinctly different from those based upon analog control techniques and include automatic adjustment features which permit them to adapt to unmeasured changes (in, for example, ore grindability) or process nonlinearities (as exhibited by cyclone classifiers). They are also designed to handle transport lags in a simple manner, for example, anticipating the effects of a variable recycle rate on particle size distribution. The advent of distributed control systems will encourage the exploration of these techniques in the minerals processing industries, and particularly for improving the control of comminution circuits, which are especially energy intensive. This paper outlines some current work in progress on this topic. Background Those engaged in the practice of process control have long had two philosophical problems for which solutions have been actively sought - what is optimal control and how can we attain it in some heuristic fashion automatically. The basic analog controller can be represented by the differential equation: [V = Ko + K1 f y • dt + K2 dt(1)] where: v and y are the instantaneous values of output and error respectively and K0, K1, and K2 are tuning constants. The empirical rules for establishing the values of K0, K1, and K2, which provide stability, have evolved from the initial suggestions of Ziegler and Nichols(9) in 1942 and have served their purpose well. However, later analyses demonstrated that there are in fact many combinations of the values of K0, K1, and K2 which, besides being stable, behave better or worse in relation to other process control criteria; some examples are duration of error, amplitude of a damped response, magnitude or rate of movement of control valve or adjustment of speed regulator, etc. The definition of optimality had broadened. In 1964, Kalman(4) published his classic paper which tried to resolve these problems. He defined a

Jan 1, 1982

By B. E. Parsons

Curtailment of production of crude oil, to the extent of effecting an approximate balance in supply and demand, was a problem confronting the oil industry in California throughout the year 1930. At the beginning of the year, with drilling operations only slightly checked, the California industry faced a steadily increasing potential production, an actual production in excess of market requirements and stocks of crude oil and refined products which had reached staggering proportions. During the year, the intensive development of the Playa Del Rey field and extensions to several oil fields, together with flush production from numerous large wells from both new and old fields, caused a steady increase in the state's potential production to a record peak in November of 1,186,000 bbl. daily. Despite the burden of this steady stream of flush production and the handicap of incomplete cooperation in several fields, curtailment successfully lowered the trend of crude oil production in California, except for the period of an open-flow test to determine actual potential production in several important fields in February. Under the curtailment programs in effect, the state's production of crude oil for the year was reduced 22 per cent. under the production of 1929 and even slightly under the production for the years 1927 and 1928. The total stocks of crude oil and refined products were reduced 2.7 per cent. during 1930, as compared to an increase of 30 per cent. in total stocks of all products during 1929. Drilling operations were reduced 28 per cent. as compared to drilling activities during 1929. Voluntary curtailment of drilling programs by many operators, particularly the major companies, accounts for the greatest portion of the reduction in drilling activity. The decline in drilling activity at Santa Fe Springs and in the east-side fields of the San Joaquin Valley was more than offset by development in new fields and extensions to deeper zones of old fields. There were 755 new wells completed during 1930, as compared to 910 completions in 1929. At the close of the year, 220 wells were drilling in the oil fields of California, 9 of which were being drilled in search of deeper producing horizons.

Jan 1, 1931

By H. M. Wilson

The relation of labor to the accident rate in mines is admirably epitomized by Thomas T. Read in his paper presented at the St. Louis meeting, in the sentence "Reliance for accident prevention must be upon the individual worker himself." In connection with the inspection of mines for the fixing of merit premium rates for insurance under workmen's compensation, it has been the practice of The Associated Companies to allow 60 per cent, of the credits for safeguarding of the physical hazards of the mine and 40 per cent. for the human element. By "human element" is meant that inherent tendency of the industrial worker to be careless, negligent, or disobedient, in respect to his own safety, and after that also of his fellow workman. This is a tendency not only of the laborer or of the skilled miner, but of all human beings, working or traveling anywhere. This element of mine safety, sometimes called the moral hazard, has been admirably shown by statistics, compiled from the records of the Department of Mines of the Union of South Africa, to be due in about equal measure to the carelessness of the miner and to that of the operator. These statistics show that about one-half the fatalities in mines are due to the so-called hazard of the industry, or what is sometimes called the dangers inherent to work or misadventure. Of 2497 fatalities investigated, including over 200,000 employees, for a period of over 21/2 years, it was found that 17.5 per cent. were due to faulty plant or material, fault of the foreman, or of the management—in short were due to the operator; 17.1 per cent. to disobedience of orders, carelessness or ignorance of injured persons; and 5.9 per cent. through fault of others, including fellow workmen. The fault of the operator is evidenced by failure to give proper warning, failure to inspect, failure to furnish proper equipment, and neglecting to comply with the recommendations of the inspector. That education and training of the mine operator, as well as of the mine worker,

