Search Documents

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

Jan 1, 1949

By L. W. Page

PREVIOUS to the introduction of the motor vehicle the broken stone or macadam road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear. of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appre¬ciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled, as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 2, 1914

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By H. I. Aaronson, C. Wells

THIS is a preliminary report on a detailed metal- lographic investigation of the bainite reaction in a plain carbon hypoeutectoid steel. In view of the current interest in the bainite reaction and of the controversies which still exist about even the basic phenomenology of this mode of transformation, it was considered desirable to present a summary of the more important results obtained to date prior to the completion of this investigation. The steel used contained 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was homogenized for 48 hr at 1250°C. Individual specimens were then austenitized for 30 min at 1300°C and isothermally transformed for various times at temperatures above and within the bainite region, ranging from 775" through 500°C at intervals of 25°C. These specimens were carefully examined on a research metallograph; a few specimens of especial interest were also studied electron microscopically.' Bainite may be defined as the aggregate structure resulting from the precipitation of carbides from supersaturated ferrite which formed by nucleation and diffusion-limited growth. Two groups of experimental observations made during the present study provide support for this mechanism of the bainite reaction: 1—at 625°C, partial conversion of pro-eutectoid ferrite to bainite began after more than 99 pct of the austenite had decomposed and 2—the precipitation of bainitic carbides occurred only within the ferrite phase. The proeutectoid ferrite and the bainite reactions in the steel studied were found to be morphologically continuous. Following the classification scheme of Mehl and Dube,2 three principal morphologies of proeutectoid ferrite were identified in the temperature region (625" to 550°C) in which the two reactions blend—grain boundary allotriomorphs," * Grain boundary allotriomorphs are crystals which nucleate at and grow preferentially along matrix grain boundaries. Widmanstaetten side plates, and intragranular plates. Carbide precipitation converted these morphologies into their bainitic equivalents with increasing isothermal reaction time. Conversion took place more rapidly as the reaction temperature was reduced. The replacement of supersaturated ferrite by bainite, however, did not occur uniformly even within individual austenite grains and was noticeably incomplete at higher transformation temperatures, e.g., 625° to 575°C. The ferritic and bainitic forms of a given morphology thus were frequently found to coexist, often inextricably intermixed, in a given specimen. At 625" and 600°C, the conversion of ferrite to bainite was clearly seen to have occurred entirely by the nucleation of carbides at ferrite/ferrite boundaries, as shown in Fig. 1. The nature of the loci at which carbides formed at lower temperatures was often difficult to ascertain with a light microscope, although the alignment in rows of many of the carbides, illustrated in Fig. 2, suggested that nucleation had again occurred at grain boundaries or subboundaries within the ferrite. Application of the electron microscope confirmed this deduction for bainitic structures formed at these temperatures, as shown in Fig. 3. The dense black appearance of bainite formed at very low reaction temperatures in higher carbon steels3 indicates, however, that isolated lattice defects within ferrite crystals prob-

Jan 1, 1956

By Walter Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. CASE I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected.

Jan 1, 1937

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By F. H. Wilson, E. W. Palmer

G. L. Bailey (British Non-Ferrous Metals Research Association, London, England)—I was glad to see this further work on the structure and properties of the Cu-Ni-Fe alloys of low nickel content in which we have been so interested in the United Kingdom since before the war." The authors' data on the variation in solubility of iron in both 5 and 10 pct Ni alloys with temperature is based on more detailed observations than we have made but is generally in line with our own work. The difficulty in these matters is in the identification of the structures obtained. The precipitation of the second phase which we presume to be the a' solid solution, richer in nickel and iron, from the a solution with which it is in equilibrium occurs in such a fine state of division that its resolution by ordinary micro-graphic methods is impossible in the early stages. We have published some electron micrographs which illustrate the effects observed more clearly but we agree with the authors when they say that dark staining characteristics when the alloys are subjected to sea-water corrosion are more sensitive in detecting the presence of the a' phase than is the microscope. After taking this point into consideration, however, I confess to some difficulty in understanding Fig. 4. I can only assume that the precipitates visible at such a low magnification as 150 diam in these relatively coarse forms are produced from iron-rich areas of the initial solid solution due to inadequate homogenization. If this is so I find it difficult to accept the authors' contention that such local variations in iron concentration as are capable of giving the heavy precipitates shown in Fig. 4 do not in fact materially affect the solvus surfaces of their equilibrium diagrams. I share the authors' enthusiasm about the resistance to corrosion of these alloys by seawater but I am not fully in agreement with them on the vexing question of the best iron content for these alloys. In Fig. 3 of ref. 8, we give many results showing that the resistance of these alloys to impingement attack in the Jet Test increases as the iron content rises to 2 pct. With higher iron contents pitting at shielded areas is likely to occur. Admittedly the addition of 0.75 pct Fe produces a large improvement in corrosion resistance compared with a pure 90/10 Cu-Ni alloy, but the further improvement on raising the iron to 2 pct is substantial. We recommend from 1.5 to 2 pct Fe as the desirable range from the point of view of corrosion resistance. While it is true that British practice generally uses a hard tube, the corrosion resistance of the 10 pct Ni alloys has in our work been little affected by the structural condition. Although the annealed alloys blacken in seawater, this effect seems to be superficial and not to be accompanied by any real decrease in

Jan 1, 1953

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By Clarence P. Linville

(Pittsburg Meeting, March, 1910.) IT is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition ; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which . make the fuel practically uniform ; the Gayley

Mar 1, 1910

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970

By Woolf, W. G.

Filtration of hot (60°C) supersaturated zinc sulphate solution (sp gr 1.540) from slimy leach residues at the electrolytic zinc plant of Sullivan Mining Co., Kellogg, Idaho, is de- scribed. Separation of liquids and solids in the finished leach is by Burt filters modified to meet conditions of high-acid, high-density process for electrolytic zinc. Operating characteristics of the Burt filter on this pulp are presented.

