Search Documents

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir's previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l'unctions, can be used to calculate future behavior for any production schedule.

By R. A. Swalin, A. H. Geisler

THIS study represents an investigation of the effect of annealing temperature on the texture of drawn molybdenum, iron, and an iron alloy containing 14 pct Al. The effect of temperature on annealing textures has not been widely investigated in the past. One of the obstacles in making such a study using usual X-ray diffraction techniques results from the

Jan 1, 1957

ROBERT H. LEACH, Chairman ROBERT F. MEHL, Past-Chairman D. K. CRAMPTON, Vice-Chairman E. M. WISE. Vice-Chairman W. M. CORSE, Treasurer LOUIS JORDAN, Secretary 29 West' 39th St., New York, N. Y. Executive Committee 1940 1941 ARTHUR PHILLIPS W. P. SYKES L. E. SCHUMACHER E. A. ANDERSON CARL E. SWARTZ D. L. COLWELL 1942

Jan 1, 1939

"Acta Metallurgica" Dennis Carney, '59 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science F T Agthe, Dec '59, William L Fink, Dec '60 American Geological Institute Arthur Montgomery, Oct , '59, F C Kruger, Oct '60 American Power Conference J P Weir, T D Hess American Society for Testing Materials

Jan 1, 1959

By AIME AIME

MICA is perhaps our No. 1. strategic mineral problem because of its large requirements in a variety of equipment for use in the military services, and because the principal source of this material has heretofore been British India, a source now threatened partly because of distance and lack of ships. [Block mica and bauxite were added to the "most critical" list published by the W.P.B. on Nov. 6.] No satisfactory substitute has yet been found for most of the uses of mica, which largely involve electrical insulation. Brazil is now our nearest and best major source of this material. No splitting plants have yet been established there but in 1941 we imported about a million pounds of block mica from that country and in 1942 that quantity will be considerably exceeded. In Brazil, mica is found almost exclusively in the pegmatite dikes along the mountain range bordering the eastern part of Minas Gerais. A belt, roughly 180 miles long by 100 miles wide, extends from Theophilo Ottoni to Carangolo. The principal mica-mining districts in this belt are the Governador Valladares area to the north and the Espera Feliz district to the south. The dikes are usually 10 to 50 meters wide and a mile or two long and intrude the old metamorphic schist formation. They are weathered and easily mined.

Jan 1, 1942

By AIME AIME

BY the end of 1943, the United States will be able to produce aluminum at a rate of 1,150,000 tons a year. How much aluminum is 1,150,000 tons? It is sufficient to replace every railroad passenger car in this country three times a year. Or, it would put a thirty-piece aluminum cooking utensil set in every one of America's 34,000,000 homes with enough metal left over to make 5,000,000 miles of aluminum transmission cable, such as was used in the electrification of much of rural America. Expansion of aluminum production capacity for the war program has occurred in three steps: (1) expansion by private industry; (2) the letting of contracts by the Defense Plant Corp. for the construction of additional aluminum plants which may remain after the war to compete with existing facilities; and (3) the more recently announced D.P.C. program for the building of emergency plants to make aluminum, using stand-by power available in large metropolitan centers power of relatively higher cost, making it questionable whether such plants, now gravely needed, will be able to compete in a peacetime economy.

Jan 1, 1943

By R. V. Norris

In a former paper on this subject,' I summarized Murgue's theory and experiments, and presented a large number of tests of mine-fans, stating some conclusions, " more or less warranted by the evidence," as to design, capacity and efficiency. Since that time the very valuable report of Mr. M. Walton Brown: Committee on Mechanical Ventikators, Institution of Mining Engineers, has appeared, and I have made additional experiments which tend to clear up some points in connection with this subject. Design and Tests of the Luke-Fidlbr Colliery Fan. The Luke-Fidler fan (see Figs. 1, 2 and 3), built to replace an old wooden fan at a very fiery colliery, presents some pecu-