Jan 1, 1918

By V. R. Garfias R. V. Whetsel

Production of crude petroleum in Mexico during 1935 totaled approximately 40,082,000 bbl., an increase of 1,925,000 bbl. over the previous year. Successful development continued in the Poza Rica field during the year, increasing production in that area from 3,708,000 bbl. in 1934 to 9,542,000 in 1935. The output of the South fields (Golden Lane) area decreased by 3,000,000 bbl. during the year, and the heavy-oil district of the Northern fields by 1,500,000 bbl. Production in the Tehuantepec fields showed a slight gain. Production of natural gasoline increased from 430,000 to 600,000 bbl. in 1935. Crude run to stills in local refineries is estimated at 30,000,000 bbl., some 4,000,000 bbl. more than in the previous year. Exports of crude and refined products were approximately 22,000,000 bbl., or 2,000,000 bbl. less than in 1934. Exclusive of ships bunkers, domestic consumption increased about 900,000 bbl. during the year, reaching an estimated total of 14,500,000 barrels. Only 74 wells were completed, as compared to 148 in 1934 and 91 in 1933. In proven areas 58 completions resulted in 33 producers and 25 failures. In northeastern Mexico, near the United States border, six wildcat wells were completed, all of which gave little or no encouraging results, except Rancheria No. 3, near Camargo, which is a fair-sized gas well. Four wildcats were drilled just northeast of the Northern fields (heavy-oil district), all of which were failures. A deep test was completed a short distance southeast of the Golden Lane (South fields) in Palo Blanco, which encountered small production not sufficient to exploit. On the Isthmus of Tehuantepec a wildcat well was completed for an estimated initial production of 2000 bbl. daily, a short distance south of the old Jalapa field, which was perhaps the most important new development of the year. Four other wildcats drilled in the Isthmus district resulted in failures. Fields Northern Fields (Heavy-oil District).—In the Northern fields, 18 producing wells and 20 failures were completed, as compared to 34 producers and 71 failures in 1934. The initial production of the new

Jan 1, 1936

By V. R. Garfias R. V. Whetsel

Production of crude petroleum in Mexico during 1935 totaled approximately 40,082,000 bbl., an increase of 1,925,000 bbl. over the previous year. Successful development continued in the Poza Rica field during the year, increasing production in that area from 3,708,000 bbl. in 1934 to 9,542,000 in 1935. The output of the South fields (Golden Lane) area decreased by 3,000,000 bbl. during the year, and the heavy-oil district of the Northern fields by 1,500,000 bbl. Production in the Tehuantepec fields showed a slight gain. Production of natural gasoline increased from 430,000 to 600,000 bbl. in 1935. Crude run to stills in local refineries is estimated at 30,000,000 bbl., some 4,000,000 bbl. more than in the previous year. Exports of crude and refined products were approximately 22,000,000 bbl., or 2,000,000 bbl. less than in 1934. Exclusive of ships bunkers, domestic consumption increased about 900,000 bbl. during the year, reaching an estimated total of 14,500,000 barrels. Only 74 wells were completed, as compared to 148 in 1934 and 91 in 1933. In proven areas 58 completions resulted in 33 producers and 25 failures. In northeastern Mexico, near the United States border, six wildcat wells were completed, all of which gave little or no encouraging results, except Rancheria No. 3, near Camargo, which is a fair-sized gas well. Four wildcats were drilled just northeast of the Northern fields (heavy-oil district), all of which were failures. A deep test was completed a short distance southeast of the Golden Lane (South fields) in Palo Blanco, which encountered small production not sufficient to exploit. On the Isthmus of Tehuantepec a wildcat well was completed for an estimated initial production of 2000 bbl. daily, a short distance south of the old Jalapa field, which was perhaps the most important new development of the year. Four other wildcats drilled in the Isthmus district resulted in failures. Fields Northern Fields (Heavy-oil District).—In the Northern fields, 18 producing wells and 20 failures were completed, as compared to 34 producers and 71 failures in 1934. The initial production of the new