Jan 1, 1950

By Scott Turner

AS IN OTHER lines of engineering, progress in mining was influenced during 1931 by the world-wide economic depression. Low-metal prices ? resulted in active efforts to reduce production costs of base-metal mines. Probably the chief factors in reducing costs were the greater efficiency of labor, due to better relations between management and workmen, to the scarcity of jobs, reduced wages in most base-metal mines, and to lower overhead expenses secured by drastic economies. The use of mechanical equipment continued to increase, due to more efficient designs and a better practical understanding of the applicability of such equipment to requirements. With one exception, there were no startling innovations in stoping methods, but there was notable progress in the better adaptation of mining methods. In the United States, no large new base-metal or silver mines came into production during the year. At a number of mines, output was curtailed, and operations were discontinued at several important producers. On the other hand world-wide interest in gold was stimulated, as evidenced by increased output from producing mines, the reopening of some old properties, and intensive prospecting for new deposits. Mining methods at several gold mines in the United States and Canada were modified or changed to obtain a higher extraction of ore or to meet the need for additional support of the mine workings at depth. Permanent record of improvements in mining practices has been made during the year by the Federal Government; the industry thus has available for its use more detailed information than ever before. This work was done through cooperation of the mining companies and their representatives with the United States Bureau of Mines, whereby many papers descriptive of practices and costs at individual mines have been published. The Bureau's program of describing methods and costs at the more important mines (those producing in excess of $100,000 annually) is nearly completed, but papers will be issued concerning such additional mines as may possess particular interest because of novel methods, exceptional conditions or operating results, and others to supplement reports already issued. In this way, an interesting record of the results of changing conditions, or innovations in methods, will be made available.

Jan 1, 1932

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS CHESTER A. FULTON, Chairman CARROLL A. GARNER H. Y. WALKER WALLACE E. PRATT FELIX E: WORMSER PAUL D. MERICA, Consultant FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERIE V. DAVELER, Chairman WILBER JUDSON RUSSELL B. PAUL HENRY KRUMB, Consultant

Jan 1, 1944

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By C. S. Simons

Manufacturers of filtering, thickening or clarifying equipment, have been active in developing machines to meet increasingly rigid operator requirements, and the innovations resulting from this effort are moving into commercial applications. In general, the results of these applications are reported to be good. Little has been reported on progress in theory. The growing insistence on the part of pollution control agencies that waste water discharged into streams contain less and less suspended solids is being felt by a broad cross section of industry. A new clarifier, based on the often rediscovered fact that suspended solids settle more rapidly in inclined channels, is being marketed by Neptune MicroFLOC of Corvallis, Ore. This unit employs modules of inclined tubes, mounted in the upper zone of the clarifier, which carry the water flow. These were developed for light solids, such as those encountered in domestic water treatment and in paper mill waste water. In these applications, flow rates up to about three times those permissible in conventional clarifiers are reported to give comparable overflow turbidity. By combining these units with mixed media filters, high clarity may be obtained with minimum capital. Use of such units in the metallurgical industry, particularly where water reuse or effluent quality is important, should grow.

Jan 1, 1970

THE hall of the Western Iron and Nail Associations having kindly been placed at the service of the Institute, the opening session was held at 3 o'clock, Tuesday afternoon, May 13th, with an attendance of about one hundred and twenty-five members. Mr. William Metcalf, of Pittsburgh, read an address of welcome on behalf of the Local Committee of Arrangements, to which President E. B. Coxe responded. The following papers were then read and discussed : Regenerative Stoves; a Sketch of their History and Notes on their Use, by John M. Hartman, of Philadelphia. Some Curious Phenomena Observed on Making a Test of a Piece of Bessemer Steel, by William Kent, of Pittsburgh. On the Use of Determining Slag Densities in Smelting, by Thomas Macfarlane, of Wyandotte, Michigan. After the reading of these papers each member was presented by the Local Committee with a schedule of excursions, a specially prepared map of Pittsburgh and surroundings, and a directory of industrial works, all tastefully bound, and also with a metal badge bearing the seal of the Institute, to be worn on the excursions. The second session was held on Tuesday evening. The following persons, duly proposed for members and associates of the Institute, were, on the recommendation of the Council, unan¬imously elected. (In this list are included those elected at the final session on Friday morning.) George Bartol, - Cleveland, Ohio. Luther S. Bent, - Steelton, Dauphin Co., Pa. Octave Chanute, - New York City. Albert H. Childs, - Allegheny, Pa. Theodore Cooper, - New York City. Andrew Cosgriff, - Brewster, Putnam Co., N. Y. William B. Crocker, - New York City. Henry M. Curry, - Pittsburgh, Pa. Charles Davis, - Allegheny, Pa. Henry F. De Bardeleben, - Birmingham, Ala. Herbert Du Puy, - Pittsburgh, Pa. Charles L. Fitzhugh, - Pittsburgh, Pa. W. S. Franklin, - Ashland, Md. F. G. Fricke, - Pittsburgh, Pa. Paul A. Fusz, - St. Louis, Mo. Ignatius Hahn, . Pittsburgh, Pa. Henry Hargreaves, - South Pittsburgh, Tenn.

Jan 1, 1880

By Horace L. Wells

The gravimetric determination of titanium in irons and steels is extremely difficult. It may be well, therefore, to call the attention of those members of the Institute who are interested in the chemistry of iron to a colorimetric! method, which I have slightly elaborated to adapt it to the case under consideration. Schön * discovered that hydrogen peroxide produces, in certain solutions of titanic acid, a very intense color similar to that of ferric

Jan 1, 1886