Jan 1, 1905

By C. S. Matthews, P. Hazebroek, F. Brons

A method has been developed for calculating the average pressure in a bounded reservoir. The reservoir is first divided into the individual drainage volumes of each well, by using the criterion that at steady state each individual drainage volume is proportional to a well's production rate. The average pressure in each drainage volume is then calculated by a method developed in the report. By volumetrically averaging these individual drainage volume pressures, the average pressure in the entire reservoir is obtained. To calculate the average pressure in each drainage volume, a correction is applied to the ordinary extrapolated pressure, i.e., the pressure obtained by extrapolating to infinite time the linear portion of the graph of closed-in pressure versus log[?t/(t + ?t)], where At is the closed-in time and t the production time. The correction, which is a function of the production time, is presented in graphical form for different shapes of the drainage area (horizontal cross section of the drainage volume). INTRODUCTION It is important to be able to find the volumetric average pressure in a reservoir so that the size of the reservoir may be determined from material balance calculations. It is also desirable to be able to find the approximate distribution of pressure within a reservoir for detection of fluid movement. 'The purpose of this paper is to present a method for calculating both the average reservoir pressure and the approximate distribution of pressure within a bounded reservoir — that is, a reservoir with no water drive. In reservoirs where the pressure builds up rapidly after wells are shut in, the determination of average pressure generally poses little problem, for one often need only average the final buildup pressures. It is when pressure buildup is slow that difficulties arise. For practical and economical reasons, the time allowable for closing in wells is limited. If at the maximum allowable closed-in time the pressure has not reached a con- stant value (and this is more often the case than is generally realized), calculation of average pressure presents difficulties. One method which has been used in the past for obtaining an "average" pressure involves the extrapolation to infinite closed-in time of curves of pressure as a function of closed-in time. Contour maps of these extrapolated pressures are used in arriving at an average pressure. In some cases wells are shut in for arbitrary Lengths of time, and contours of these arbitrary shut-in pressures are used for calculation. All these methods are somewhat arbitrary and suffer from lack of fundamental theoretical basis. For example, no precise meaning can be given either to the extrapolated or to the arbitrary shut-in pressure. Furthermore, there seems to be no reason why either set of pressures should be contourable. It was because of the vagueness of these old methods and their lack of a sound theoretical basis that, the present method for determining average reservoir pressure was developed. SYMBOLS A = drainage area of a well, cm' A, = drainage area of well j, cm2 A , = total drainage area of all wells in a reservoir, cm2 c = coefficient of compressibility of fluid at reservoir temperature, atm-1 f = hydrocarbin-filled porosity, fraction h = net thickness of formation, cm k = permeability of formation, darcy p = pressure at a well, atm p0 = initial reservoir pressure, atm p* = pressure obtained by straight-line extrapolation of linear portion of plot of p versus log [At/(t+ At)] p = volumetric average pressure inside drainage volume of a well q = volume flow rate at a well, cc/sec a: prevailing reservoir conditions q, = total volumetric flow rate from a reservoir, cc/sec at prevailing reservoir conditions rw = radius of well bore, cm T = kt/fµcA t = corrected time of production of a well, seconds, defined by

Jan 1, 1955

By Warren Smith

IT has been 5 years since the writer left the Philippine Islands and while in that country his chief work did not lie in this field, though he has visited all but one of the localities mentioned in this article. The principal field studies relating to oil were made by his colleague, Mr. Wallace E. Pratt. The writer's investigations dealt with the general stratigraphy and paleontology of the Philippines. With the exception of the investigations made by Mr. Pratt and the writer very little information on this subject is available. A number of geologists in the employ of large oil companies have visited the Islands from time to time but, following the general rule, the public has scarcely ever been permitted to learn anything of the results. The writer is indebted to the Bureau of Insular Affairs, Washington, for late information regarding recent legislation in the Islands relating to petroleum. All the known oil seeps, petroleum residues, such as ozocerite, and natural-gas emanations are associated with Tertiary sediments. The chief seeps and most promising prospects are located as follows: 1. Bondoc Peninsula (lower end), Tayabas Province, Southeast Luzon. 2. The west coast of the island of Cebú from Alegria north to, and perhaps beyond, Toledo. 3. Central Mindanao not far from Lake Lanao. 4. The ozocerite veins on the Island of Leyte in the northwestern part in the vicinity of the town of Villaba. 5. Natural gas from some deep wells in Tertiary shale formations on the eastern flank of the Cordillera and extending out under the plain on the island of Panay.

Jan 2, 1920

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By Lyon F. Terry

IN contemplating the prospects of natural gas being transported from the fields where it is produced to such distant points as Philadelphia, New Jersey, New York City, and New England, let us review the advance that natural gas has made and the projects currently scheduled for construction. This may give us a perspective of the point in the long-range development of the natural gas business in which we now find ourselves, and some basis for judging the further expansion of the industry. Authentic statistics of the total marketed production of natural gas in the United States have been compiled by the Bureau of Mines since the year 1906. The growth of the business is indicated by the following data on marketed production for each ten-year interval since 1906:

Jan 1, 1947

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

By Charles Will Wright

ITALY is by- far the poorest in mineral resources of the so-called great pou7ers of Europe. Before the World War this shortage was not so serious as the essential minerals that could not be mined domestically at a profit were bought in the world markets. In those days tourist trade and remittances from Italians abroad helped to provide Italy with foreign exchange. During the World War, when certain mineral products were scarce and when prices rose in some instances to several times normal, the Italian Government began to regulate consumption and imports. It was not until later, when the Fascist regime established the corporate state, that Italy seriously considered adopting a of self-sufficiency. Private industry was grouped under separate corporations, for the principal industries; including mining and metallurgy and the heads of the large producing companies, became members of these corporations. Industrialists were thus able to regulate their own affairs and to advise the Government as to the measures necessary to meet domestic or foreign trade demands upon their industry. Labor was or-