Jan 1, 1936

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By M. R. Todd, J. Szekely

THE mechanism of carbon oxidation in steelmaking processes has attracted considerable attention in recent years. The generally accepted model postulates that the reaction between carbon and oxygen occurs at the surface of CO bubbles that originate at the suitable nucleation points and subsequently rise through the metal bath.1-4 Although this model describes adequately the behavior of open-hearth type operations, it is not a satisfactory representation of carbon oxidation in oxygen steelmaking processes since it cannot account for either: i) the very high rate of oxidation per unit bath area,or ii) the commonly reported shapes of the curves showing the dependenie of the oxidation rate on the carbon concentration. The very high decarburization rates commonly encountered in oxygen steelmaking processes need no further elaboration; some typical plots of the rate of carbon removal against carbon concentration, taken from a publication by Li, Dukelow, and smith,' are reproduced in Fig. 1. It is seen from the curves that the decarburization tends to decrease from a peak or a plateau once the carbon concentration falls below a certain value; in the experiments reported, this critical value ranged from 1.2 to 0.2 wt pct C. The apparent dependence of the decarburization rate on the carbon concentration indicates that within this region phenomena associated with the transfer of car- bon must play an important if not predominant role. Since the concentration of oxygen in molten iron at steelmaking temperatures (removed from the immediate impact zone) is only about 0.1 wt pct,6 it is clear that simple simultaneous diffusion of carbon and oxygen to the surface of CO bubbles could not account for the rate of carbon transfer being the controlling step at carbon concentrations as high as 1.0 wt pct. The purpose of this communication is to present an alternative model which may explain at least qualitatively the apparent anomalies mentioned and may stimulate further experimental work. The Physical Model. It is suggested that the principal mechanism of decarburization is the reaction between CO bubbles and an emulsion consisting of molten iron and molten iron oxide particles in the vicinity of the "slag-metal interface9'.* This mech-

Jan 1, 1968

By M. E. Straumanis, S. M. Riad

The lattice parameter of 99.999 pct pure Ag rtlas redetevnzined and found to be az5 = 4.08626 5 0.000041 with the vefnzctiotz correction included); the expatzsion coejjicient between 10° and 65°C was 18.73 X10-6°C-1. The lattice paratneter increased upon solution indium in silver in good agrement with other authors. The solid-solubility limit around room temperature was at 20.4 wt pct of in, which suggests that the high-temperature solubility (at about 689°C) determined by other authors is too low. The expansion coejficient of si1ver increases with the itzcrease of indium content between 10° and 65° C from, 18.73 (In = 0) to 20.9 x 10-6°C-1 (In = 20.4 pct), being only very slightly influenced by small amounts of indium. The expansion coefficents of all solid solutions increarsed strongly with temperature, reaching values > 27 x 10- 6 800°C. ACCORDING to the Ag-In diagram,' the solubility of indium in silver (the a phase) extends to about 18 pct by weight at room temperature. However, there has been only one investigation of the solubility limit by X-ray methods—that of Weibke and Eggers.2 Hume-Rothery, Lewin, and Reynolds measured only the lattice parameters of Ag-In solid solutions3 as did Owen and Roberts4 and Adler and Wagner.' The thermal expansivity of four solid solutions was determined by Owen and Roberts4 in a temperature range between 25" and 300°C. In view of the limited amount of work on Ag-In solid solutions, it seemed appropriate to redeter-mine the lattice parameters and the room-temperature solid-solubility limit, to find the exact expansion coefficients of the solid solutions at about room temperature (between 10° and 60°C) and the expansivity up to 800°C, and finally to derive the thermal-expansion coefficients for any alloy within the solid-solubility region. THE ALLOYS AND THE DETERMINATION OF LATTICE CONSTANTS The metals used were 99.9991 pet pure, supplied by the ASARCO company. Both silver and indium were weighed accurately on an analytical balance in

Jan 1, 1965