Jan 1, 1939

By G. P. Tiwari

Recrystallization and grain growth in thoria dispersed nickel and nichrome were recently studied by Webster as a function of temperature and deformation. The unexpected part of these results was that specimens which had received heavier deformation developed greater resistance to recrystallization. Retardation of recrystallization was accompanied by the formation of voids around thoria dispersion. To explain these results, Webster suggested that the formation of void around the particles increased the effective size of thoria particles. This resulted in greater impediment to the grain-boundary migration and as a consequence the recrystallization of the matrix is retarded. In the present note an alternative and more probable explanation for the effect of voids on recrystallization is presented. The exact mechanism of void formation in thoria dispersed nickel or nichrome is not known. However, it is reasonably certain that it must be preceded by the stress concentration in the matrix around thoria dispersion during the deformation.'' The resulting stress concentration must be sufficient enough to supply the surface energy for the new surfaces created. Further, the decrease in the strain energy of the matrix surrounding the potential void nucleus must be larger than the surface energy of the newly created surface. The release of strain energy due to formation of crack results in a strain free cylinder of the material around the voids.13 If the void formation is not localized, at few points only (as is the case here), this process may lead to considerable amount of release of strain energy of the matrix. The pattern of recrystallization behavior of single phase homogeneous matrix as well as the matrix having a second phase dispersion is same except for the fact recovery and recrystallization are more clearly delineated.14 In general, the recrystallization temperature is lowered (i.e., recrystallization is easier) with increase in the amount of cold work. This is due to the increase in stored energy in the matrix with increasing amount of deformation. If somehow there is a relaxation of strain energy in the matrix, the recrystallization should become difficult because of the decrease in the amount of stored energy available for recrystallization. Since the formation of voids leads to a decrease in the strain energy of matrix, the recrystallization of the matrix would be inhibited due to the formation of voids during deformation prior to recrystallization. It has been observed by earlier workers15'16 that the presence of preexisting voids in a matrix retards the recrystallization. The essential issue here is how do the voids act to produce this effect. If the voids influence recrystallization only by blocking the grain boundary migration, then the effect should be maximum when they are present almost exclusively along grain boundary. These conditions are obtained during high temperature deformation. However, the voids produced due to creep along grain boundary are not able to prevent recrystallization17 suggesting that they are not effective in blocking grain boundary movement. Recently it was shown by Davies and Williams that the voids can act as sinks for vacancies." As a result the processes dependent on vacancy diffusion like recovery, recrystallization, dislocation climb, and so forth, will be hindered. This fact may be responsible for inhibition of recrystallization during subsequent deformation and annealing cycles. It is to be noted here that there is a large difference between the density of voids in creep experiments and the other experiments where retarding effect of voids on recrystallization is seen. The voids in former may number up to l04 to l05 per sq cm whereas in latter cases the voids density is typically around 1010 to 1013 per sq cm. It appears that the decrease in supply of vacancies in creep is insufficient to adversely affect the recrystallization due to low void population. The author is grateful to P. Das Gupta and S. P. Ray for helpful discussions. Author's Reply D. Webster Tiwari appears to have misunderstood the nature of grain boundary-particle interactions. Tiwari (quoting Cahn) states that second phase particles become more effective as they become smaller, therefore as the voids in TDNiC make the thoria particles effectively bigger their ability to resist grain boundary movement is impaired. This particle size argument was originally proposed in the form of an equation by Zener 20 years agol9 and is not necessarily valid as is discussed below. However, assuming it is valid, it predicts a greater boundary restraining effect by smaller particles simply because their combined cross sectional area is greater at a constant volume. If the number of particles remains the same and their effective size increases, as in the present case, Zener's equation predicts a greatly reduced grain size. This is because the effect

Jan 1, 1970

Jan 1, 1888

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

Organization Place Date 1918 American Institute of Architects Washington, D. C. April American Iron and Steel Institute New York, N. Y. May American Institute of Chemical Engineers : Berlin, N. H. June 19-22 American Society for Testing Materials Atlantic City, N. J. June 25-28 New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. 9-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N.. J. Sept.

Jan 4, 1918

By R. R. Seeber

(Pittsburg Meeting, March, 1910.) IN the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large-from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.1 The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. , The hoist for No. 4 shaft, is about 1,700 ft. from the power-plant, and in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-generator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-kw, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910. Engineering and Mining Journal, vol. lxxxviii., No. 3, p. 110 (July 17, 1909).

Sep 1, 1910